Re: LSI Logic fibre channel adapter in FreeBSD 6.0-BETA3

From: Mischa Peters <mischa.peters_at_gmail.com>
Date: Sat, 10 Sep 2005 22:28:53 +0200
On 8/30/05, Mischa Peters <mischa.peters_at_gmail.com> wrote:
> On 8/29/05, Krzysztof Ciepłucha <kris_at_home.pl> wrote:
> > Mischa Peters wrote:
> > > Hi All,
> > >
> > > I am not sure if this is the correct list. But I have the following issue.
> > >
> > > I have a Fibre Channel card in my server, LSI Logic FC909A which was
> > > working fine under FreeBSD 4.11 but is no longer working with
> > > 6.0-BETA3. I have also tried it with BETA1 which also didn't work.
> > >
> > > The thing that I see in messages is:
> > >
> > > pci0: <serial bus, Fibre Channel> at device 11.0 (no driver attached)
> > > pci0: <serial bus, Fibre Channel> at device 11.1 (no driver attached)
> > >
> > > I have seen that in GENERIC the old ncr drivers are disabled and are
> > > replaced with sym.
> > > Does this matter at all, or is this b0rken and does it needs fixing?
> >
> > man mpt
> >
> > HARDWARE
> >       The following controllers are supported by the mpt driver:
> >
> >       o   LSI Logic 53c1030 (Dual Ultra320 SCSI)
> >       o   LSI Logic FC909 (1Gb/s Fibre Channel)
> >       o   LSI Logic FC909A (Dual 1Gb/s Fibre Channel)
> >       o   LSI Logic FC919 (2Gb/s Fibre Channel)
> >       o   LSI Logic FC929, LSI Logic FC929X (Dual 2Gb/s Fibre Channel)
> >
> >
> 
> I have verified that this is indeed enabled in the kernel conf file.
> 
> device          mpt             # LSI-Logic MPT-Fusion
> 
> Anything else that I need to check?

Just installed BETA4 and I am still not able to get the card working.

root:~ # pciconf -vl
none0_at_pci0:11:0:        class=0x0c0400 card=0x10101000 chip=0x06261000 rev=0x00 
hdr=0x00
    vendor   = 'LSI Logic (Was: Symbios Logic, NCR)'
    device   = 'LSIFC929X Dual Channel Fibre Channel I/O Processor'
    class    = serial bus
    subclass = Fibre Channel
none1_at_pci0:11:1:        class=0x0c0400 card=0x10101000 chip=0x06261000 rev=0x00 
hdr=0x00
    vendor   = 'LSI Logic (Was: Symbios Logic, NCR)'
    device   = 'LSIFC929X Dual Channel Fibre Channel I/O Processor'
    class    = serial bus
    subclass = Fibre Channel

root:~ # kldstat 
Id Refs Address    Size     Name
 1    4 0xc0400000 664d84   kernel
 2   16 0xc0a65000 573c4    acpi.ko
 3    1 0xc283f000 4000     nullfs.ko
root:~ # kldload mpt
kldload: can't load mpt: File exists
root:~ # kldunload mpt
kldunload: can't find file mpt: No such file or directory

Anyone?

Mischa
Received on Sat Sep 10 2005 - 18:35:11 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:43 UTC