From: "Nate Lawson" <nate_at_root.org> To: "Igor B. Bykhalo" <goshik_at_binep.ac.ru> Cc: <current_at_freebsd.org> Sent: Wednesday, August 13, 2003 2:56 AM Subject: Re: A-DATA flash drive: some oddities and how to add USB quirks > Looking at your dmesg output, I see that your drive is reporting that it's > "not ready". However, your dmesg doesn't show any actual failure. > Instead it looks like CAM retries and then succeeds in probing the device. > > Please report the exact failure behavior and the dmesg of any errors. > > -Nate Failures: In attemp to mount: > Script started on Wed Aug 13 15:48:11 2003 > goshik# mount -v -t msdos /dev/da0s1 /mnt > msdos: /dev/da0s1: Device not configured > goshik# exit > exit > > Script done on Wed Aug 13 15:48:26 2003 Accompanied by console messages: > Aug 13 15:48:23 goshik /kernel: (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 > Aug 13 15:48:23 goshik /kernel: (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 > Aug 13 15:48:23 goshik /kernel: (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 > Aug 13 15:48:23 goshik /kernel: (da0:umass-sim0:0:0:0): NOT READY asc:3a,0 > Aug 13 15:48:23 goshik /kernel: (da0:umass-sim0:0:0:0): Medium not present Some usb and camcontrol output: > Script started on Wed Aug 13 15:39:37 2003 > goshik# usbdevs -v > Controller /dev/usb0: > addr 1: self powered, config 1, UHCI root hub(0x0000), VIA(0x0000), rev 1.00 > port 1 addr 2: self powered, config 1, USB Embedded Hub(0x2515), A-DATA Technology Inc.(0x067b), rev 0.01 > port 1 addr 3: self powered, config 1, USB Mass Storage Device(0x2517), A-DATA Technology Inc.(0x067b), rev 0.01 > port 2 powered > goshik# camcontrol rescan all > Re-scan of bus 0 was successful > goshik# camcontrol devlist -v > scbus0 on umass-sim0 bus 0: > <A-DATA Flash 2.0 P1.0> at scbus0 target 0 lun 0 (pass0,da0) > scbus-1 on xpt0 bus 0: > < > at scbus-1 target -1 lun -1 (xpt0) > goshik# camcontrol inquiry da0 > pass0: <A-DATA Flash 2.0 P1.0> Removable Direct Access SCSI-0 device > pass0: Serial Number > pass0: 650KB/s transfers > goshik# exit > exit > > Script done on Wed Aug 13 15:40:25 2003 Camcontrol commands are accompanied by console messages: > Aug 13 15:40:03 goshik /kernel: (probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 > Aug 13 15:40:03 goshik /kernel: (probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0 > Aug 13 15:40:03 goshik /kernel: (probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 1 80 0 ff 0 > Aug 13 15:40:18 goshik /kernel: (pass0:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0 > Aug 13 15:40:18 goshik /kernel: (pass0:umass-sim0:0:0:0): INQUIRY. CDB: 12 1 80 0 ff 0 >From dmesg (boot -v before above commands): > Copyright (c) 1992-2003 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 4.8-STABLE #31: Wed Aug 13 14:43:41 MSD 2003 > goshik_at_goshik.binep.ac.ru:/usr/obj/usr/src/sys/GO > Calibrating clock(s) ... TSC clock: 1334887190 Hz, i8254 clock: 1193117 Hz > Timecounter "i8254" frequency 1193117 Hz > CPU: AMD Athlon(tm) XP 1500+ (1334.89-MHz 686-class CPU) > Origin = "AuthenticAMD" Id = 0x662 Stepping = 2 > Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> > AMD Features=0xc0480000<MP,AMIE,DSP,3DNow!> > Data TLB: 32 entries, fully associative > Instruction TLB: 16 entries, fully associative > L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative > L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative > L2 internal cache: 256 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative > real memory = 268369920 (262080K bytes) > Physical memory chunk(s): > 0x000001000 - 0x00009ffff, 651264 bytes (159 pages) > 0x000369000 - 0x00ffe7fff, 264761344 bytes (64639 pages) > config> en apm0 > config> di psm0 > config> di ppc0 > config> q > avail memory = 257847296 (251804K bytes) > bios32: Found BIOS32 Service Directory header at 0xc00faf90 > bios32: Entry = 0xfb400 (c00fb400) Rev = 0 Len = 1 > pcibios: PCI BIOS entry at 0xb430 > pnpbios: Found PnP BIOS data at 0xc00fbef0 > pnpbios: Entry = f0000:bf20 Rev = 1.0 > Other BIOS signatures found: > ACPI: 000f66f0 > Preloaded elf kernel "kernel" at 0xc0342000. > Preloaded userconfig_script "/boot/kernel.conf" at 0xc03420a8. > Preloaded elf module "vesa.ko" at 0xc03420f8. > Preloaded elf module "vn.ko" at 0xc0342194. > Preloaded elf module "if_ef.ko" at 0xc0342230. > Preloaded elf module "if_sis.ko" at 0xc03422d0. > Preloaded elf module "miibus.ko" at 0xc0342370. > Preloaded elf module "snd_via8233.ko" at 0xc0342410. > Preloaded elf module "snd_pcm.ko" at 0xc03424b4. > Preloaded elf module "usb.ko" at 0xc0342554. > Preloaded elf module "ugen.ko" at 0xc03425f0. > Preloaded elf module "umass.ko" at 0xc034268c. > Preloaded elf module "snp.ko" at 0xc034272c. [...] > uhci0: <VIA 83C572 USB controller> port 0xd800-0xd81f irq 12 at device 17.2 on pci0 > usb0: <VIA 83C572 USB controller> on uhci0 > usb0: USB revision 1.0 > uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 2 ports with 2 removable, self powered > uhub1: A-DATA Technology Inc. USB Embedded Hub, class 9/0, rev 2.00/0.01, addr 2 > uhub1: 1 port with 0 removable, self powered > umass0: A-DATA Technology Inc. USB Mass Storage Device, rev 2.00/0.01, addr 3 > umass0:0:0:-1: Attached to scbus0 as device 0 > uhci1: <VIA 83C572 USB controller> port 0xdc00-0xdc1f irq 12 at device 17.3 on pci0 > using shared irq12. > usb1: <VIA 83C572 USB controller> on uhci1 > usb1: USB revision 1.0 > uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub2: 2 ports with 2 removable, self powered [...] > ad0: success setting UDMA5 on VIA chip > Creating DISK ad0 > ar: FreeBSD check1 failed > ad0: <WDC WD400EB-00CPF0/06.04G06> ATA-5 disk at ata0-master > ad0: 38166MB (78165360 sectors), 77545 C, 16 H, 63 S, 512 B > ad0: 16 secs/int, 1 depth queue, UDMA100 > ad0: piomode=4 dmamode=2 udmamode=5 cblid=1 > (probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 0 0 0 24 0 > (probe0:umass-sim0:0:0:0): INQUIRY. CDB: 12 1 80 0 ff 0 > (probe0:umass-sim0:0:0:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 > Creating DISK da0 > (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 > pass0 at umass-sim0 bus 0 target 0 lun 0 > pass0: <A-DATA Flash 2.0 P1.0> Removable Direct Access SCSI-0 device > pass0: Serial Number \^_ > pass0: 650KB/s transfers > (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 > ad0s1: type 0xa5, start 63, end = 78156224, size 78156162 : OK > Mounting root from ufs:/dev/ad0s1a > ad0s1: type 0xa5, start 63, end = 78156224, size 78156162 : OK > start_init: trying /sbin/init > (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 > (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 > (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 > (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 > (da0:umass-sim0:0:0:0): NOT READY asc:3a,0 > (da0:umass-sim0:0:0:0): Medium not present > da0 at umass-sim0 bus 0 target 0 lun 0 > da0: <A-DATA Flash 2.0 P1.0> Removable Direct Access SCSI-0 device > da0: Serial Number \^_ > da0: 650KB/s transfers > da0: Attempt to query device size failed: NOT READY, Medium not present > Linux ELF exec handler installed Part of kernel config: >>>> Kernel config: [...] > options SCSI_DELAY=15000 #Delay (in ms) before probing SCSI > options USB_DEBUG > [...] > # SCSI peripherals > device scbus # SCSI bus (required) > device da # Direct Access (disks) > device pass # CAM passthrough driver > > options CAMDEBUG > options CAM_DEBUG_BUS=0 > options CAM_DEBUG_TARGET=0 > options CAM_DEBUG_LUN=0 > options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_CDB" > #options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB" > [...] I can send full dmesg and kernel config if needed. usb, umass and ugen were loaded as modules via loader.conf TIA, IgorReceived on Wed Aug 13 2003 - 03:02:50 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:18 UTC