On 5.2-RC FreeBSD 5.2-RC #2: Thu Dec 11 19:52:34 GMT 2003 (cvsupped a few hours before) I seem to get interrupt routing problem where interrupts that belong to the gigabit ethernet interfaces get also delivered to uhci1; There is nothing connected to the USB connectors. Advice how to debug further appreciated. As a workaround I´m just dropping usb support from the kernel. 0 32 0 18 -64 0 0 12 - RL ?? 4:25.53 (irq19: uhci1) 0 41 0 0 -68 0 0 12 - WL ?? 0:02.27 (irq28: em0) 0 42 0 129 -68 0 0 12 - RL ?? 20:29.17 (irq29: em1) 0 85 0 126 -68 0 0 12 - RL ?? 20:50.71 (irq72: em2) em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.19> port 0x3000-0x303f mem 0xfc200000-0x fc21ffff irq 28 at device 2.0 on pci3 em0: Speed:N/A Duplex:N/A em1: <Intel(R) PRO/1000 Network Connection, Version - 1.7.19> port 0x3040-0x307f mem 0xfc220000-0x fc23ffff irq 29 at device 2.1 on pci3 em1: Speed:N/A Duplex:N/A pcib4: <ACPI PCI-PCI bridge> at device 4.0 on pci0 pcib4: could not get PCI interrupt routing table for \\_SB_.PCI0.HLD_ - AE_NOT_FOUND pci4: <ACPI PCI bus> on pcib4 pci4: <base peripheral, interrupt controller> at device 28.0 (no driver attached) pcib5: <ACPI PCI-PCI bridge> at device 29.0 on pci4 pci5: <ACPI PCI bus> on pcib5 pci4: <base peripheral, interrupt controller> at device 30.0 (no driver attached) pcib6: <ACPI PCI-PCI bridge> at device 31.0 on pci4 pci6: <ACPI PCI bus> on pcib6 em2: <Intel(R) PRO/1000 Network Connection, Version - 1.7.19> port 0x4000-0x403f mem 0xfc400000-0x fc41ffff irq 72 at device 1.0 on pci6 em2: Speed:N/A Duplex:N/A em3: <Intel(R) PRO/1000 Network Connection, Version - 1.7.19> port 0x4040-0x407f mem 0xfc420000-0x fc43ffff irq 73 at device 1.1 on pci6 em3: Speed:N/A Duplex:N/A uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x2000-0x201f irq 16 at device 29.0 on pci0 usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> port 0x2020-0x203f irq 19 at device 29.1 on pci0 usb1: <Intel 82801CA/CAM (ICH3) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered PeteReceived on Thu Dec 11 2003 - 12:31:25 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:33 UTC