Hi Soren, please help. I can't boot kernel after ATAng. It founds one extra ATA device (I have no ata1-slave attached) and then panics. All details in PR kern/57156. In short: ad0: setting UDMA33 on Intel PIIX4 chip GEOM: create disk ad0 dp=0xc1d00970 ad0: <TOSHIBA MK4019GAX/FA002D> ATA-5 disk at ata0-master ad0: 38154MB (78140160 sectors), 77520 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, UDMA33 GEOM: new disk ad0 [0] f:00 typ:6 s(CHS):0/1/1 e(CHS):969/239/63 s:63 l:14666337 [1] f:00 typ:160 s(CHS):970/0/1 e(CHS):996/239/63 s:14666400 l:408240 [2] f:80 typ:165 s(CHS):997/0/1 e(CHS):1023/239/63 s:15074640 l:41942880 [3] f:00 typ:165 s(CHS):1023/0/1 e(CHS):1023/239/63 s:57017520 l:21122640 GEOM: Configure ad0s1, start 32256 length 7509164544 end 7509196799 GEOM: Configure ad0s2, start 7509196800 length 209018880 end 7718215679 GEOM: Configure ad0s3, start 7718215680 length 21474754560 end 9192970239 GEOM: Configure ad0s4, start 29192970240 length 10814791680 end 40007761919 GEOM: Configure ad0s3a, start 0 length 134217728 end 134217727 GEOM: Configure ad0s3b, start 134217728 length 268435456 end 402653183 GEOM: Configure ad0s3c, start 0 length 21474754560 end 21474754559 GEOM: Configure ad0s3e, start 402653184 length 6442450944 end 6845104127 GEOM: Configure ad0s3f, start 6845104128 length 14629650432 end 1474754559 GEOM: Configure ad0s4c, start 0 length 10814791680 end 10814791679 GEOM: Configure ad0s4e, start 0 length 134217728 end 134217727 GEOM: Configure ad0s4f, start 134217728 length 8915517440 end 9049735167 ata1-slave: pio=0x08 wdma=0xffffffff udma=0xffffffff cable=40pin ata1-master: pio=0x09 wdma=0xffffffff udma=0xffffffff cable=40pin ad1: FAILURE - SETFEATURES status=51<READY,DSC,ERROR> error=4<ABORTED> ad1: FAILURE - SETFEATURES status=51<READY,DSC,ERROR> error=4<ABORTED> ad1: FAILURE - SETFEATURES status=51<READY,DSC,ERROR> error=4<ABORTED> ad1: FAILURE setting PIO1 on Intel PIIX4 chip GEOM: create disk ad1 dp=0xc1d4b770 ad1: <MEMORYSTICK 4M 8K/SONY1.00> ATA-0 disk at ata1-master ad1: 3MB (7904 sectors), 247 C, 2 H, 16 S, 512 B ad1: 1 secs/int, 1 depth queue, BIOSPIO GEOM: new disk ad1 ad2: WARNING - SETFEATURES recovered from missing interrupt [0] f:80 typ:1 s(CHS):0/1/12 e(CHS):245/1/16 s:27 l:7845 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad1s1, start 13824 length 4016640 end 4030463 ad2: WARNING - SETFEATURES recovered from missing interrupt ad2: WARNING - SETFEATURES recovered from missing interrupt ad2: setting PIO0 on Intel PIIX4 chip GEOM: create disk ad2 dp=0xc1d4b970 ad2: </> ATA-0 disk at ata1-slave Fatal trap 18: integer divide fault while in kernel mode instruction pointer = 0x8:0xc03fa088 stack pointer = 0x10:0xc05c5c54 frame pointer = 0x10:0xc05c5cd0 code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = 0 (swapper) kernel: type 18 trap, code=0 Stopped at __qdivrem+0x38: divl %ecx,%eax db> tra __qdivrem(0,0,0,0,0) at __qdivrem+0x38 __udivdi3(0,0,0,0,0) at __udivdi3+0x2e ad_attach(c1c712d4,1,c0ac6c50,c0445310,c05c5d74) at ad_attach+0x4aa ata_boot_attach(0,c02392d6,c046392c,0,c0445310) at ata_boot_attach+0x6f run_interrupt_driven_config_hooks(0,0,c0ac46f8,c0ac46f8,5c2c00) at run_interrupt_driven_config_hooks+0x2b mi_startup() at mi_startup+0xa1 begin() at begin+0x2c db> Any solution or workaround ? -- Vladimir B. Grebenschikov <vova_at_sw.ru> SWsoft Inc.Received on Mon Oct 06 2003 - 09:47:44 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:24 UTC