Doug White schrieb: > On Wed, 10 Dec 2003, Kay Lehmann wrote: > > >>Hello everybody, >> >>I just did an update of my 5.1-machine. Everything seems to work >>properly, except my network-devices. They are recognized correctly and >>ifconfig says, that they are active but network isn't reachable and I >>get the error message: >> >>watchdog timeout > > > It appears that interrupts aren't getting routed correctly on your system. > Can you describe it? Also, get boot -v output. > Hmm, sorry I don't know how to describe it in detail, boot -v is attached. All I can say is that it does not work with 5.2RC, but works with every previous release. Maybe you could give me some advice on how to descibe it? In detail what I did: cvsup to RELENG_5_2 rebuild everything in the mentioned order, mergemaster etc. tried GENERIC and custom kernel switched slots (3,4,5, 4 should have it's own unshared irq) switched cards Realtek -> Via Rhine (I know they aren't good cards but I don't own any others which aren't in use) I tried to disable acpi from boot prompt (does it work when acpi is compiled into the kernel?) Nothing worked. Thanks for help. Greetings, Kay Btw.: there were two more problems which aren't really urgend for me: 1. With scsi-adapter system won't boot (symbios logic chip) 2. Sometimes it seems shutdown was done before disks were unmounted properly ( I think I saw somebody else who had this problem) Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2-RC #14: Wed Dec 10 15:46:54 CET 2003 root_at_bippes.finkenkrug.ev:/usr/obj/usr/src/sys/bippes Preloaded elf kernel "/boot/kernel/kernel" at 0xc085d000. Table 'FACP' at 0x3ffec100 Table 'BOOT' at 0x3ffec040 Table 'APIC' at 0x3ffec080 MADT: Found table at 0x3ffec080 MP Configuration Table version 1.4 found at 0xc00f4a60 APIC: Using the MADT enumerator. MADT: Found CPU APIC ID 0 ACPI ID 0: enabled SMP: Added CPU 0 (AP) MADT: Found CPU APIC ID 1 ACPI ID 1: enabled SMP: Added CPU 1 (AP) ACPI APIC Table: <ASUS A7M266-D> Calibrating clock(s) ... i8254 clock: 1193128 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 1613197472 Hz CPU: AMD Athlon(TM) XP 1900+ (1613.20-MHz 686-class CPU) Origin = "AuthenticAMD" Id = 0x662 Stepping = 2 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> AMD Features=0xc0480000<MP,AMIE,DSP,3DNow!> Data TLB: 32 entries, fully associative Instruction TLB: 16 entries, fully associative L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L2 internal cache: 256 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative real memory = 1073659904 (1023 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c29000 - 0x000000003edc5fff, 1041879040 bytes (254365 pages) avail memory = 1033506816 (985 MB) APIC ID: physical 0, logical 0:0 APIC ID: physical 1, logical 0:1 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 APIC: CPU 0 has ACPI ID 0 APIC: CPU 1 has ACPI ID 1 bios32: Found BIOS32 Service Directory header at 0xc00f1430 bios32: Entry = 0xf0bf0 (c00f0bf0) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0xdf0 pnpbios: Found PnP BIOS data at 0xc00fbfc0 pnpbios: Entry = f0000:bff0 Rev = 1.0 pnpbios: OEM ID cd041 Other BIOS signatures found: MADT: Found IO APIC ID 2, Vector 0 at 0xfec00000 ioapic0: intpin 0 -> ExtINT (edge, activehi) ioapic0: intpin 1 -> irq 1 (edge, activehi) ioapic0: intpin 2 -> irq 2 (edge, activehi) ioapic0: intpin 3 -> irq 3 (edge, activehi) ioapic0: intpin 4 -> irq 4 (edge, activehi) ioapic0: intpin 5 -> irq 5 (edge, activehi) ioapic0: intpin 6 -> irq 6 (edge, activehi) ioapic0: intpin 7 -> irq 7 (edge, activehi) ioapic0: intpin 8 -> irq 8 (edge, activehi) ioapic0: intpin 9 -> irq 9 (edge, activehi) ioapic0: intpin 10 -> irq 10 (edge, activehi) ioapic0: intpin 11 -> irq 11 (edge, activehi) ioapic0: intpin 12 -> irq 12 (edge, activehi) ioapic0: intpin 13 -> irq 13 (edge, activehi) ioapic0: intpin 14 -> irq 14 (edge, activehi) ioapic0: intpin 15 -> irq 15 (edge, activehi) ioapic0: intpin 16 -> irq 16 (level, activelo) ioapic0: intpin 17 -> irq 17 (level, activelo) ioapic0: intpin 18 -> irq 18 (level, activelo) ioapic0: intpin 19 -> irq 19 (level, activelo) ioapic0: intpin 20 -> irq 20 (level, activelo) ioapic0: intpin 21 -> irq 21 (level, activelo) ioapic0: intpin 22 -> irq 22 (level, activelo) ioapic0: intpin 23 -> irq 23 (level, activelo) MADT: intr override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 ioapic0: intpin 2 trigger: edge ioapic0: intpin 2 polarity: active-hi MADT: intr override: source 9, irq 9 ioapic0: intpin 9 trigger: level ioapic0: intpin 9 polarity: active-lo lapic0: Routing NMI -> LINT1 lapic0: LINT1 trigger: edge lapic0: LINT1 polarity: active-hi lapic1: Routing NMI -> LINT1 lapic1: LINT1 trigger: edge lapic1: LINT1 polarity: active-hi ioapic0 <Version 1.1> irqs 0-23 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff null: <null device, zero device> random: <entropy source> mem: <memory & I/O> Pentium Pro MTRR support enabled VESA: information block 56 45 53 41 00 02 61 6d 00 c0 01 00 00 00 0b 6a 00 c0 00 02 06 01 76 6d 00 c0 7d 6d 00 c0 89 6d 00 c0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 VESA: 11 mode(s) found VESA: v2.0, 32768k memory, flags:0x1, mode table:0xc00c6a0b (c0006a0b) VESA: Matrox Graphics Inc. VESA: Matrox Matrox G400 00 acpi0: <ASUS A7M266-D> on motherboard pci_open(1): mode 1 addr port (0x0cf8) is 0x80012814 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=700c1022) pcibios: BIOS version 2.10 Using $PIR table, 9 entries at 0xc00f1370 PCI-Only Interrupts: none Location Bus Device Pin Link IRQs embedded 0 7 B 0x01 3 4 5 7 9 10 11 12 embedded 0 7 C 0x02 3 4 5 7 9 10 11 12 embedded 0 7 D 0x03 3 4 5 7 9 10 11 12 slot 1 0 8 B 0x01 3 4 5 7 9 10 11 12 slot 1 0 8 C 0x02 3 4 5 7 9 10 11 12 slot 1 0 8 D 0x03 3 4 5 7 9 10 11 12 slot 2 0 9 A 0x01 3 4 5 7 9 10 11 12 slot 2 0 9 B 0x02 3 4 5 7 9 10 11 12 slot 2 0 9 C 0x03 3 4 5 7 9 10 11 12 slot 3 2 6 A 0x01 3 4 5 7 9 10 11 12 slot 3 2 6 B 0x02 3 4 5 7 9 10 11 12 slot 3 2 6 C 0x03 3 4 5 7 9 10 11 12 slot 4 2 5 A 0x02 3 4 5 7 9 10 11 12 slot 4 2 5 B 0x03 3 4 5 7 9 10 11 12 slot 4 2 5 D 0x01 3 4 5 7 9 10 11 12 slot 5 2 8 A 0x03 3 4 5 7 9 10 11 12 slot 5 2 8 C 0x01 3 4 5 7 9 10 11 12 slot 5 2 8 D 0x02 3 4 5 7 9 10 11 12 embedded 1 5 B 0x01 3 4 5 7 9 10 11 12 embedded 1 5 C 0x02 3 4 5 7 9 10 11 12 embedded 1 5 D 0x03 3 4 5 7 9 10 11 12 embedded 2 4 A 0x01 3 4 5 7 9 10 11 12 embedded 2 4 B 0x02 3 4 5 7 9 10 11 12 embedded 2 4 C 0x03 3 4 5 7 9 10 11 12 embedded 2 0 B 0x01 3 4 5 7 9 10 11 12 embedded 2 0 C 0x02 3 4 5 7 9 10 11 12 embedded 2 0 D 0x03 3 4 5 7 9 10 11 12 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 7 func 3 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 7 func 0 acpi0: Power Button (fixed) acpi0: Sleep Button (fixed) ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0xe408-0xe40b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_cpu1: <CPU> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 ---- initial configuration ------------------------ ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base fc000000, size 25, enabled map[14]: type 3, range 32, base fb800000, size 12, enabled map[18]: type 4, range 32, base 0000e800, size 2, port disabled found-> vendor=0x1022, dev=0x700c, revid=0x11 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2230, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x700d, revid=0x00 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0007, statreg=0x0220, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7440, revid=0x04 bus=0, slot=7, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000d800, size 4, enabled found-> vendor=0x1022, dev=0x7441, revid=0x04 bus=0, slot=7, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7443, revid=0x03 bus=0, slot=7, func=3 class=06-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7448, revid=0x04 bus=0, slot=16, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0017, statreg=0x2220, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) agp0: <AMD 762 host to AGP bridge> port 0xe800-0xe803 mem 0xfb800000-0xfb800fff,0xfc000000-0xfdffffff at device 0.0 on pci0 agp0: allocating GATT for aperture of size 32M agp0: gatt -> ag_pdir 0x28a000 agp0: allocating GATT for 8192 AGP page entries pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xe000-0xdfff pcib1: memory decode 0xf6800000-0xf7dfffff pcib1: prefetched decode 0xf7f00000-0xfb7fffff ---- initial configuration ------------------------ ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 map[10]: type 3, range 32, base f8000000, size 25, enabled map[14]: type 1, range 32, base f7000000, size 14, enabled map[18]: type 1, range 32, base f6800000, size 23, enabled pcib1: matched entry for 1.5.INTA (source ) pcib1: device is hardwired to IRQ 16 found-> vendor=0x102b, dev=0x0525, revid=0x05 bus=1, slot=5, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x10 (4000 ns), maxlat=0x20 (8000 ns) intpin=a, irq=16 powerspec 2 supports D0 D3 current D0 drm0: <Matrox G400/G450 (AGP)> mem 0xf6800000-0xf6ffffff,0xf7000000-0xf7003fff,0xf8000000-0xf9ffffff irq 16 at device 5.0 on pci1 info: [drm] AGP at 0xfc000000 32MB info: [drm] Initialized mga 3.1.0 20021029 on minor 0 isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <AMD 768 UDMA100 controller> port 0xd800-0xd80f at device 7.1 on pci0 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: reset tp1 mask=03 ostat0=50 ostat1=50 ata1-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata1-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata1-slave: stat=0x00 err=0x01 lsb=0x14 msb=0xeb ata1: reset tp2 mask=03 stat0=50 stat1=00 devices=0x9<ATAPI_SLAVE,ATA_MASTER> ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) pcib2: <ACPI PCI-PCI bridge> at device 16.0 on pci0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0xc000-0xcfff pcib2: memory decode 0xf5000000-0xf67fffff pcib2: prefetched decode 0xf7e00000-0xf7efffff pcib2: could not get PCI interrupt routing table for \\_SB_.PCI0.OP2P - AE_NOT_FOUND pci2: <ACPI PCI bus> on pcib2 pci2: physical bus=2 map[10]: type 4, range 32, base 0000c800, size 8, enabled found-> vendor=0x13f6, dev=0x0111, revid=0x10 bus=2, slot=4, func=0 class=04-01-00, hdrtype=0x00, mfdev=0 cmdreg=0x0085, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x02 (500 ns), maxlat=0x18 (6000 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 4, range 32, base 0000c400, size 8, enabled map[14]: type 1, range 32, base f5800000, size 8, enabled found-> vendor=0x10ec, dev=0x8139, revid=0x10 bus=2, slot=6, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 4, range 32, base 0000c000, size 8, enabled map[14]: type 1, range 32, base f5000000, size 8, enabled found-> vendor=0x1106, dev=0x3065, revid=0x43 bus=2, slot=8, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0097, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x03 (750 ns), maxlat=0x08 (2000 ns) intpin=a, irq=4 powerspec 2 supports D0 D3 current D0 pcm0: <CMedia CMI8738> port 0xc800-0xc8ff irq 10 at device 4.0 on pci2 pcib2: device pcm0 requested decoded I/O range 0xc800-0xc8ff pcm0: sndbuf_setmap 2ba000, 4000; 0xe3ef8000 -> 2ba000 pcm0: sndbuf_setmap 2d4000, 4000; 0xe3efc000 -> 2d4000 pcib2: device rl0 requested decoded I/O range 0xc400-0xc4ff rl0: <RealTek 8139 10/100BaseTX> port 0xc400-0xc4ff mem 0xf5800000-0xf58000ff irq 10 at device 6.0 on pci2 pcib2: device rl0 requested decoded I/O range 0xc400-0xc4ff rl0: Ethernet address: 00:c0:df:01:9c:ca miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl0: bpf attached vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xc000-0xc0ff mem 0xf5000000-0xf50000ff irq 4 at device 8.0 on pci2 pcib2: device vr0 requested decoded I/O range 0xc000-0xc0ff vr0: Ethernet address: 00:05:5d:a2:70:1c miibus1: <MII bus> on vr0 ukphy0: <Generic IEEE 802.3u media interface> on miibus1 ukphy0: OUI 0x0005be, model 0x0008, rev. 0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto vr0: bpf attached mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) unknown: not probed (disabled) fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 unknown: not probed (disabled) ppc0: using extended I/O port range ppc0: ECP SPP ECP+EPP SPP ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 plip0: bpf attached lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000 psm0: unable to allocate IRQ psmcpnp0 irq 12 on acpi0 psm0: current command byte:0047 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model MouseMan+, device ID 0-35, 3 buttons psm0: config:00000000, flags:00000000, packet size:3 psm0: syncmask:08, syncbits:08 unknown: not probed (disabled) mss_detect, busy still set (0xff) mss_detect, busy still set (0xff) mss_detect, busy still set (0xff) mss_detect, busy still set (0xff) mss_detect, busy still set (0xff) mss_detect, busy still set (0xff) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it ppc: ppc0 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0xe0c1 0xe0c1 0xe0c1 0xe0c1 sio0: probe failed test(s): 0 1 2 4 6 7 9 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 or not responding sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0xe0c1 0xe0c1 0xe0c1 0xe0c1 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x700ff fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered Timecounter "TSC" frequency 1613197472 Hz quality -100 Timecounters tick every 10.000 msec lo0: bpf attached ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata0-master: setting PIO4 on AMD 768 chip ata0-master: setting UDMA100 on AMD 768 chip GEOM: create disk ad0 dp=0xc6b44d60 ad0: <ST380020A/3.39> ATA-6 disk at ata0-master ad0: 76319MB (156301488 sectors), 155061 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, UDMA100 GEOM: new disk ad0 ata1-slave: pio=0x0c wdma=0x22 udma=0x42 cable=40pin ata1-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata1-master: setting PIO4 on AMD 768 chip ata1-master: setting UDMA100 on AMD 768 chip ata1-slave: setting PIO4 on AMD 768 chip GEOM: create disk ad2 dp=0xc6b44c60 ad2: <ST340810A/3.39> ATA-6 disk at ata1-master ad2: 38166MB (78165360 sectors), 77545 C, 16 H, 63 S, 512 B ad2: 16 secs/int, 1 depth queue, UDMA100 acd0: <YAMAHA CRW-F1E/1.0d> CDRW drive at ata1 as slave acd0: read 7580KB/s (7580KB/s) write 7580KB/s (7580KB/s), 8192KB buffer, PIO4 acd0: Reads: CDR, CDRW, CDDA stream, packet acd0: Writes: CDR, CDRW, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: CD-ROM unknown [0] f:00 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:83875302 [1] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:83875365 l:40949685 [2] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:124825050 l:31471335 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad0s1, start 32256 length 42944154624 end 42944186879 GEOM: Configure ad0s2, start 42944186880 length 20966238720 end 63910425599 GEOM: Configure ad0s3, start 63910425600 length 16113323520 end 80023749119 GEOM: new disk ad2 GEOM: Configure ad0s1a, start 39846469632 length 1073741824 end 40920211455 GEOM: Configure ad0s1b, start 134217728 length 2131288064 end 2265505791 GEOM: Configure ad0s1c, start 0 length 42944154624 end 42944154623 GEOM: Configure ad0s1e, start 2265505792 length 37580963840 end 39846469631 GEOM: Configure ad0s1f, start 40920211456 length 1073741824 end 41993953279 GEOM: Configure ad0s1g, start 41993953280 length 943718400 end 42937671679 GEOM: Configure ad0s2c, start 0 length 20966238720 end 20966238719 GEOM: Configure ad0s2e, start 0 length 20966238720 end 20966238719 GEOM: Configure ad0s3a, start 0 length 1073741824 end 1073741823 GEOM: Configure ad0s3b, start 1073741824 length 2147483648 end 3221225471 GEOM: Configure ad0s3c, start 0 length 16113323520 end 16113323519 GEOM: Configure ad0s3d, start 3221225472 length 1073741824 end 4294967295 GEOM: Configure ad0s3e, start 4294967296 length 1073741824 end 5368709119 GEOM: Configure ad0s3f, start 5368709120 length 10744614400 end 16113323519 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:78156162 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad2s1, start 32256 length 40015954944 end 40015987199 GEOM: Configure ad2s1c, start 0 length 40015954944 end 40015954943 GEOM: Configure ad2s1d, start 0 length 40015954944 end 40015954943 (probe0:ata0:0:0:0): error 22 (probe0:ata0:0:0:0): Unretryable Error (probe1:ata0:0:1:0): error 22 (probe1:ata0:0:1:0): Unretryable Error (probe2:ata1:0:0:0): error 22 (probe2:ata1:0:0:0): Unretryable Error (probe0:ata0:0:0:0): error 22 (probe0:ata0:0:0:0): Unretryable Error (probe1:ata0:0:1:0): error 22 (probe1:ata0:0:1:0): Unretryable Error (probe2:ata1:0:0:0): error 22 (probe2:ata1:0:0:0): Unretryable Error GEOM: create disk cd0 dp=0xc6970e00 pass0 at ata1 bus 0 target 1 lun 0 pass0: <YAMAHA CRW-F1E 1.0d> Removable CD-ROM SCSI-2 device pass0: Serial Number ' pass0: 16.000MB/s transfers (cd0:ata1:0:1:0): Retrying Command GEOM: new disk cd0 (cd0:ata1:0:1:0): error 6 (cd0:ata1:0:1:0): Unretryable Error cd0 at ata1 bus 0 target 1 lun 0 cd0: <YAMAHA CRW-F1E 1.0d> Removable CD-ROM SCSI-2 device cd0: Serial Number ' cd0: 16.000MB/s transfers cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x01000000 VER: 0x00040010 LDR: 0x02000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff ioapic0: routing intpin 1 (IRQ 1) to cluster 0 ioapic0: routing intpin 4 (IRQ 4) to cluster 0 ioapic0: routing intpin 6 (IRQ 6) to cluster 0 ioapic0: routing intpin 7 (IRQ 7) to cluster 0 ioapic0: routing intpin 8 (IRQ 8) to cluster 0 ioapic0: routing intpin 9 (IRQ 9) to cluster 0 ioapic0: routing intpin 10 (IRQ 10) to cluster 0 ioapic0: routing intpin 12 (IRQ 12) to cluster 0 ioapic0: routing intpin 13 (IRQ 13) to cluster 0 ioapic0: routing intpin 14 (IRQ 14) to cluster 0 ioapic0: routing intpin 15 (IRQ 15) to cluster 0 (cd0:ata1:0:1:0): Retrying Command (cd0:ata1:0:1:0): error 6 (cd0:ata1:0:1:0): Unretryable Error (cd0:ata1:0:1:0): Retrying Command (cd0:ata1:0:1:0): error 6 (cd0:ata1:0:1:0): Unretryable Error Mounting root from ufs:/dev/ad0s3a start_init: trying /sbin/init Loading configuration files. Entropy harvesting: interrupts ethernet point_to_point . swapon: adding /dev/ad0s3b as swap device Starting file system checks: /dev/ad0s3a: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ad0s3a: clean, 350419 free (675 frags, 43718 blocks, 0.1% fragmentation) /dev/ad2s1d: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ad2s1d: clean, 6584724 free (126580 frags, 807268 blocks, 0.7% fragmentation) /dev/ad0s3d: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ad0s3d: clean, 485574 free (150 frags, 60678 blocks, 0.0% fragmentation) /dev/ad0s3e: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ad0s3e: clean, 438351 free (1143 frags, 54651 blocks, 0.2% fragmentation) /dev/ad0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ad0s1a: clean, 371857 free (241 frags, 46452 blocks, 0.0% fragmentation) /dev/ad0s1e: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ad0s1e: clean, 6701033 free (114441 frags, 823324 blocks, 0.6% fragmentation) /dev/ad0s1f: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ad0s1f: clean, 462471 free (2375 frags, 57512 blocks, 0.5% fragmentation) /dev/ad0s3f: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ad0s3f: clean, 2472474 free (50418 frags, 302757 blocks, 1.0% fragmentation) /dev/ad0s2e: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ad0s2e: clean, 3050554 free (626 frags, 381241 blocks, 0.0% fragmentation) Linux ELF exec handler installed linprocfs registered Setting hostname: bippes.finkenkrug.ev. rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=8<VLAN_MTU> inet 192.168.1.3 netmask 0xffffff00 broadcast 192.168.1.255 inet6 fe80::2c0:dfff:fe01:9cca%rl0 prefixlen 64 tentative scopeid 0x1 ether 00:c0:df:01:9c:ca media: Ethernet autoselect (none) status: no carrier lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 ipfw2 initialized, divert disabled, rule-based forwarding enabled, default to deny, logging disabled Flushed all rules. 00100 allow ip from any to any via lo0 00200 deny ip from any to 127.0.0.0/8 00300 deny ip from 127.0.0.0/8 to any 65000 allow ip from any to any Firewall rules loaded, starting divert daemons: . net.inet.ip.fw.enable: 1 -> 1 add net default: gateway 192.168.1.2 Additional routing options: . hw.bus.devctl_disable: 0 -> 1 Mounting NFS file systems: . Starting syslogd. Dec 12 08:00:17 bippes syslogd: kernel boot file is /boot/kernel/kernel ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout /usr/X11R6/lib/aout Starting local daemons: . Updating motd . Configuring syscons: blanktime allscreens . Starting sshd. rl0: watchdog timeout Initial i386 initialization: . Additional ABI support: linux rl0: watchdog timeout . Starting cron. Local package initialization: rl0: watchdog timeout cups: started scheduler. mysqld rtc WARNING: driver "rtc" used unreserved major device number 202 link_elf: symbol cpu_apic_address undefined kldload: can't load /usr/local/lib/vmware/lib/modules/vmmon_smp.ko : No such file or directory vmnet1: bpf attached VMware . Local package initialization: cups: started scheduler. mysqld rtc kldload: can't load /usr/local/modules/rtc.ko : File exists link_elf: symbol cpu_apic_address undefined kldload: can't load /usr/local/lib/vmware/lib/modules/vmmon_smp.ko : No such file or directory VMware . Additional TCP options: . Additional TCP options: . route: writing to routing socket : File exists add net default: gateway 192.168.1.2: File exists Additional routing options: . Starting background file system checks in 60 seconds. Fri Dec 12 08:00:38 CET 2003 rl0: watchdog timeout Dec 12 08:00:42 bippes login: ROOT LOGIN (root) ON ttyv0 rl0: watchdog timeoutReceived on Thu Dec 11 2003 - 22:51:42 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:33 UTC