Hi, I'm having trouble booting today's current. The kernel hangs after various messages such as: ad0: WARNING - SETFEATURES recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad0: WARNING - SET_MULTI recovered from missing interrupt I've tried disabling acpi and ata_dma with no effect. I can still break into the debugger, but as it is not a panic I don't know what help that is. Last running kernel is from Fri Oct 3 00:28:37 CEST 2003 which I think is post atang, but I'm not sure. Any tips are welcome. Full log of boot -v follows. -CJ Console: serial port BIOS drive A: is disk0 BIOS drive C: is disk1 BIOS drive D: is disk2 BIOS 639kB/228288kB available memory FreeBSD/i386 bootstrap loader, Revision 1.1 (cjv_at_dent.vdbonline.com, Wed Jun 25 00:18:04 CEST 2003) Loading /boot/defaults/loader.conf /boot/kernel/kernel text=0x4c0898 data=0x79fec+0x64c10 syms=[0x4+0x5a4f0+0x4 +0x6eb3a] /boot/kernel/vesa.ko text=0x39d8 data=0x2a0+0x27c syms=[0x4+0x850+0x4+0x709] /boot/kernel/snd_pcm.ko text=0x14cb8 data=0x2288+0x10c4 syms=[0x4+0x2bc0+0x4 +0x30f0] /boot/kernel/snd_emu10k1.ko text=0x4ffc data=0x61c+0x4 syms=[0x4+0xbe0+0x4 +0xc12] Loading /boot/defaults/loader.conf Hit [Enter] to boot immediately, or any other key for command prompt. Type '?' for a list of commands, 'help' for more detailed help. OK boot -v SMAP type=01 base=0000000000000000 len=000000000009fc00 SMAP type=02 base=000000000009fc00 len=0000000000000400 SMAP type=02 base=00000000000f0000 len=0000000000010000 SMAP type=02 base=00000000ffff0000 len=0000000000010000 SMAP type=01 base=0000000000100000 len=000000000def0000 SMAP type=03 base=000000000dff3000 len=000000000000d000 SMAP type=04 base=000000000dff0000 len=0000000000003000 Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.1-CURRENT #0: Thu Nov 13 17:03:39 CET 2003 root_at_dent.vdbonline.com:/usr/obj/usr/src/sys/BEEBELBROX Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a97000. Preloaded elf module "/boot/kernel/vesa.ko" at 0xc0a97200. Preloaded elf module "/boot/kernel/snd_pcm.ko" at 0xc0a972ac. Preloaded elf module "/boot/kernel/snd_emu10k1.ko" at 0xc0a97358. Calibrating clock(s) ... i8254 clock: 1193256 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 499781229 Hz CPU: Pentium II/Pentium II Xeon/Celeron (499.78-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x665 Stepping = 5 Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR> real memory = 234815488 (223 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c29000 - 0x000000000dbd9fff, 217780224 bytes (53169 pages) avail memory = 218529792 (208 MB) bios32: Found BIOS32 Service Directory header at 0xc00fafb0 bios32: Entry = 0xfb430 (c00fb430) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0xb460 pnpbios: Found PnP BIOS data at 0xc00fc000 pnpbios: Entry = f0000:c028 Rev = 1.0 Other BIOS signatures found: wlan: <802.11 Link Layer> null: <null device, zero device> random: <entropy source> mem: <memory & I/O> Pentium Pro MTRR support enabled VESA: information block 56 45 53 41 00 03 00 01 00 01 01 00 00 00 22 00 00 01 40 00 05 02 07 01 00 01 0e 01 00 01 17 01 00 01 00 01 01 01 02 01 03 01 04 01 05 01 06 01 07 01 08 01 09 01 0a 01 0b 01 0c 01 0e 01 0f 01 VESA: 33 mode(s) found VESA: v3.0, 4096k memory, flags:0x1, mode table:0xc0a6ece2 (1000022) VESA: NVidia VESA: NVidia Riva TNT B1 acpi0: <AWARD AWRDACPI> on motherboard pci_open(1): mode 1 addr port (0x0cf8) is 0x80005810 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086) pcibios: BIOS version 2.10 Using $PIR table, 7 entries at 0xc00fdf00 PCI-Only Interrupts: 5 9 10 11 Location Bus Device Pin Link IRQs slot 1 0 15 A 0x60 3 4 5 7 9 10 11 12 14 15 slot 1 0 15 B 0x61 3 4 5 7 9 10 11 12 14 15 slot 1 0 15 C 0x62 3 4 5 7 9 10 11 12 14 15 slot 1 0 15 D 0x63 3 4 5 7 9 10 11 12 14 15 slot 2 0 13 A 0x61 3 4 5 7 9 10 11 12 14 15 slot 2 0 13 B 0x62 3 4 5 7 9 10 11 12 14 15 slot 2 0 13 C 0x63 3 4 5 7 9 10 11 12 14 15 slot 2 0 13 D 0x60 3 4 5 7 9 10 11 12 14 15 slot 3 0 11 A 0x62 3 4 5 7 9 10 11 12 14 15 slot 3 0 11 B 0x63 3 4 5 7 9 10 11 12 14 15 slot 3 0 11 C 0x60 3 4 5 7 9 10 11 12 14 15 slot 3 0 11 D 0x61 3 4 5 7 9 10 11 12 14 15 slot 4 0 9 A 0x63 3 4 5 7 9 10 11 12 14 15 slot 4 0 9 B 0x60 3 4 5 7 9 10 11 12 14 15 slot 4 0 9 C 0x61 3 4 5 7 9 10 11 12 14 15 slot 4 0 9 D 0x62 3 4 5 7 9 10 11 12 14 15 slot 5 0 17 A 0x63 3 4 5 7 9 10 11 12 14 15 slot 5 0 17 B 0x60 3 4 5 7 9 10 11 12 14 15 slot 5 0 17 C 0x61 3 4 5 7 9 10 11 12 14 15 slot 5 0 17 D 0x62 3 4 5 7 9 10 11 12 14 15 embedded 0 7 A 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 7 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 7 C 0x62 3 4 5 7 9 10 11 12 14 15 embedded 0 7 D 0x63 3 4 5 7 9 10 11 12 14 15 embedded 0 1 A 0x60 3 4 5 7 9 10 11 12 14 15 embedded 0 1 B 0x61 3 4 5 7 9 10 11 12 14 15 embedded 0 1 C 0x62 3 4 5 7 9 10 11 12 14 15 embedded 0 1 D 0x63 3 4 5 7 9 10 11 12 14 15 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 7 func 0 acpi0: Power Button (fixed) ACPI timer looks BAD min = 2, max = 5, width = 3 ACPI timer looks BAD min = 2, max = 16777213, width = 16777211 ACPI timer looks BAD min = 2, max = 5, width = 3 ACPI timer looks BAD min = 2, max = 5, width = 3 ACPI timer looks BAD min = 1, max = 5, width = 4 ACPI timer looks BAD min = 1, max = 5, width = 4 ACPI timer looks BAD min = 2, max = 5, width = 3 ACPI timer looks BAD min = 2, max = 5, width = 3 ACPI timer looks BAD min = 2, max = 5, width = 3 ACPI timer looks BAD min = 1, max = 5, width = 4 Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0x5000-0x500f,0x4000-0x4041,0xcf8-0xcff on acpi0 ---- initial configuration ------------------------ \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.0 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.1 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.2 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.3 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.0 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.1 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.2 \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.3 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.0 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.1 \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.2 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.3 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.0 \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.1 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.2 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.3 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.0 \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.1 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.2 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.3 \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.0 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.1 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.2 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.3 \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.0 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.1 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.2 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.3 ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.0 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.1 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.2 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.15.3 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.0 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.1 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.2 \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.13.3 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.0 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.1 \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.2 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.11.3 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.0 \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.1 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.2 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.9.3 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.0 \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.1 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.2 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.17.3 \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.0 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.1 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.2 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.7.3 \_SB_.PCI0.ISA_.LNKA irq 10: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.0 \_SB_.PCI0.ISA_.LNKB irq 5: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.1 \_SB_.PCI0.ISA_.LNKC irq 9: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.2 \_SB_.PCI0.ISA_.LNKD irq 11: [ 3 4 5 6 7 10 11 12 14 15] low,level,sharable 0.1.3 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base e0000000, size 26, enabled found-> vendor=0x8086, dev=0x7190, revid=0x03 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2210, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x7191, revid=0x03 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0220, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x88 (34000 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x7110, revid=0x02 bus=0, slot=7, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000f000, size 4, enabled found-> vendor=0x8086, dev=0x7111, revid=0x01 bus=0, slot=7, func=1 class=01-01-80, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000a000, size 5, enabled pcib0: matched entry for 0.7.INTD (source \_SB_.PCI0.ISA_.LNKD) pcib0: slot 7 INTD is routed to irq 11 found-> vendor=0x8086, dev=0x7112, revid=0x01 bus=0, slot=7, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=11 map[90]: type 4, range 32, base 00005000, size 4, enabled found-> vendor=0x8086, dev=0x7113, revid=0x02 bus=0, slot=7, func=3 class=06-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 1, range 32, base ec000000, size 12, enabled map[14]: type 4, range 32, base 0000a400, size 8, enabled pcib0: matched entry for 0.9.INTA (source \_SB_.PCI0.ISA_.LNKD) pcib0: slot 9 INTA is routed to irq 11 found-> vendor=0x1050, dev=0x6692, revid=0x01 bus=0, slot=9, func=0 class=02-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0003, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 map[10]: type 4, range 32, base 0000a800, size 7, enabled map[14]: type 1, range 32, base ec001000, size 7, enabled pcib0: matched entry for 0.11.INTA (source \_SB_.PCI0.ISA_.LNKC) pcib0: slot 11 INTA is routed to irq 9 found-> vendor=0x10b7, dev=0x9200, revid=0x74 bus=0, slot=11, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns) intpin=a, irq=9 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base e9000000, size 24, enabled pcib0: matched entry for 0.13.INTA (source \_SB_.PCI0.ISA_.LNKB) pcib0: slot 13 INTA is routed to irq 5 found-> vendor=0x14f1, dev=0x8800, revid=0x03 bus=0, slot=13, func=0 class=04-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0006, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x14 (5000 ns), maxlat=0x37 (13750 ns) intpin=a, irq=5 powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base ea000000, size 24, enabled pcib0: matched entry for 0.13.INTA (source \_SB_.PCI0.ISA_.LNKB) pcib0: slot 13 INTA is routed to irq 5 found-> vendor=0x14f1, dev=0x8811, revid=0x03 bus=0, slot=13, func=1 class=04-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0006, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0xff (63750 ns) intpin=a, irq=5 powerspec 2 supports D0 D3 current D0 map[10]: type 4, range 32, base 0000ac00, size 3, enabled map[14]: type 4, range 32, base 0000b000, size 2, enabled map[18]: type 4, range 32, base 0000b400, size 3, enabled map[1c]: type 4, range 32, base 0000b800, size 2, enabled map[20]: type 4, range 32, base 0000bc00, size 4, enabled pcib0: matched entry for 0.15.INTA (source \_SB_.PCI0.ISA_.LNKA) pcib0: slot 15 INTA is routed to irq 10 found-> vendor=0x1095, dev=0x0649, revid=0x02 bus=0, slot=15, func=0 class=01-04-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 4, range 32, base 0000c000, size 5, enabled pcib0: matched entry for 0.17.INTA (source \_SB_.PCI0.ISA_.LNKD) pcib0: slot 17 INTA is routed to irq 11 found-> vendor=0x1102, dev=0x0002, revid=0x04 bus=0, slot=17, func=0 class=04-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x02 (500 ns), maxlat=0x14 (5000 ns) intpin=a, irq=11 powerspec 1 supports D0 D3 current D0 map[10]: type 4, range 32, base 0000c400, size 3, enabled found-> vendor=0x1102, dev=0x7002, revid=0x01 bus=0, slot=17, func=1 class=09-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 1 supports D0 D3 current D0 agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0 agp0: allocating GATT for aperture of size 64M pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0x9000-0x9fff pcib1: memory decode 0xe4000000-0xe5ffffff pcib1: prefetched decode 0xe6000000-0xe7ffffff pci1: <PCI bus> on pcib1 pci1: physical bus=1 map[10]: type 1, range 32, base e4000000, size 24, enabled map[14]: type 3, range 32, base e6000000, size 25, enabled pcib0: matched entry for 0.1.INTA (source \_SB_.PCI0.ISA_.LNKA) pcib0: slot 1 INTA is routed to irq 10 pcib1: slot 0 INTA is routed to irq 10 found-> vendor=0x10de, dev=0x0029, revid=0x11 bus=1, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns) intpin=a, irq=10 powerspec 1 supports D0 D3 current D0 pci1: <display, VGA> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 UDMA33 controller> port 0xf000-0xf00f at device 7.1 on pci0 ata0: reset tp1 mask=03 ostat0=50 ostat1=50 ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb ata0-slave: stat=0x00 err=0x01 lsb=0x14 msb=0xeb ata0: reset tp2 mask=03 stat0=00 stat1=00 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER> ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: reset tp1 mask=03 ostat0=00 ostat1=00 ata1-master: stat=0x00 err=0x00 lsb=0x00 msb=0x00 ata1-slave: stat=0x00 err=0x00 lsb=0x00 msb=0x00 ata1: reset tp2 mask=03 stat0=00 stat1=00 devices=0x0 ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xa000-0xa01f irq 11 at device 7.2 on pci0 usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered ulpt0: Hewlett-Packard DeskJet 3820, rev 1.10/1.00, addr 2, iclass 7/1 ulpt0: using bi-directional mode pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) pci0: <network> at device 9.0 (no driver attached) xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xa800-0xa87f mem 0xec001000-0xec00107f irq 9 at device 11.0 on pci0 xl0: using memory mapped I/O xl0: Ethernet address: 00:50:da:e2:8a:2d xl0: media options word: a xl0: found MII/AUTO miibus0: <MII bus> on xl0 xlphy0: <3c905C 10/100 internal PHY> on miibus0 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl0: bpf attached pci0: <multimedia, video> at device 13.0 (no driver attached) pci0: <multimedia> at device 13.1 (no driver attached) atapci1: <CMD 649 UDMA100 controller> port 0xbc00-0xbc0f,0xb800-0xb803,0xb400-0xb407,0xb000-0xb003,0xac00-0xac07 irq 10 at device 15.0 on pci0 atapci1: [MPSAFE] ata2: reset tp1 mask=03 ostat0=50 ostat1=50 ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata2-slave: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata2: reset tp2 mask=03 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER> ata2: at 0xac00 on atapci1 ata2: [MPSAFE] ata3: reset tp1 mask=03 ostat0=7f ostat1=7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-master: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f ata3: reset tp2 mask=00 stat0=ff stat1=ff devices=0x0 ata3: at 0xb400 on atapci1 ata3: [MPSAFE] pcm0: <Creative EMU10K1> port 0xc000-0xc01f irq 11 at device 17.0 on pci0 emu: setmap (d71e000, 800), nseg=1, error=0 emu: setmap (d81f000, 1000), nseg=1, error=0 pcm0: <TriTech TR28023 AC97 Codec (id = 0x54524103)> pcm0: Codec features 6 bit master volume, no 3D Stereo Enhancement emu: setmap (d801000, 1000), nseg=1, error=0 emu: setmap (d783000, 1000), nseg=1, error=0 emu: setmap (d55c000, 1000), nseg=1, error=0 emu: setmap (d31a000, 1000), nseg=1, error=0 pcm0: sndbuf_setmap d4d8000, 1000; 0xc2a24000 -> d4d8000 pcm0: sndbuf_setmap d696000, 1000; 0xc2a22000 -> d696000 fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f2-0x3f5 irq 6 drq 2 on acpi0 sio0: irq maps: 0x801 0x811 0x801 0x801 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A, console sio1: irq maps: 0x801 0x809 0x801 0x801 sio1 port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ppc0: using extended I/O port range ppc0: SPP ppc0 port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 plip0: bpf attached lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 unknown: not probed (disabled) psmcpnp0 irq 12 on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000 psm0: current command byte:0047 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fa kbdc: RESET_AUX status:00aa kbdc: RESET_AUX ID:0000 kbdc: RESET_AUX return code:00fa kbdc: RESET_AUX status:00aa kbdc: RESET_AUX ID:0000 psm: status 00 02 64 psm: status 1a 03 c8 psm: status 1a 03 c8 psm: status 1a 03 c8 psm: data c8 c6 51 psm: data e8 f2 30 psm: status 00 02 64 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model MouseMan+, device ID 0-51, 3 buttons psm0: config:00000000, flags:00000000, packet size:3 psm0: syncmask:08, syncbits:08 unknown: not probed (disabled) npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it ppc: ppc0 already exists; skipping it sio: sio0 already exists; skipping it sio: sio1 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff ex_isa_identify() sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <Option ROMs> at iomem 0xd1000-0xd37ff,0xd0000-0xd07ff,0xc0000-0xcffff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) fb: new array size 4 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x100> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x700ff fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 01 0f 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered Timecounter "TSC" frequency 499781229 Hz quality 800 Timecounters tick every 10.000 msec lo0: bpf attached acpi_cpu0: set speed to 100.0% acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% ata0-slave: pio=0x0c wdma=0x22 udma=0xffffffff cable=40pin ata0-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin ata0-master: setting PIO4 on Intel PIIX4 chip ata0-master: setting UDMA33 on Intel PIIX4 chip ata0-slave: setting PIO4 on Intel PIIX4 chip ata0-slave: setting WDMA2 on Intel PIIX4 chip acd0: <TDK CDRW4800B/S7S4> CDRW drive at ata0 as master acd0: read 8250KB/s (8250KB/s) write 172KB/s (8250KB/s), 2048KB buffer, UDMA33 acd0: Reads: CDR, CDRW, CDDA stream, packet acd0: Writes: CDR, CDRW, test write, burnproof acd0: Audio: play, 255 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc acd1: <CREATIVEDVD-ROM DVD2240E 08/23/97/1.0A> DVDROM drive at ata0 as slave acd1: read 4125KB/s (4125KB/s), 256KB buffer, WDMA2 acd1: Reads: CDR, CDRW, CDDA, DVDROM, packet acd1: Writes: acd1: Audio: play, 255 volume levels acd1: Mechanism: ejectable tray, unlocked acd1: Medium: no/blank disc ata2-slave: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata2-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata2-master: WARNING - SETFEATURES recovered from missing interrupt ata2-master: setting PIO4 on CMD 649 chip ata2-slave: WARNING - SETFEATURES recovered from missing interrupt ata2-slave: setting PIO4 on CMD 649 chip ad0: WARNING - SETFEATURES recovered from missing interrupt ad0: WARNING - SETFEATURES recovered from missing interrupt ad0: WARNING - SET_MULTI recovered from missing interrupt GEOM: create disk ad0 dp=0xc2a9ae60 ad0: <IC35L020AVER07-0/ER2OA44A> ATA-5 disk at ata2-master ad0: 19623MB (40188960 sectors), 39870 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, PIO4 GEOM: new disk ad0 ad0: WARNING - READ_MUL recovered from missing interrupt ar: FreeBSD check1 failed ad0: WARNING - READ_MUL recovered from missing interrupt [0] f:00 typ:7 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:16771797 [1] f:80 typ:165 s(CHS):1023/254/63 e(CHS):1023/254/63 s:16771860 l:16771860 [2] f:00 typ:131 s(CHS):1023/254/63 e(CHS):1023/254/63 s:33543720 l:6120765 [3] f:00 typ:130 s(CHS):1023/254/63 e(CHS):1023/254/63 s:39664485 l:514080 GEOM: Configure ad0s1, start 32256 length 8587160064 end 8587192319 GEOM: Configure ad0s2, start 8587192320 length 8587192320 end 17174384639 GEOM: Configure ad0s3, start 17174384640 length 3133831680 end 20308216319 GEOM: Configure ad0s4, start 20308216320 length 263208960 end 20571425279 ad1: WARNING - SETFEATURES recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad1: WARNING - SETFEATURES recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad1: WARNING - SET_MULTI recovered from missing interrupt GEOM: create disk ad1 dp=0xc2a9ab60 ad1: <Maxtor 5T040H4/TAH71DP0> ATA-6 disk at ata2-slave ad1: 39083MB (80043264 sectors), 79408 C, 16 H, 63 S, 512 B ad1: 16 secs/int, 1 depth queue, PIO4 ad0: WARNING - READ_MUL recovered from missing interrupt GEOM: Configure ad0s2a, start 0 length 268435456 end 268435455 GEOM: Configure ad0s2b, start 268435456 length 268435456 end 536870911 GEOM: Configure ad0s2c, start 0 length 8587192320 end 8587192319 GEOM: Configure ad0s2d, start 536870912 length 268435456 end 805306367 GEOM: Configure ad0s2e, start 805306368 length 268435456 end 1073741823 GEOM: Configure ad0s2f, start 1073741824 length 7513450496 end 8587192319 GEOM: new disk ad1 ar: FreeBSD read conf failed ad1: WARNING - READ_MUL recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad1: WARNING - READ_MUL recovered from missing interrupt [0] f:00 typ:1 s(CHS):2/0/1 e(CHS):3/254/63 s:32130 l:32130 [1] f:00 typ:7 s(CHS):4/0/1 e(CHS):1023/254/63 s:64260 l:29639925 [2] f:80 typ:165 s(CHS):1023/254/63 e(CHS):1023/254/63 s:29704185 l:50331645 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad1s1, start 16450560 length 16450560 end 32901119 GEOM: Configure ad1s2, start 32901120 length 15175641600 end 15208542719 GEOM: Configure ad1s3, start 15208542720 length 25769802240 end 40978344959 ad1: WARNING - READ_MUL recovered from missing interrupt ad1: WARNING - READ_MUL recovered from missing interrupt ad1: WARNING - READ_MUL recovered from missing interrupt GEOM: Configure ad1s3c, start 0 length 25769802240 end 25769802239 ad1: WARNING - READ_MUL recovered from missing interrupt Mounting root from ufs:/dev/ad0s2a ad0: WARNING - READ_MUL recovered from missing interrupt ad0: WARNING - READ_MUL recovered from missing interrupt ad0: TIMEOUT - READ_MUL retrying (2 retries left) ata2: resetting devices .. ata2: reset tp1 mask=03 ostat0=58 ostat1=50 ad0: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ad1: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata2: reset tp2 mask=03 stat0=50 stat1=50 devices=0x3<ATA_SLAVE,ATA_MASTER>Received on Thu Nov 13 2003 - 10:37:02 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:28 UTC