Re: ath0 driver

Hi, 
> > >The version should be 0.9.5.3 or better (can't remember if I committed .4
> > >or .3).
> >Shouldn't that be 0.9.5.2?  I run the latest current, and
> >hw.ath.hal.version is 0.9.5.2.
>

>You're right; I committed a slightly older version to FreeBSD than to Linux.
>The version

The version I have is 0.9.5.2. As to the tcpdump, I get 

er# tcpdump -i ath0 -y IEEE802_11
tcpdump: data link type DLT_IEEE802_11
tcpdump: listening on ath0
00:18:02.152294 10.0.0.1.netbios-dgm > 10.0.0.255.netbios-dgm: NBT UDP 
PACKET(138)
00:18:02.152502 10.0.0.1.netbios-dgm > 10.0.0.255.netbios-dgm: NBT UDP 
PACKET(138)

and thats all that comes up.

Does this driver support being set up as an access point yet?
I figured it did because ifconfig ath0 mediaopt hostap   didnt return any 
errors. 

Please let me know if Im doing something wrong. Im sure ive got my *.conf 
files set up right as I have used them before, however I could be wrong.

Thanks for the help

David
> > Ive got a Dlink DWL-G520 that Ive installed into a Freebsd system. Ive
> > set up  the card with the following00:18:02.152294 10.0.0.1.netbios-dgm > 
10.0.0.255.netbios-dgm: NBT UDP PACKET(138)
00:18:02.152502 10.0.0.1.netbios-dgm > 10.0.0.255.netbios-dgm: NBT UDP 
PACKET(138)

> > ifconfig_ath0="inet 10.0.0.1 netmask 255.255.255.0 ssid daves channel 10
> > media  DS11 mediaopt hostap"
> >
> > This system was cvsuped and buildworld about 3 days ago. The card appears
> > to  be working because when I try to connect with my PDA it shows full
> > Link and  quality, and when I ifconfig ath0 down , the link and quality
> > go down to  nothing.
> >
> > However it doesn't give out dhcp addresses over this interface. Im sure
>
> my
>
> > dhcpd.conf is fine because I've used a similar one on a laptop => aka
> > wireless access point that worked very well. So I tried to use dstumbler
> > to  see if it could detect the PDA, however it gives me the following
> > error
> >
> >  error: unable to ioctl device socket: Operation now in progress
> >
> > and it stays that way.
> >
> > Has anyone had this issue as well or now what it means?
>
> Verify you have the latest HAL using
>
> sysctl hw.ath
>
> The version should be 0.9.5.3 or better (can't remember if I committed .4
> or .3).  If you have an old version update.  Otherwise you might try
> tapping 802.11 frames with tcpdump on the AP to see what's going on:
>
> tcpdump -i ath0 -y IEEE802_11
>
> As to dstumbler, it is intimately tied to the wi driver at the moment.  I
> have a version that works w/ wi and ath drivers but it's a major rewrite
> and incomplete.  If someone wants to pick it up I'd be happy to pass the
> (incomplete) work on...
>
> 	Sam