Re: PII SMP system hangs during boot with ACPI enabled

From: John Polstra <jdp_at_polstra.com>
Date: Mon, 24 Nov 2003 10:03:14 -0800 (PST)
On 24-Nov-2003 Nate Lawson wrote:
> Please add debug.acpi.disable="cpu" to loader.conf or type that in at the
> loader prompt.  If it boots ok, we'll have to debug the acpi_cpu_startup
> path.

Thanks.  It still hangs even with debug.acpi.disable="cpu".  I have
attached the verbose boot messages.  They are essentially the same as
the previous messages, except that the acpi_cpu messages are gone now
as expected.

If there's anything else I should try, just let me know.

John

SMAP type=01 base=0000000000000000 len=000000000009fc00
SMAP type=02 base=000000000009fc00 len=0000000000000400
SMAP type=02 base=00000000000e0000 len=0000000000020000
SMAP type=01 base=0000000000100000 len=000000000fee0000
SMAP type=03 base=000000000ffe0000 len=0000000000018000
SMAP type=04 base=000000000fff8000 len=0000000000008000
SMAP type=02 base=00000000fec00000 len=0000000000001000
SMAP type=02 base=00000000fee00000 len=0000000000001000
SMAP type=02 base=00000000fffc0000 len=0000000000040000
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.2-BETA #1: Sun Nov 23 13:32:22 PST 2003
    jdp_at_vashon.polstra.com:/usr/src/sys/i386/compile/VASHON
Preloaded elf kernel "/boot/kernel/kernel" at 0xc07bc000.
ACPI APIC Table: <TYANCP TYANTBLE>
Calibrating clock(s) ... i8254 clock: 1193039 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 400911753 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (400.91-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x652  Stepping = 2
  Features=0x183fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CM
OV,PAT,PSE36,MMX,FXSR>
real memory  = 268304384 (255 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000000829000 - 0x000000000fb39fff, 254873600 bytes (62225 pages)
avail memory = 255262720 (243 MB)
APIC ID: physical 0, logical 0:0
APIC ID: physical 1, logical 0:1
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
bios32: Found BIOS32 Service Directory header at 0xc00fdb40
bios32: Entry = 0xfdb50 (c00fdb50)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xdb71
pnpbios: Found PnP BIOS data at 0xc00f72c0
pnpbios: Entry = f0000:6964  Rev = 1.0
Other BIOS signatures found:
APIC: CPU 0 has ACPI ID 1
APIC: CPU 1 has ACPI ID 2
MADT: Found IO APIC ID 2, Vector 0 at 0xfec00000
ioapic0: intpin 0 -> ExtINT (edge, activehi)
ioapic0: intpin 1 -> irq 1 (edge, activehi)
ioapic0: intpin 2 -> irq 2 (edge, activehi)
ioapic0: intpin 3 -> irq 3 (edge, activehi)
ioapic0: intpin 4 -> irq 4 (edge, activehi)
ioapic0: intpin 5 -> irq 5 (edge, activehi)
ioapic0: intpin 6 -> irq 6 (edge, activehi)
ioapic0: intpin 7 -> irq 7 (edge, activehi)
ioapic0: intpin 8 -> irq 8 (edge, activehi)
ioapic0: intpin 9 -> irq 9 (edge, activehi)
ioapic0: intpin 10 -> irq 10 (edge, activehi)
ioapic0: intpin 11 -> irq 11 (edge, activehi)
ioapic0: intpin 12 -> irq 12 (edge, activehi)
ioapic0: intpin 13 -> irq 13 (edge, activehi)
ioapic0: intpin 14 -> irq 14 (edge, activehi)
ioapic0: intpin 15 -> irq 15 (edge, activehi)
ioapic0: intpin 16 -> irq 16 (level, activelo)
ioapic0: intpin 17 -> irq 17 (level, activelo)
ioapic0: intpin 18 -> irq 18 (level, activelo)
ioapic0: intpin 19 -> irq 19 (level, activelo)
ioapic0: intpin 20 -> irq 20 (level, activelo)
ioapic0: intpin 21 -> irq 21 (level, activelo)
ioapic0: intpin 22 -> irq 22 (level, activelo)
ioapic0: intpin 23 -> irq 23 (level, activelo)
MADT: intr override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 trigger: edge
ioapic0: intpin 2 polarity: active-hi
MADT: intr override: source 9, irq 20
ioapic0: intpin 9 disabled
ioapic0: intpin 20 trigger: level
ioapic0: intpin 20 polarity: active-hi
ioapic0 <Version 1.1> irqs 0-23 on motherboard
cpu0 BSP:
     ID: 0x00000000   VER: 0x00040011 LDR: 0x01000000 DFR: 0x0fffffff
  lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
null: <null device, zero device>
random: <entropy source>
mem: <memory & I/O>
Pentium Pro MTRR support enabled
acpi0: <TYANCP TYANTBLE> on motherboard
acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 20
pci_open(1):    mode 1 addr port (0x0cf8) is 0x8000005c
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=00] is there (id=71908086)
pcibios: BIOS version 2.10
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi0: Power Button (fixed)
ACPI timer looks BAD  min = 2, max = 5, width = 3
ACPI timer looks BAD  min = 2, max = 5, width = 3
ACPI timer looks BAD  min = 2, max = 5, width = 3
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 5, width = 3
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 6, width = 4
ACPI timer looks BAD  min = 2, max = 5, width = 3
ACPI timer looks BAD  min = 2, max = 5, width = 3
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
AcpiOsDerivePciId: bus 0 dev 0 func 0
AcpiOsDerivePciId: bus 0 dev 0 func 0
AcpiOsDerivePciId: bus 0 dev 7 func 0
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
        map[10]: type 3, range 32, base f8000000, size 26, enabled
found-> vendor=0x8086, dev=0x7190, revid=0x02
        bus=0, slot=0, func=0
        class=06-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0006, statreg=0x2210, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7191, revid=0x02
        bus=0, slot=1, func=0
        class=06-04-00, hdrtype=0x01, mfdev=0
        cmdreg=0x001f, statreg=0x0220, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x88 (34000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x7110, revid=0x02
        bus=0, slot=7, func=0
        class=06-01-00, hdrtype=0x00, mfdev=1
        cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[20]: type 4, range 32, base 0000ffa0, size  4, enabled
found-> vendor=0x8086, dev=0x7111, revid=0x01
        bus=0, slot=7, func=1
        class=01-01-80, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[20]: type 4, range 32, base 0000ef80, size  5, enabled
pcib0: matched entry for 0.7.INTD (source )
pcib0: device is hardwired to IRQ 19
found-> vendor=0x8086, dev=0x7112, revid=0x01
        bus=0, slot=7, func=2
        class=0c-03-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=d, irq=19
        map[90]: type 4, range 32, base 00000440, size  4, enabled
found-> vendor=0x8086, dev=0x7113, revid=0x02
        bus=0, slot=7, func=3
        class=06-80-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1011, dev=0x0024, revid=0x03
        bus=0, slot=16, func=0
        class=06-04-00, hdrtype=0x01, mfdev=0
        cmdreg=0x0107, statreg=0x0290, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns)
        map[10]: type 3, range 32, base fd0ff000, size 12, enabled
        map[14]: type 4, range 32, base 0000ef40, size  5, enabled
        map[18]: type 1, range 32, base fea00000, size 20, enabled
pcib0: matched entry for 0.17.INTA (source )
pcib0: device is hardwired to IRQ 19
found-> vendor=0x8086, dev=0x1229, revid=0x05
        bus=0, slot=17, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
        intpin=a, irq=19
        powerspec 1  supports D0 D1 D2 D3  current D0
        map[10]: type 4, range 32, base 0000e400, size  8, enabled
        map[14]: type 1, range 32, base febfe000, size 12, enabled
pcib0: matched entry for 0.18.INTA (source )
pcib0: device is hardwired to IRQ 16
found-> vendor=0x9004, dev=0x7895, revid=0x04
        bus=0, slot=18, func=0
        class=01-00-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
        intpin=a, irq=16
        powerspec 1  supports D0 D3  current D0
        map[10]: type 4, range 32, base 0000e800, size  8, enabled
        map[14]: type 1, range 32, base febff000, size 12, enabled
pcib0: matched entry for 0.18.INTB (source )
pcib0: device is hardwired to IRQ 16
found-> vendor=0x9004, dev=0x7895, revid=0x04
        bus=0, slot=18, func=1
        class=01-00-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
        intpin=b, irq=16
        powerspec 1  supports D0 D3  current D0
        map[10]: type 3, range 32, base fd0fe000, size 12, enabled
        map[14]: type 4, range 32, base 0000ef20, size  5, enabled
        map[18]: type 1, range 32, base fe800000, size 20, enabled
pcib0: matched entry for 0.20.INTA (source )
pcib0: device is hardwired to IRQ 17
found-> vendor=0x8086, dev=0x1229, revid=0x04
        bus=0, slot=20, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
        intpin=a, irq=17
        powerspec 1  supports D0 D1 D2 D3  current D0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xf8000000-0xfbffffff at d
evice 0.0 on pci0
agp0: allocating GATT for aperture of size 64M
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1:   secondary bus     1
pcib1:   subordinate bus   1
pcib1:   I/O decode        0xc000-0xcfff
pcib1:   memory decode     0xfd100000-0xfe1fffff
pcib1:   prefetched decode 0xf2e00000-0xf4efffff
pci1: <PCI bus> on pcib1
pci1: physical bus=1
        map[10]: type 3, range 32, base f3000000, size 24, enabled
        map[14]: type 1, range 32, base fe1fc000, size 14, enabled
        map[18]: type 1, range 32, base fd800000, size 23, enabled
pcib0: matched entry for 0.1.INTA (source )
pcib0: device is hardwired to IRQ 16
pcib1: slot 0 INTA is routed to irq 16
found-> vendor=0x102b, dev=0x051f, revid=0x00
        bus=1, slot=0, func=0
        class=03-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=16
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 UDMA33 controller> port 0xffa0-0xffaf at device 7.1 on pci
0
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0-slave:  stat=0x00 err=0x01 lsb=0x7f msb=0x7f
ata0: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=15 ostat1=15
ata1-master: stat=0x1e err=0x1e lsb=0x1e msb=0x1e
ata1-slave:  stat=0x0a err=0x0a lsb=0x0a msb=0x0a
ata1-master: stat=0x24 err=0x24 lsb=0x24 msb=0x24
ata1-slave:  stat=0x10 err=0x10 lsb=0x10 msb=0x10
ata1-master: stat=0x2a err=0x2a lsb=0x2a msb=0x2a
ata1-master: stat=0x15 err=0x15 lsb=0x15 msb=0x15
ata1-master: stat=0x01 err=0x01 lsb=0x01 msb=0x01
ata1: reset tp2 mask=03 stat0=01 stat1=10 devices=0x0
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0xef80-0xef9f irq 19 at de
vice 7.2 on pci0
usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pcib2: <PCI-PCI bridge> at device 16.0 on pci0
pcib2:   secondary bus     2
pcib2:   subordinate bus   2
pcib2:   I/O decode        0xd000-0xdfff
pcib2:   memory decode     0xfe200000-0xfe2fffff
pcib2:   prefetched decode 0xf4f00000-0xf4ffffff
pci2: <PCI bus> on pcib2
pci2: physical bus=2
fxp0: <Intel 82558 Pro/100 Ethernet> port 0xef40-0xef5f mem 0xfea00000-0xfeaffff
f,0xfd0ff000-0xfd0fffff irq 19 at device 17.0 on pci0
fxp0: using memory space register mapping
fxp0: Ethernet address 00:e0:81:10:09:c2
fxp0: PCI IDs: 8086 1229 8086 0008 0005
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp0: bpf attached
ahc0: <Adaptec aic7895 Ultra SCSI adapter> port 0xe400-0xe4ff mem 0xfebfe000-0xf
ebfefff irq 16 at device 18.0 on pci0
ahc0: Defaulting to MEMIO off
ahc0: Reading SEEPROM...done.
ahc0: internal 50 cable not present, internal 68 cable not present
ahc0: external cable not present
ahc0: BIOS eeprom is present
ahc0: High byte termination Enabled
ahc0: Low byte termination Enabled
ahc0: Downloading Sequencer Program... 412 instructions downloaded
ahc0: Features 0x16235, Bugs 0x15, Flags 0x20485540
aic7895C: Ultra Wide Channel A, SCSI Id=7, 32/253 SCBs
ahc1: <Adaptec aic7895 Ultra SCSI adapter> port 0xe800-0xe8ff mem 0xfebff000-0xf
ebfffff irq 16 at device 18.1 on pci0
ahc1: Defaulting to MEMIO off
ahc1: Reading SEEPROM...done.
ahc1: internal 50 cable not present, internal 68 cable not present
ahc1: external cable not present
ahc1: BIOS eeprom is present
ahc1: High byte termination Enabled
ahc1: Low byte termination Enabled
ahc1: Downloading Sequencer Program... 412 instructions downloaded
ahc1: Features 0x16235, Bugs 0x15, Flags 0x20485540
aic7895C: Ultra Wide Channel B, SCSI Id=7, 32/253 SCBs
fxp1: <Intel 82558 Pro/100 Ethernet> port 0xef20-0xef3f mem 0xfe800000-0xfe8ffff
f,0xfd0fe000-0xfd0fefff irq 17 at device 20.0 on pci0
fxp1: using memory space register mapping
fxp1: Ethernet address 00:a0:c9:b0:13:df
fxp1: PCI IDs: 8086 1229 8086 0009 0004
fxp1: Dynamic Standby mode is disabled
miibus1: <MII bus> on fxp1
inphy1: <i82555 10/100 media interface> on miibus1
inphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
fxp1: bpf attached
acpi_button0: <Sleep Button> on acpi0
unknown: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
psm0: unable to allocate IRQ
fdc0: output ready timeout
fdc0: cmd 3 failed at out byte 1 of 3
sio0: irq maps: 0x4201 0x4211 0x4201 0x4201
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A, console
sio1: irq maps: 0x4201 0x4209 0x4201 0x4201
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
fdc0: output ready timeout
fdc0: cmd 3 failed at out byte 1 of 3
unknown: not probed (disabled)
unknown: not probed (disabled)
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
Trying Read_Port at 203
CTL0043: start dependent (0)
CTL0043: adding irq mask 0x20
CTL0043: adding dma mask 0x2
CTL0043: adding dma mask 0x8
CTL0043: adding io range 0x220-0x22f, size=0x10, align=0x1
CTL0043: adding io range 0x330-0x331, size=0x2, align=0x1
CTL0043: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0043: start dependent (1)
CTL0043: adding irq mask 0x6a0
CTL0043: adding dma mask 0xb
CTL0043: adding dma mask 0xb
CTL0043: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0043: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0043: adding io range 0x388-0x38b, size=0x4, align=0x1
CTL0043: start dependent (1)
CTL0043: adding irq mask 0x6a0
CTL0043: adding dma mask 0xb
CTL0043: adding dma mask 0xb
CTL0043: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0043: adding io range 0x300-0x331, size=0x2, align=0x30
CTL0043: start dependent (1)
CTL0043: adding irq mask 0x6a0
CTL0043: adding dma mask 0xb
CTL0043: adding dma mask 0xb
CTL0043: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0043: start dependent (2)
CTL0043: adding irq mask 0x6a0
CTL0043: adding dma mask 0xb
CTL0043: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0043: adding io range 0x300-0x331, size=0x2, align=0x10
CTL0043: adding io range 0x388-0x397, size=0x4, align=0x4
CTL0043: start dependent (2)
CTL0043: adding irq mask 0x6a0
CTL0043: adding dma mask 0xb
CTL0043: adding io range 0x220-0x28f, size=0x10, align=0x20
CTL0043: end dependent
CTL7005: start dependent (0)
CTL7005: adding io range 0x201-0x201, size=0x1, align=0x1
CTL7005: start dependent (1)
CTL7005: adding io range 0x200-0x20f, size=0x1, align=0x1
CTL7005: end dependent
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xc8000-0xcc7ff,0xc0000-0xc7fff on isa0
pmtimer0 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f
0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
lnc0: not probed (disabled)
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
ppc0 failed to probe at irq 7 on isa0
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
kbdc: DIAGNOSE status:0055
kbdc: TEST_KBD_PORT status:0000
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x100>
sc0: fb0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 60 4f 50 83 55 81 
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
VGA parameters in BIOS for mode 24
50 18 10 00 10 00 03 00 02 67 60 4f 50 83 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
EGA/VGA parameters to be used for mode 24
50 18 10 00 10 00 03 00 02 67 60 4f 50 83 55 81 
bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff 
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <Audio> failed to probe at port 0x388-0x38b,0x330-0x331,0x220-0x22f irq
 5 drq 3,1 on isa0
unknown: <Game> failed to probe at port 0x201 on isa0
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 400911753 Hz quality -100
Timecounters tick every 10.000 msec
lo0: bpf attached

End of MIME message
Received on Mon Nov 24 2003 - 09:03:19 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:30 UTC