Hi, some severe problems with a brand new DELL Latitude D600 laptop. It has a Broadcom BCM5702 Gigabit Ethernet, ASIC rev. 0x1002, on board. On the 1st boot FreeBSD 5.1-current from a self made CD-ROM (-current from yesterday) paniced during 1st boot from CD (just before installation). It had a Fritz PCMCIA card inserted. The next installation attempt from CD was, trying to boot without ACPI, which succeeded. Then after installation and reboot it turns out that I can boot without panic even with ACPI enabled. But it might be due to one change, I replaced the Fritz ISDN card with a 3COM 3CCFE575BT, since the broadcom bge0 interface doesn't run properly. In short, these are the problems: 1. bge0 driver doesn't find PHY Laptop is connected with a working shielded CAT 5 cable to a DLINK DI 804 DSL router who has a builtin 10/100 4-port switch supporting full and half duplex cabability. 2. pcmcia card is not recognized. 3COM 3CCFE575BT This card runs fine in -current on a Toshiba Satellite PRO 4360. You see pccardd -d output at the end of the log. 3. Panic with ACPI enabled and Fritz ISDN card inserted AVM Fritz!Card PCMCIA v2.0 (info on the label) I booted now with serial com console and with boot_verbose set At the end you see - "uname -a" command- and - "pccardd -d" output Any chance to get that fixed ? Or do you think I'll better using FreeBSD 4.9 with that hardware ? Has 4.9 broadcom support ? boot -\|/-\|/-\|/-\|/-\|/-\|/-/boot/kernel/acpi.ko text=0x3b3dc \|/-\|/-\|/-\|/data=0x168c+0xee0 -syms=[0x4+0x5b30\+0x4+0x78b8|/] -\|/-\|SMAP type=01 base=0000000000000000 len=000000000009f000 SMAP type=02 base=000000000009f000 len=0000000000001000 SMAP type=01 base=0000000000100000 len=000000001feae000 SMAP type=02 base=000000001ffae000 len=0000000000052000 SMAP type=02 base=00000000feda0000 len=0000000000060000 SMAP type=02 base=00000000ffb00000 len=0000000000500000 Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.1-20031024-SNAP #0: Sat Oct 25 03:04:22 GMT 2003 root_at_titan.klemm.apsfilter.org:/usr/obj/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a61000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a611cc. Calibrating clock(s) ... i8254 clock: 1193119 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 1395477939 Hz CPU: Intel(R) Pentium(R) M processor 1400MHz (1395.48-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x695 Stepping = 5 Features=0xa7e9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,TM,PBE> real memory = 536535040 (511 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c26000 - 0x000000001f688fff, 514207744 bytes (125539 pages) avail memory = 511598592 (487 MB) bios32: Found BIOS32 Service Directory header at 0xc00ffe80 bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0xc97e pnpbios: Found PnP BIOS data at 0xc00fe2d0 pnpbios: Entry = f0000:e2f4 Rev = 1.0 pnpbios: Event flag at 4b4 Other BIOS signatures found: wlan: <802.11 Link Layer> null: <null device, zero device> random: <entropy source> mem: <memory & I/O> Pentium Pro MTRR support enabled npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <DELL CPi R > on motherboard pci_open(1): mode 1 addr port (0x0cf8) is 0x80010014 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=33408086) pcibios: BIOS version 2.10 Using $PIR table, 9 entries at 0xc00fc590 PCI-Only Interrupts: none Location Bus Device Pin Link IRQs embedded 0 29 A 0x60 3 4 5 6 7 9 10 11 12 14 15 embedded 0 29 B 0x63 3 4 5 6 7 9 10 11 12 14 15 embedded 0 29 C 0x62 3 4 5 6 7 9 10 11 12 14 15 embedded 0 29 D 0x6b 3 4 5 6 7 9 10 11 12 14 15 embedded 0 30 A 0x60 3 4 5 6 7 9 10 11 12 14 15 embedded 0 30 B 0x61 3 4 5 6 7 9 10 11 12 14 15 embedded 0 30 C 0x62 3 4 5 6 7 9 10 11 12 14 15 embedded 0 30 D 0x63 3 4 5 6 7 9 10 11 12 14 15 embedded 0 31 A 0x62 3 4 5 6 7 9 10 11 12 14 15 embedded 0 31 B 0x61 3 4 5 6 7 9 10 11 12 14 15 embedded 1 0 A 0x60 3 4 5 6 7 9 10 11 12 14 15 embedded 2 0 A 0x62 3 4 5 6 7 9 10 11 12 14 15 embedded 2 1 A 0x63 3 4 5 6 7 9 10 11 12 14 15 embedded 2 1 B 0x63 none embedded 2 3 A 0x61 3 4 5 6 7 9 10 11 12 14 15 embedded 2 3 B 0x63 3 4 5 6 7 9 10 11 12 14 15 embedded 8 0 A 0x61 3 4 5 6 7 9 10 11 12 14 15 embedded 8 0 B 0x63 3 4 5 6 7 9 10 11 12 14 15 embedded 8 1 A 0x61 3 4 5 6 7 9 10 11 12 14 15 embedded 8 1 B 0x63 3 4 5 6 7 9 10 11 12 14 15 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 31 func 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 acpi_cpu0: <CPU> on acpi0 acpi_tz0: <Thermal Zone> on acpi0 acpi_acad0: <AC Adapter> on acpi0 acpi_cmbat0: <Control Method Battery> on acpi0 acpi_cmbat1: <Control Method Battery> on acpi0 acpi_lid0: <Control Method Lid Switch> on acpi0 acpi_button0: <Power Button> on acpi0 acpi_button1: <Sleep Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 ---- initial configuration ------------------------ \_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.31.0 \_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 0.31.1 \_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 0.31.2 \_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 0.31.3 \_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.29.0 \_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 0.29.1 \_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 0.29.2 \_SB_.PCI0.LNKH irq 11: [ 3 4 5 6 7 9 10 11 12 14 15] low,level,sharable 0.29.3 \_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.1.0 \_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 0.1.1 ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- \_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.31.0 \_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 0.31.1 \_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 0.31.2 \_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 0.31.3 \_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.29.0 \_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 0.29.1 \_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 0.29.2 \_SB_.PCI0.LNKH irq 11: [ 3 4 5 6 7 9 10 11 12 14 15] low,level,sharable 0.29.3 \_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 0.1.0 \_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 0.1.1 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base e0000000, size 27, enabled found-> vendor=0x8086, dev=0x3340, revid=0x03 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x3341, revid=0x03 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000bf80, size 5, enabled pcib0: matched entry for 0.29.INTA (source \_SB_.PCI0.LNKA) pcib0: slot 29 INTA is routed to irq 11 found-> vendor=0x8086, dev=0x24c2, revid=0x01 bus=0, slot=29, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 map[20]: type 4, range 32, base 0000bf40, size 5, enabled pcib0: matched entry for 0.29.INTB (source \_SB_.PCI0.LNKD) pcib0: slot 29 INTB is routed to irq 11 found-> vendor=0x8086, dev=0x24c4, revid=0x01 bus=0, slot=29, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 map[20]: type 4, range 32, base 0000bf20, size 5, enabled pcib0: matched entry for 0.29.INTC (source \_SB_.PCI0.LNKC) pcib0: slot 29 INTC is routed to irq 11 found-> vendor=0x8086, dev=0x24c7, revid=0x01 bus=0, slot=29, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=11 map[10]: type 1, range 32, base f4fffc00, size 10, enabled pcib0: matched entry for 0.29.INTD (source \_SB_.PCI0.LNKH) pcib0: slot 29 INTD is routed to irq 11 found-> vendor=0x8086, dev=0x24cd, revid=0x01 bus=0, slot=29, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=11 powerspec 2 supports D0 D3 current D0 found-> vendor=0x8086, dev=0x2448, revid=0x81 bus=0, slot=30, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x8080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x24cc, revid=0x01 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 4, range 32, base 000001f0, size 3, enabled map[14]: type 4, range 32, base 000003f4, size 2, enabled map[18]: type 4, range 32, base 00000170, size 3, enabled map[1c]: type 4, range 32, base 00000374, size 2, enabled map[20]: type 4, range 32, base 0000bfa0, size 4, enabled found-> vendor=0x8086, dev=0x24ca, revid=0x01 bus=0, slot=31, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 map[10]: type 4, range 32, base 0000b800, size 8, enabled map[14]: type 4, range 32, base 0000bc40, size 6, enabled map[18]: type 1, range 32, base f4fff800, size 9, enabled map[1c]: type 1, range 32, base f4fff400, size 8, enabled pcib0: matched entry for 0.31.INTB (source \_SB_.PCI0.LNKB) pcib0: slot 31 INTB is routed to irq 11 found-> vendor=0x8086, dev=0x24c5, revid=0x01 bus=0, slot=31, func=5 class=04-01-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 powerspec 2 supports D0 D3 current D0 map[10]: type 4, range 32, base 0000b400, size 8, enabled map[14]: type 4, range 32, base 0000b080, size 7, enabled pcib0: matched entry for 0.31.INTB (source \_SB_.PCI0.LNKB) pcib0: slot 31 INTB is routed to irq 11 found-> vendor=0x8086, dev=0x24c6, revid=0x01 bus=0, slot=31, func=6 class=07-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 powerspec 2 supports D0 D3 current D0 agp0: <Intel 82855 host to AGP bridge> mem 0xe0000000-0xe7ffffff at device 0.0 on pci0 agp0: allocating GATT for aperture of size 128M pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xc000-0xcfff pcib1: memory decode 0xfc000000-0xfdffffff pcib1: prefetched decode 0xe8000000-0xefffffff ---- initial configuration ------------------------ \_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 1.0.0 ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- \_SB_.PCI0.LNKA irq 11: [ 9 10 11] low,level,sharable 1.0.0 pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 map[10]: type 3, range 32, base e8000000, size 27, enabled map[14]: type 4, range 32, base 0000c000, size 8, enabled map[18]: type 1, range 32, base fcff0000, size 16, enabled pcib1: matched entry for 1.0.INTA (source \_SB_.PCI0.LNKA) pcib1: slot 0 INTA is routed to irq 11 found-> vendor=0x1002, dev=0x4c66, revid=0x01 bus=1, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x01a7, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 pci1: <display, VGA> at device 0.0 (no driver attached) uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f irq 11 at device 29.0 on pci0 usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered ugen0: vendor 0x413c product 0x8000, rev 1.10/5.65, addr 2 uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f irq 11 at device 29.1 on pci0 usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f irq 11 at device 29.2 on pci0 usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered pci0: <serial bus, USB> at device 29.7 (no driver attached) pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0xd000-0xefff pcib2: memory decode 0xf6000000-0xfbffffff pcib2: prefetched decode 0xfff00000-0xfffff ---- initial configuration ------------------------ \_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 2.1.0 \_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 2.1.1 \_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 2.3.0 \_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 2.3.1 \_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 2.0.0 \_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 2.8.0 \_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 2.8.1 ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- \_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 2.1.0 \_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 2.1.1 \_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 2.3.0 \_SB_.PCI0.LNKD irq 11: [ 5 7 9 10 11] low,level,sharable 2.3.1 \_SB_.PCI0.LNKC irq 11: [ 9 10 11] low,level,sharable 2.0.0 \_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 2.8.0 \_SB_.PCI0.LNKB irq 11: [ 5 7] low,level,sharable 2.8.1 pci2: <ACPI PCI bus> on pcib2 pci2: physical bus=2 map[10]: type 1, range 64, base faff0000, size 16, enabled pcib2: matched entry for 2.0.INTA (source \_SB_.PCI0.LNKC) pcib2: slot 0 INTA is routed to irq 11 found-> vendor=0x14e4, dev=0x16a6, revid=0x02 bus=2, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0116, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 8 messages, 64 bit found-> vendor=0x1217, dev=0x7113, revid=0x20 bus=2, slot=1, func=0 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0000, statreg=0x0410, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D1 D2 D3 current D0 found-> vendor=0x1217, dev=0x7113, revid=0x20 bus=2, slot=1, func=1 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0000, statreg=0x0410, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base fafee000, size 13, enabled pcib2: matched entry for 2.3.INTA (source \_SB_.PCI0.LNKB) pcib2: slot 3 INTA is routed to irq 11 found-> vendor=0x14e4, dev=0x4320, revid=0x02 bus=2, slot=3, func=0 class=02-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 bge0: <Broadcom BCM5702 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xfaff0000-0xfaffffff irq 11 at device 0.0 on pci2 pcib2: device bge0 requested decoded memory range 0xfaff0000-0xfaffffff bge0: Ethernet address: 00:0b:db:df:53:b1 miibus0: <MII bus> on bge0 brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge0: bpf attached cbb0: <PCI-CardBus Bridge> at device 1.0 on pci2 pcib2: device cbb0 requested decoded memory range 0xf6000000-0xfbffffff cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 pcib2: matched entry for 2.1.INTA (source \_SB_.PCI0.LNKD) pcib2: slot 1 INTA is routed to irq 11 cbb0: [MPSAFE] cbb0: PCI Configuration space: 0x00: 0x71131217 0x04100007 0x06070020 0x00822000 0x10: 0xf6000000 0x020000a0 0x20000000 0xfffff000 0x20: 0x00000000 0xfffff000 0x00000000 0x0000fffd 0x30: 0x00000001 0x0000fffd 0x00000001 0x0440010b 0x40: 0x011d1028 0x00000001 0x00000000 0x00000000 0x50: 0x00000000 0x00000000 0x00000000 0x00000000 0x60: 0x00000000 0x00000000 0x00000000 0x00000000 0x70: 0x00000000 0x00000000 0x00000000 0x00000000 0x80: 0x00000000 0x00000000 0x00000000 0x018c1882 0x90: 0x00350003 0x00000000 0x00000000 0x00000000 0xa0: 0xfe020001 0x00c04000 0x00000000 0x0000000d 0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 0xd0: 0x08004000 0x80820bea 0x00000000 0x00400000 0xe0: 0x00828000 0x00000000 0x00000000 0x00000000 0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 cbb1: <PCI-CardBus Bridge> at device 1.1 on pci2 pcib2: device cbb1 requested decoded memory range 0xf6000000-0xfbffffff cardbus1: <CardBus bus> on cbb1 pccard1: <16-bit PCCard bus> on cbb1 pcib2: matched entry for 2.1.INTA (source \_SB_.PCI0.LNKD) pcib2: slot 1 INTA is routed to irq 11 cbb1: [MPSAFE] cbb1: PCI Configuration space: 0x00: 0x71131217 0x04100007 0x06070020 0x00822000 0x10: 0xf6001000 0x020000a0 0x20000000 0xfffff000 0x20: 0x00000000 0xfffff000 0x00000000 0x0000fffd 0x30: 0x00000001 0x0000fffd 0x00000001 0x0440010b 0x40: 0x011d1028 0x00000001 0x00000000 0x00000000 0x50: 0x00000000 0x00000000 0x00000000 0x00000000 0x60: 0x00000000 0x00000000 0x00000000 0x00000000 0x70: 0x00000000 0x00000000 0x00000000 0x00000000 0x80: 0x00000000 0x00000000 0x00000000 0x018c1882 0x90: 0x00350003 0x00000000 0x00000000 0x00000000 0xa0: 0xfe020001 0x00c04000 0x00000000 0x0000000d 0xb0: 0x00000000 0x00000000 0x00000000 0x00000000 0xc0: 0x00000000 0x00000000 0x00000000 0x00000000 0xd0: 0x08004000 0x80800bea 0x00000000 0x04400000 0xe0: 0x00828000 0x00000000 0x00000000 0x00000000 0xf0: 0x00000000 0x00000000 0x00000000 0x00000000 pci2: <network> at device 3.0 (no driver attached) isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH4 UDMA100 controller> port 0xbfa0-0xbfaf,0x374-0x377,0x170-0x177,0x3f4-0x3f7,0x1f0-0x1f7 at device 31.1 on pci0 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: reset tp1 mask=03 ostat0=50 ostat1=00 ata1-master: stat=0x10 err=0x01 lsb=0x14 msb=0xeb ata1-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata1: reset tp2 mask=03 stat0=10 stat1=00 devices=0x4<ATAPI_MASTER> ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] pci0: <multimedia, audio> at device 31.5 (no driver attached) pci0: <simple comms> at device 31.6 (no driver attached) psmcpnp0 irq 12 on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x1d0000 psm0: current command byte:0065 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fa kbdc: RESET_AUX status:00aa kbdc: RESET_AUX ID:0000 kbdc: RESET_AUX return code:00fa kbdc: RESET_AUX status:00aa kbdc: RESET_AUX ID:0000 psm: status 00 02 64 psm: status 00 00 64 psm: status 00 03 64 psm: status 00 03 64 psm: data 08 00 00 psm: status 22 02 14 psm: data 08 00 00 psm: status 00 02 64 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model GlidePoint, device ID 0-00, 2 buttons psm0: config:00000000, flags:00000000, packet size:3 psm0: syncmask:c0, syncbits:00 unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 ex_isa_identify() sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fdc0: ready for input in output fdc0: cmd 3 failed at out byte 1 of 3 fdc0 failed to probe at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0 fe0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) ppc0: parallel port found at 0x378 ppc0: using extended I/O port range ppc0: ECP SPP ECP+EPP SPP ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lp0: bpf attached lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x100> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio0: irq maps: 0x1 0x11 0x1 0x1 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A, console sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0x1 0x1 0x1 0x1 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k vga0: vga: WARNING: video mode switching is not fully supported on this adapter VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 69 4f 4f 8d 55 83 9e 1f 00 4f 0d 0e 00 00 07 80 8f 82 8f 28 1f 8f 9f a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 00 00 03 00 02 67 69 4f 4f 8d 55 83 9e 1f 00 4f 0d 0e 00 00 07 80 8f 82 8f 28 1f 8f 9f a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered Timecounter "TSC" frequency 1395477939 Hz quality 800 Timecounters tick every 10.000 msec lo0: bpf attached malloc() of "16" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/net/if.c:459 malloc() of "256" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/net/if.c:459 malloc() of "512" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/net/if.c:459 malloc() of "64" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/net/if.c:459 malloc() of "64" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/netinet6/in6.c:2295 malloc() of "16" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/netinet6/in6.c:2295 malloc() of "256" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/netinet6/in6.c:2295 malloc() of "512" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/netinet6/in6.c:2295 malloc() of "64" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/netinet6/in6.c:2295 malloc() of "64" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/netinet6/in6.c:2295 malloc() of "16" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/netinet6/in6.c:2295 malloc() of "256" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/netinet6/in6.c:2295 malloc() of "512" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/netinet6/in6.c:2295 malloc() of "64" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/netinet6/in6.c:2295 malloc() of "64" with the following non-sleepable locks held: exclusive sleep mutex ifnet r = 0 (0xc0924e20) locked _at_ /usr/src/sys/netinet6/in6.c:2295 ata1: spurious interrupt - status=0x00 error=0x01 acpi_cpu0: set speed to 100.0% acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% acpi_acad0: acline initialization start acpi_acad0: On Line acpi_acad0: acline initialization done, tried 1 times acpi_cmbat0: battery initialization start acpi_cmbat1: battery initialization start cardbus0: Resource not specified in CIS: id=10, size=10000 pcib2: device cardbus0 requested decoded memory range 0xf6000000-0xfbffffff found-> vendor=0x14e4, dev=0x16a6, revid=0x02 bus=2, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0xa8 (5040 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns) intpin=a, irq=222 powerspec 2 supports D0 D3 current D0 MSI supports 8 messages, 64 bit cardbus0: <network, ethernet> at device 0.0 (no driver attached) cbb0: CardBus card activation failed pcib2: device pccard1 requested decoded memory range 0xf6000000-0xfbffffff pccard1: CIS version PC Card Standard 7.0 pccard1: CIS info: O2Micro, SmartCardBus Reader, V1.0 pccard1: Manufacturer code 0xffff, product 0x1 pccard1: function 0: unspecified, ccr addr 220 mask 1 pccard1: function 0, config table entry 1: I/O card; irq mask beb8; iomask 5, iospace 0-1f; memspace 0-ff; io16 irqlevel pcib2: device pccard1 requested decoded I/O range 0x100-0xffffffff pcib2: device pccard1 requested decoded memory range 0xf6000000-0xfbffffff pccard1: <unknown card> (manufacturer=0xffff, product=0x0001) at function 0 pccard1: CIS info: O2Micro, SmartCardBus Reader, V1.0 ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ad0: setting UDMA100 on Intel ICH4 chip GEOM: create disk ad0 dp=0xc4852d70 ad0: <IC25N040ATCS05-0/CS4OA63A> ATA-5 disk at ata0-master ad0: 38154MB (78140160 sectors), 77520 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, UDMA100 GEOM: new disk ad0 ar: FreeBSD check1 failed [0] f:00 typ:222 s(CHS):0/1/1 e(CHS):5/254/63 s:63 l:96327 [1] f:00 typ:7 s(CHS):6/0/1 e(CHS):1023/254/63 s:96390 l:20482875 [2] f:00 typ:15 s(CHS):1023/255/63 e(CHS):1023/254/63 s:20579265 l:20482875 [3] f:80 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:41062140 l:20964825 GEOM: Configure ad0s1, start 32256 length 49319424 end 49351679 GEOM: Configure ad0s2, start 49351680 length 10487232000 end 10536583679 GEOM: Configure ad0s3, start 10536583680 length 10487232000 end 21023815679 GEOM: Configure ad0s4, start 21023815680 length 10733990400 end 31757806079 ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin acd0: setting PIO4 on Intel ICH4 chip acd0: <QSI CD-RW/DVD-ROM SBW-242/UD22> CDRW drive at ata1 as master acd0: read 4126KB/s (4126KB/s) write 4126KB/s (4126KB/s), 2048KB buffer, PIO4 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet acd0: Writes: CDR, CDRW, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: CD-R 120mm data disc MBREXT Slice 5 on ad0s3: [0] f:00 typ:11 s(CHS):1023/1/1 e(CHS):1023/254/63 s:63 l:2040192 [1] f:00 typ:5 s(CHS):1023/0/1 e(CHS):1023/254/63 s:2040255 l:18442620 GEOM: Configure ad0s5, start 32256 length 1044578304 end 1044610559 MBREXT Slice 6 on ad0s3: [0] f:00 typ:11 s(CHS):1023/1/1 e(CHS):1023/254/63 s:63 l:18442557 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad0s6, start 1044642816 length 9442589184 end 10487231999 GEOM: Configure ad0s4a, start 0 length 536870912 end 536870911 GEOM: Configure ad0s4b, start 536870912 length 1073741824 end 1610612735 GEOM: Configure ad0s4c, start 0 length 10733990400 end 10733990399 GEOM: Configure ad0s4d, start 1610612736 length 1073741824 end 2684354559 GEOM: Configure ad0s4e, start 2684354560 length 8049635840 end 10733990399 Mounting root from ufs:/dev/ad0s4a start_init: trying /sbin/init Loading configuration files. Entropy harvesting: interrupts ethernet point_to_point. swapon: adding /dev/ad0s4b as swap device Starting file system checks: /dev/ad0s4a: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ad0s4a: clean, 208221 free (1141 frags, 25885 blocks, 0.4% fragmentation) /dev/ad0s4e: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ad0s4e: clean, 3578286 free (2174 frags, 447014 blocks, 0.1% fragmentation) /dev/ad0s4d: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ad0s4d: clean, 506413 free (21 frags, 63299 blocks, 0.0% fragmentation) Setting hostname: aklemm.klemm.apsfilter.org. lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3 Starting dhclient. bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: RX CPU self-diagnostics failed! bge0: flow-through queue init failed bge0: initialization failure bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: RX CPU self-diagnostics failed! bge0: flow-through queue init failed bge0: initialization failure -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: RX CPU self-diagnostics failed! bge0: flow-through queue init failed bge0: initialization failure bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: flags=8803<UP,BROADCAST,SIMPLEX,MULTICAST> mtu 1500 options=1b<RXCSbUM,TXCSUM,VLAN_MgTU,VLAN_HWTAGGINeG> 0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out inet6 fe80::20b:dbff:fedf:53b1%bge0 prefixlen 64 scopeid 0x1 inet 0.0.0.0 nebtmask 0xff000000g broadcast 255.2e55.255.255 eth0er 00:0b:db:df:5:3:b1 PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out media: Ethernet autoselect status: no carrier Additional routing options:. hw.bus.devctl_disable: 0 -> 1 Mounting NFS file systems:. Starting syslogd. Oct 25 13:52:29 aklemm syslogd: kernel boot file is /boot/kernel/kernel ELF ldconfig path: /lib /usr/lib /usr/lib/compat a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout Starting usbd. Starting local daemons:. Updating motd. Configuring syscons: keymap keyrate font8x16 font8x14 font8x8 blanktime screensaver. Starting sshd. -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes Initial i386 initialization:. Additional ABI support:. Starting cron. Local package initialization:. Additional TCP options:. Starting moused:. Starting background file system checks in 60 seconds. Sat Oct 25 13:52:33 CEST 2003 bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes -0166: *** Error: UtAllocate: Attempt to allocate zero bytes bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out acpi_cmbat0: battery initialization failed, giving up acpi_cmbat1: battery initialization failed, giving up bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out V&Y read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out FreeBSD/i386 (aklemm.klemm.apsfilter.org) (ttyd0) login: rbge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out oot Password: Oct 25 13:53:47 aklemm login: ROOT LOGIN (root) ON ttyd0 Last login: Sat Oct 25 13:53:12 on ttyv0 Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.1-20031024-SNAP (GENERIC) #0: Sat Oct 25 03:04:22 GMT 2003 Welcome to FreeBSD! Before seeking technical support, please use the following resources: o Security advisories and updated errata information for all releases are at http://www.FreeBSD.org/releases/ - always consult the ERRATA section for your release first as it's updated frequently. o The Handbook and FAQ documents are at http://www.FreeBSD.org/ and, along with the mailing lists, can be searched by going to http://www.FreeBSD.org/search/. If the doc distribution has been installed, they're also available formatted in /usr/share/doc. If you still have a question or problem, please take the output of `uname -a', along with any relevant error messages, and email it as a question to the questions_at_FreeBSD.org mailing list. If you are unfamiliar with FreeBSD's directory layout, please refer to the hier(7) manual page. If you are not familiar with manual pages, type `man man'. You may also use sysinstall(8) to re-enter the installation and configuration utility. Edit /etc/motd to change this login announcement. aklemm# bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out ps -ax PID TT STAT TIME COMMAND 0 ?? DLs 0:00.00 (swapper) 1 ?? SLs 0:00.11 /sbin/init -- 2 ?? DL 0:00.87 (g_event) 3 ?? DL 0:00.05 (g_up) 4 ?? DL 0:00.09 (g_down) 5 ?? DL 0:00.00 (taskqueue) 6 ?? IL 0:00.00 (acpi_task0) 7 ?? IL 0:02.18 (acpi_task1) 8 ?? IL 0:00.06 (acpi_task2) 9 ?? DL 0:00.00 (cbb0) 10 ?? DL 0:00.00 (ktrace) 11 ?? RL 1:26.64 (idle) 12 ?? WL 0:00.01 (swi1: net) 13 ?? WL 0:00.08 (swi8: tty:sio clock) 15 ?? DL 0:00.01 (random) 17 ?? WL 0:00.00 (swi7: acpitaskq) 21 ?? WL 0:00.03 (swi7: task queue) 23 ?? WL 0:00.00 (irq9: acpi0) 24 ?? DL 0:00.02 (acpi_thermal) 25 ?? WL 0:00.00 (irq11: cbb0 cbb1++*) 26 ?? DL 0:00.00 (usb0) 27 ?? DL 0:00.00 (usbtask) 28 ?? DL 0:00.00 (usb1) 29 ?? DL 0:00.00 (usb2) 30 ?? DL 0:00.00 (cbb1) 31 ?? WL 0:00.02 (irq14: ata0) 32 ?? WL 0:00.00 (irq15: ata1) 33 ?? WL 0:00.01 (irq1: atkbd0) 35 ?? WL 0:00.00 (irq7: ppc0) 36 ?? WL 0:00.00 (swi0: tty:sio) 40 ?? DL 0:00.00 (pagedaemon) 41 ?? DL 0:00.00 (vmdaemon) 42 ?? DL 0:00.46 (pagezero) 43 ?? DL 0:00.00 (bufdaemon) 44 ?? DL 0:00.00 (vnlru) 45 ?? DL 0:00.01 (syncer) 46 ?? IL 0:00.00 (nfsiod 0) 47 ?? IL 0:00.00 (nfsiod 1) 48 ?? IL 0:00.00 (nfsiod 2) 49 ?? IL 0:00.00 (nfsiod 3) 146 ?? Is 0:00.00 adjkerntz -i 185 ?? Ss 0:05.18 /sbin/dhclient bge0 241 ?? Ss 0:00.09 /usr/sbin/syslogd -s 337 ?? Ss 0:00.00 /usr/sbin/usbd 395 ?? Is 0:00.08 /usr/sbin/sshd 401 ?? Ss 0:00.01 sendmail: accepting connections (sendmail) 404 ?? Is 0:00.00 sendmail: Queue runner_at_00:30:00 for /var/spool/client 418 ?? Is 0:00.01 /usr/sbin/cron 442 ?? Is 0:00.00 /usr/sbin/moused -p /dev/psm0 -t auto 470 v0 Is 0:00.12 login [pam] (login) 478 v0 S+ 0:00.03 -csh (csh) 471 v1 Is+ 0:00.01 /usr/libexec/getty Pc ttyv1 472 v2 Is+ 0:00.01 /usr/libexec/getty Pc ttyv2 473 v3 Is+ 0:00.01 /usr/libexec/getty Pc ttyv3 474 v4 Is+ 0:00.01 /usr/libexec/getty Pc ttyv4 475 v5 Is+ 0:00.01 /usr/libexec/getty Pc ttyv5 476 v6 Is+ 0:00.01 /usr/libexec/getty Pc ttyv6 477 v7 Is+ 0:00.01 /usr/libexec/getty Pc ttyv7 484 d0 Ss 0:00.12 login [pam] (login) 485 d0 S 0:00.03 -csh (csh) 487 d0 R+ 0:00.00 ps -ax aklemm# bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out unam e e -bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out a FreeBSD aklemm.klemm.apsfilter.org 5.1-20031024-SNAP FreeBSD 5.1-20031024-SNAP #0: Sat Oct 25 03:04:22 GMT 2003 root_at_titan.klemm.apsfilter.org:/usr/obj/usr/src/sys/GENERIC i386 aklemm# aklemm# uname -a FreeBSD aklemm.klemm.apsfilter.org 5.1-20031024-SNAP FreeBSD 5.1-20031024-SNAP #0: Sat Oct 25 03:04:22 GMT 2003 root_at_titan.klemm.apsfilter.org:/usr/obj/usr/src/sys/GENERIC i386 aklemm# bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out aklemm# pbge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out ccardd -dbge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out aklemm# Oct 25 13:54:25 aklemm pccardd[490]: fatal error: no PC-CARD slots aklemm# bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out aklemm# aklemm# pccardd -d aklemm# Oct 25 13:54:32 aklemm pccardd[491]: fatal error: no PC-CARD slots aklemm# aklemm# aklemm# bge0: PHY read timed out bge0: PHY read timed out bge0: PHY read timed out aklemm# Andreas /// -- Andreas Klemm - Powered by FreeBSD 5.1-CURRENT Need a magic printfilter today ? -> http://www.apsfilter.org/Received on Sat Oct 25 2003 - 03:15:23 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:26 UTC