Good Morning, I've had this problem for a while now, however due to educational constraints I've been unable to look at it for a while. I have several gigabit lan cards on a gig switch, these cards have a Broadcom chipset and are sold by Netgear as GA302T (if I recall correctly). The card works perfectly under Windows. After sending a small ammount of data through them they simply stop responding to the network. A couple of seconds later they report to the console "bge0: watchdog timeout -- resetting", only way to get it to talk again is to reboot. These cards worked under 4.7 a while back, but I'd imagin it's more to do with interrupt and other things then that. The motherboard is a Tyan Tiger MPX. The motherboard nor network cards arn't exactly great by themselves, so I'm suprised I've not had more issues. For example, I can't use the last PCI slot on the board under 5.2 as it just seems to fail completely. If anyone could help me track this problem down and to solve it, I'd greatly apreciate it. Attached are a dmesg after "boot -v" and pciconf. Kind regards and thanks in advance, Peter. [xenon:~]$ dmesg L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L2 internal cache: 256 kbytes, 64 bytes/line, 1 lines/tag, 8-way associative real memory = 2146959360 (2047 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009cfff, 638976 bytes (156 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c29000 - 0x000000007dac9fff, 2095714304 bytes (511649 pages) 0x000000007ff00000 - 0x000000007ff77fff, 491520 bytes (120 pages) avail memory = 2095464448 (1998 MB) Table 'FACP' at 0x7fefef2e Table 'APIC' at 0x7fefefa2 MADT: Found table at 0x7fefefa2 MP Configuration Table version 1.4 found at 0xc009fd70 APIC: Using the MADT enumerator. MADT: Found CPU APIC ID 1 ACPI ID 0: enabled SMP: Added CPU 1 (AP) MADT: Found CPU APIC ID 0 ACPI ID 1: enabled SMP: Added CPU 0 (AP) ACPI APIC Table: <PTLTD APIC > APIC ID: physical 0, logical 0:0 APIC ID: physical 1, logical 0:1 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 1 cpu1 (AP): APIC ID: 0 bios32: Found BIOS32 Service Directory header at 0xc00f70d0 bios32: Entry = 0xfd6b0 (c00fd6b0) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xfd6b0+0x120 pnpbios: Found PnP BIOS data at 0xc00f7130 pnpbios: Entry = f0000:9aad Rev = 1.0 Other BIOS signatures found: APIC: CPU 0 has ACPI ID 0 APIC: CPU 1 has ACPI ID 1 MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000 ioapic0: intpin 0 -> ExtINT (edge, activehi) ioapic0: intpin 1 -> irq 1 (edge, activehi) ioapic0: intpin 2 -> irq 2 (edge, activehi) ioapic0: intpin 3 -> irq 3 (edge, activehi) ioapic0: intpin 4 -> irq 4 (edge, activehi) ioapic0: intpin 5 -> irq 5 (edge, activehi) ioapic0: intpin 6 -> irq 6 (edge, activehi) ioapic0: intpin 7 -> irq 7 (edge, activehi) ioapic0: intpin 8 -> irq 8 (edge, activehi) ioapic0: intpin 9 -> irq 9 (edge, activehi) ioapic0: intpin 10 -> irq 10 (edge, activehi) ioapic0: intpin 11 -> irq 11 (edge, activehi) ioapic0: intpin 12 -> irq 12 (edge, activehi) ioapic0: intpin 13 -> irq 13 (edge, activehi) ioapic0: intpin 14 -> irq 14 (edge, activehi) ioapic0: intpin 15 -> irq 15 (edge, activehi) ioapic0: intpin 16 -> irq 16 (level, activelo) ioapic0: intpin 17 -> irq 17 (level, activelo) ioapic0: intpin 18 -> irq 18 (level, activelo) ioapic0: intpin 19 -> irq 19 (level, activelo) ioapic0: intpin 20 -> irq 20 (level, activelo) ioapic0: intpin 21 -> irq 21 (level, activelo) ioapic0: intpin 22 -> irq 22 (level, activelo) ioapic0: intpin 23 -> irq 23 (level, activelo) MADT: intr override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 ioapic0: intpin 2 polarity: active-hi ioapic0: intpin 2 trigger: edge lapic1: Routing NMI -> LINT1 lapic1: LINT1 trigger: edge lapic1: LINT1 polarity: active-hi lapic0: Routing NMI -> LINT1 lapic0: LINT1 trigger: edge lapic0: LINT1 polarity: active-hi ioapic0 <Version 1.1> irqs 0-23 on motherboard cpu0 BSP: ID: 0x01000000 VER: 0x00040010 LDR: 0x02000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff null: <null device, zero device> random: <entropy source> mem: <memory & I/O> Pentium Pro MTRR support enabled cpu0 on motherboard cpu1 on motherboard npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <PTLTD RSDT> on motherboard acpi0: [GIANT-LOCKED] pci_open(1): mode 1 addr port (0x0cf8) is 0x80000818 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=700c1022) pcibios: BIOS version 2.10 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 7 func 3 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 7 func 0 acpi0: Power Button (fixed) acpi0: Sleep Button (fixed) ACPI timer looks GOOD min = 4, max = 5, width = 1 ACPI timer looks GOOD min = 4, max = 5, width = 1 ACPI timer looks GOOD min = 4, max = 5, width = 1 ACPI timer looks GOOD min = 4, max = 5, width = 1 ACPI timer looks GOOD min = 4, max = 5, width = 1 ACPI timer looks GOOD min = 4, max = 5, width = 1 ACPI timer looks GOOD min = 4, max = 5, width = 1 ACPI timer looks GOOD min = 4, max = 5, width = 1 ACPI timer looks GOOD min = 4, max = 5, width = 1 ACPI timer looks GOOD min = 4, max = 5, width = 1 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0 mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) acpi_cpu0: <CPU> port 0x530-0x537 on acpi0 mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) acpi_cpu1: <CPU> port 0x530-0x537 on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0x8080-0x80ff,0x8000-0x807f,0xcf8-0xcff iomem 0xd8000-0xdbfff on acpi0 ---- initial configuration ------------------------ ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base f4000000, size 26, enabled map[14]: type 3, range 32, base f2100000, size 12, enabled map[18]: type 4, range 32, base 00001020, size 2, port disabled found-> vendor=0x1022, dev=0x700c, revid=0x11 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x2230, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x700d, revid=0x00 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0007, statreg=0x0220, cachelnsz=0 (dwords) lattimer=0x63 (2970 ns), mingnt=0x0c (3000 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7440, revid=0x05 bus=0, slot=7, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000f000, size 4, enabled found-> vendor=0x1022, dev=0x7441, revid=0x04 bus=0, slot=7, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7443, revid=0x03 bus=0, slot=7, func=3 class=06-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x16 (660 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 4, range 32, base 00001038, size 3, enabled map[14]: type 4, range 32, base 00001030, size 2, enabled map[18]: type 4, range 32, base 00001028, size 3, enabled map[1c]: type 4, range 32, base 00001024, size 2, enabled map[20]: type 4, range 32, base 00001010, size 4, enabled map[24]: type 1, range 32, base f0000000, size 14, enabled pcib0: matched entry for 0.8.INTA (src ) pcib0: device is hardwired to IRQ 20 found-> vendor=0x105a, dev=0x4d68, revid=0x02 bus=0, slot=8, func=0 class=01-80-85, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0430, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x12 (4500 ns) intpin=a, irq=20 powerspec 1 supports D0 D1 D3 current D0 found-> vendor=0x1044, dev=0xa500, revid=0x02 bus=0, slot=9, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0006, statreg=0x0290, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) map[10]: type 3, range 32, base f8000000, size 26, enabled pcib0: matched entry for 0.9.INTA (src ) pcib0: device is hardwired to IRQ 21 found-> vendor=0x1044, dev=0xa501, revid=0x02 bus=0, slot=9, func=1 class=0e-00-01, hdrtype=0x00, mfdev=1 cmdreg=0x0016, statreg=0x0290, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x01 (250 ns), maxlat=0x01 (250 ns) intpin=a, irq=21 powerspec 2 supports D0 D3 current D0 found-> vendor=0x1022, dev=0x7448, revid=0x05 bus=0, slot=16, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0017, statreg=0x2220, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) agp0: <AMD 762 host to AGP bridge> port 0x1020-0x1023 mem 0xf2100000-0xf2100fff,0xf4000000-0xf7ffffff at device 0.0 on pci0 agp0: allocating GATT for aperture of size 64M agp0: gatt -> ag_pdir 0x28c000 agp0: allocating GATT for 16384 AGP page entries pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xf000-0xfff pcib1: memory decode 0xf1000000-0xf1ffffff pcib1: prefetched decode 0xfc000000-0xfcffffff ---- initial configuration ------------------------ ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 map[10]: type 1, range 32, base f1000000, size 24, enabled map[14]: type 3, range 32, base fc000000, size 24, enabled pcib1: matched entry for 1.5.INTA (src ) pcib1: device is hardwired to IRQ 18 found-> vendor=0x10de, dev=0x0020, revid=0x04 bus=1, slot=5, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0003, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns) intpin=a, irq=18 powerspec 1 supports D0 D3 current D0 pci1: <display, VGA> at device 5.0 (no driver attached) isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <AMD 768 UDMA100 controller> port 0xf000-0xf00f at device 7.1 on pci0 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata0-master: stat=0x80 err=0x80 lsb=0x80 msb=0x80 ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb ata0-slave: stat=0x00 err=0x00 lsb=0x00 msb=0x00 ata0: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: reset tp1 mask=03 ostat0=10 ostat1=01 ata1-master: stat=0x10 err=0x01 lsb=0x14 msb=0xeb ata1-slave: stat=0x01 err=0x01 lsb=0x14 msb=0xeb ata1: reset tp2 mask=03 stat0=10 stat1=01 devices=0xc<ATAPI_SLAVE,ATAPI_MASTER> ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) atapci1: <Promise PDC20268 UDMA100 controller> port 0x1010-0x101f,0x1024-0x1027,0x1028-0x102f,0x1030-0x1033,0x1038-0x103f mem 0xf0000000-0xf0003fff irq 20 at device 8.0 on pci0 atapci1: [MPSAFE] ata2: reset tp1 mask=03 ostat0=50 ostat1=00 ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata2-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata2: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata2: at 0x1038 on atapci1 ata2: [MPSAFE] ata3: reset tp1 mask=03 ostat0=50 ostat1=00 ata3-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata3-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata3: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata3: at 0x1028 on atapci1 ata3: [MPSAFE] pcib2: <PCI-PCI bridge> at device 9.0 on pci0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0x0-0x0 pcib2: memory decode 0x100000-0xfffff pcib2: prefetched decode 0x100000-0xfffff pci2: <PCI bus> on pcib2 pci2: physical bus=2 asr0: <Adaptec Caching SCSI RAID> mem 0xf8000000-0xfbffffff irq 21 at device 9.1 on pci0 asr0: major=154 asr0: [GIANT-LOCKED] asr0: ADAPTEC 2400A FW Rev. 370L, 4 channel, 256 CCBs, Protocol I2O pcib3: <ACPI PCI-PCI bridge> at device 16.0 on pci0 pcib3: secondary bus 3 pcib3: subordinate bus 3 pcib3: I/O decode 0x2000-0x2fff pcib3: memory decode 0xf2000000-0xf20fffff pcib3: prefetched decode 0xfff00000-0xfffff ---- initial configuration ------------------------ ---- before setting priority for links ------------ ---- before fixup boot-disabled links ------------- ---- after fixup boot-disabled links -------------- ---- arbitrated configuration --------------------- pci3: <ACPI PCI bus> on pcib3 pci3: physical bus=3 map[10]: type 1, range 32, base f2010000, size 12, enabled pcib3: matched entry for 3.0.INTD (src ) pcib3: device is hardwired to IRQ 19 found-> vendor=0x1022, dev=0x7449, revid=0x07 bus=3, slot=0, func=0 class=0c-03-10, hdrtype=0x00, mfdev=0 cmdreg=0x0017, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns) intpin=d, irq=19 map[10]: type 4, range 32, base 00002000, size 8, enabled map[14]: type 1, range 32, base f2011000, size 12, enabled pcib3: matched entry for 3.4.INTA (src ) pcib3: device is hardwired to IRQ 16 found-> vendor=0x9004, dev=0x5078, revid=0x03 bus=3, slot=4, func=0 class=01-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0017, statreg=0x0290, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x04 (1000 ns) intpin=a, irq=16 powerspec 1 supports D0 D3 current D0 map[10]: type 4, range 32, base 00002480, size 6, enabled pcib3: matched entry for 3.5.INTA (src ) pcib3: device is hardwired to IRQ 17 found-> vendor=0x1274, dev=0x5000, revid=0x00 bus=3, slot=5, func=0 class=04-01-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0400, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x0c (3000 ns), maxlat=0x80 (32000 ns) intpin=a, irq=17 map[10]: type 1, range 64, base f2000000, size 16, enabled pcib3: matched entry for 3.6.INTA (src ) pcib3: device is hardwired to IRQ 18 found-> vendor=0x173b, dev=0x03ea, revid=0x15 bus=3, slot=6, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0016, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns) intpin=a, irq=18 powerspec 2 supports D0 D3 current D0 MSI supports 8 messages, 64 bit map[10]: type 4, range 32, base 00002400, size 7, enabled map[14]: type 1, range 32, base f2012000, size 7, enabled pcib3: matched entry for 3.8.INTA (src ) pcib3: device is hardwired to IRQ 19 found-> vendor=0x10b7, dev=0x9200, revid=0x78 bus=3, slot=8, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0017, statreg=0x0210, cachelnsz=16 (dwords) lattimer=0x50 (2400 ns), mingnt=0x0a (2500 ns), maxlat=0x0a (2500 ns) intpin=a, irq=19 powerspec 2 supports D0 D1 D2 D3 current D0 pci3: <serial bus, USB> at device 0.0 (no driver attached) ahc0: <Adaptec 2902/04/10/15/20C/30C SCSI adapter> port 0x2000-0x20ff mem 0xf2011000-0xf2011fff irq 16 at device 4.0 on pci3 ahc0: Defaulting to MEMIO off pcib3: device ahc0 requested decoded I/O range 0x2000-0x20ff ahc0: No SEEPROM available. ahc0: Host Adapter Bios disabled. Using default SCSI device parameters ahc0: Downloading Sequencer Program... 457 instructions downloaded ahc0: Features 0x10100, Bugs 0x35, Flags 0x8401f44 ahc0: [GIANT-LOCKED] aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs pcm0: <AudioPCI ES1370> port 0x2480-0x24bf irq 17 at device 5.0 on pci3 pcib3: device pcm0 requested decoded I/O range 0x2480-0x24bf pcm0: [GIANT-LOCKED] pcm0: sndbuf_setmap 2e3000, 1000; 0xc740f000 -> 2e3000 pcm0: sndbuf_setmap 7d672000, 1000; 0xc743e000 -> 7d672000 bge0: <Altima AC9100 Gigabit Ethernet, ASIC rev. 0x105> mem 0xf2000000-0xf200ffff irq 18 at device 6.0 on pci3 pcib3: device bge0 requested decoded memory range 0xf2000000-0xf200ffff miibus0: <MII bus> on bge0 brgphy0: <BCM5701 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge0: bpf attached bge0: Ethernet address: 00:09:5b:1b:90:91 bge0: [GIANT-LOCKED] xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0x2400-0x247f mem 0xf2012000-0xf201207f irq 19 at device 8.0 on pci3 pcib3: device xl0 requested decoded memory range 0xf2012000-0xf201207f xl0: using memory mapped I/O xl0: media options word: a xl0: found MII/AUTO miibus1: <MII bus> on xl0 ukphy0: <Generic IEEE 802.3u media interface> on miibus1 ukphy0: OUI 0x00105a, model 0x0000, rev. 0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl0: bpf attached xl0: Ethernet address: 00:e0:81:21:83:70 xl0: [GIANT-LOCKED] mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) psmcpnp0 irq 12 on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 atkbd0: [GIANT-LOCKED] psm0: current command byte:0047 psm0: failed to reset the aux device. mss_probe: no address given, try 0x530 mss_detect, busy still set (0xff) sio0: irq maps: 0xe001 0xe011 0xe001 0xe001 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A sio1: irq maps: 0xe001 0xe009 0xe001 0xe001 sio1 port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ppc0: using extended I/O port range ppc0: ECP SPP ECP+EPP SPP ppc0 port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/9 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 plip0: bpf attached lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold mss_detect, busy still set (0xff) mss_detect, busy still set (0xff) mss_detect, busy still set (0xff) mss_detect, busy still set (0xff) mss_detect, busy still set (0xff) mss_detect, busy still set (0xff) ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it ppc: ppc0 already exists; skipping it sio: sio0 already exists; skipping it sio: sio1 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <Option ROMs> at iomem 0xe0000-0xe3fff,0xca800-0xd07ff,0xc8800-0xca7ff,0xc8000-0xc87ff,0xc0000-0xc7fff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0e 0f 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered Timecounter "TSC" frequency 1666735157 Hz quality -100 Timecounters tick every 1.000 msec lo0: bpf attached ata0-master: pio=0x0c wdma=0x22 udma=0x44 cable=80pin ata0-master: setting PIO4 on AMD 768 chip ata0-master: setting UDMA66 on AMD 768 chip acd0: <Pioneer DVD-ROM ATAPIModel DVD-117 0107/E1.07> DVDROM drive at ata0 as master acd0: read 6894KB/s (6894KB/s), 256KB buffer, UDMA66 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, packet acd0: Writes: acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc ata1-slave: FAILURE - ATAPI_IDENTIFY no interrupt ata1-slave: FAILURE - ATAPI_IDENTIFY status=1<ERROR> error=1<ILLEGAL_LENGTH> LBA=0 ata1-slave: FAILURE - ATAPI_IDENTIFY no interrupt ata1-slave: FAILURE - ATAPI_IDENTIFY status=1<ERROR> error=1<ILLEGAL_LENGTH> LBA=0 ata1-master: pio=0x0c wdma=0x22 udma=0xffffffff cable=40pin ata1-master: setting PIO4 on AMD 768 chip ata1-master: setting WDMA2 on AMD 768 chip ast0: <Seagate STT20000A/8A51> tape drive at ata1 as master ast0: 1000KB/s, transfer limit 108 blks, 324KB buffer, WDMA2 ast0: Medium: none, readonly, qfa, ecc, 512b ata2-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata2-master: setting PIO4 on Promise PDC20268 chip ata2-master: setting UDMA100 on Promise PDC20268 chip ad4: <WDC WD1200JB-00DUA3/75.13B75> ATA-6 disk at ata2-master ad4: 114473MB (234441648 sectors), 232581 C, 16 H, 63 S, 512 B ad4: 16 secs/int, 1 depth queue, UDMA100 GEOM: new disk ad4 ata3-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata3-master: setting PIO4 on Promise PDC20268 chip ata3-master: setting UDMA100 on Promise PDC20268 chip ad6: <IC35L060AVER07-0/ER6OA46A> ATA-5 disk at ata3-master ad6: 58644MB (120103200 sectors), 119150 C, 16 H, 63 S, 512 B ad6: 16 secs/int, 1 depth queue, UDMA100 Waiting 5 seconds for SCSI devices to settle (noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:234436482 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad4s1, start 32256 length 120031478784 end 120031511039 GEOM: new disk ad6 GEOM: Configure ad4s1a, start 0 length 536870912 end 536870911 GEOM: Configure ad4s1b, start 536870912 length 2147483648 end 2684354559 GEOM: Configure ad4s1c, start 0 length 120031478784 end 120031478783 GEOM: Configure ad4s1d, start 2684354560 length 536870912 end 3221225471 GEOM: Configure ad4s1e, start 3221225472 length 536870912 end 3758096383 GEOM: Configure ad4s1f, start 3758096384 length 116273382400 end 120031478783 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/11/63 s:63 l:120101877 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad6s1, start 32256 length 61492161024 end 61492193279 GEOM: Configure ad6s1c, start 0 length 61492161024 end 61492161023 GEOM: Configure ad6s1d, start 0 length 61492161024 end 61492161023 (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 0, offset 0 (ahc0:A:4:0): Target Initiated SDTR (ahc0:A:4:0): Sending SDTR period 45, offset 0 (probe30:ahc0:0:2:0): error 22 (probe30:ahc0:0:2:0): Unretryable Error (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f ahc0: target 4 synchronous at 10.0MHz, offset = 0xf (ahc0:A:2:0): Sending SDTR period 19, offset f (ahc0:A:2:0): Received SDTR period 19, offset f Filtered to period 19, offset f ahc0: target 2 synchronous at 10.0MHz, offset = 0xf (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (ahc0:A:2:0): Sending SDTR period 19, offset f (ahc0:A:2:0): Received SDTR period 19, offset f Filtered to period 19, offset f pass0 at asr0 bus 0 target 0 lun 0 pass0: <ADAPTEC RAID-5 370L> Fixed Direct Access SCSI-2 device pass0: Serial Number + pass0: Tagged Queueing Enabled pass1 at ahc0 bus 0 target 2 lun 0 pass1: <YAMAHA CRW8824S 1.00> Removable CD-ROM SCSI-2 device pass1: 10.000MB/s transfers (10.000MHz, offset 15) pass2 at ahc0 bus 0 target 4 lun 0 pass2: <Quantum DLT4000 CPQ DRV D473> Removable Sequential Access SCSI-2 device pass2: Serial Number CX922M1222 pass2: 10.000MB/s transfers (10.000MHz, offset 15) sa0 at ahc0 bus 0 target 4 lun 0 sa0: <Quantum DLT4000 CPQ DRV D473> Removable Sequential Access SCSI-2 device sa0: Serial Number CX922M1222 sa0: 10.000MB/s transfers (10.000MHz, offset 15) da0 at asr0 bus 0 target 0 lun 0 da0: <ADAPTEC RAID-5 370L> Fixed Direct Access SCSI-2 device da0: Serial Number + da0: Tagged Queueing Enabled da0: 343419MB (703322112 512 byte sectors: 255H 63S/T 43779C) (ahc0:A:2:0): Sending SDTR period 19, offset f GEOM: new disk cd0 GEOM: new disk da0 SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x00000000 VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff ioapic0: routing intpin 1 (IRQ 1) to cluster 0 ioapic0: routing intpin 3 (IRQ 3) to cluster 0 ioapic0: routing intpin 4 (IRQ 4) to cluster 0 ioapic0: routing intpin 6 (IRQ 6) to cluster 0 ioapic0: routing intpin 7 (IRQ 7) to cluster 0 ioapic0: routing intpin 8 (IRQ 8) to cluster 0 ioapic0: routing intpin 9 (IRQ 9) to cluster 0 ioapic0: routing intpin 13 (IRQ 13) to cluster 0 ioapic0: routing intpin 14 (IRQ 14) to cluster 0 ioapic0: routing intpin 15 (IRQ 15) to cluster 0 ioapic0: routing intpin 16 (IRQ 16) to cluster 0 ioapic0: routing intpin 17 (IRQ 17) to cluster 0 ioapic0: routing intpin 18 (IRQ 18) to cluster 0 ioapic0: routing intpin 19 (IRQ 19) to cluster 0 ioapic0: routing intpin 20 (IRQ 20) to cluster 0 ioapic0: routing intpin 21 (IRQ 21) to cluster 0 (ahc0:A:2:0): Received SDTR period 19, offset f Filtered to period 19, offset f (cd0:ahc0:0:2:0): error 6 (cd0:ahc0:0:2:0): Unretryable Error cd0 at ahc0 bus 0 target 2 lun 0 cd0: <YAMAHA CRW8824S 1.00> Removable CD-ROM SCSI-2 device cd0: 10.000MB/s transfers (10.000MHz, offset 15) cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed (ahc0:A:2:0): Sending SDTR period 19, offset f (ahc0:A:2:0): Received SDTR period 19, offset f Filtered to period 19, offset f (cd0:ahc0:0:2:0): error 6 (cd0:ahc0:0:2:0): Unretryable Error (ahc0:A:2:0): Sending SDTR period 19, offset f (ahc0:A:2:0): Received SDTR period 19, offset f Filtered to period 19, offset f (cd0:ahc0:0:2:0): error 6 (cd0:ahc0:0:2:0): Unretryable Error (ahc0:A:2:0): Sending SDTR period 19, offset f (ahc0:A:2:0): Received SDTR period 19, offset f Filtered to period 19, offset f (cd0:ahc0:0:2:0): error 6 (cd0:ahc0:0:2:0): Unretryable Error (ahc0:A:2:0): Sending SDTR period 19, offset f (ahc0:A:2:0): Received SDTR period 19, offset f Filtered to period 19, offset f (cd0:ahc0:0:2:0): error 6 (cd0:ahc0:0:2:0): Unretryable Error [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:703309572 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure da0s1, start 32256 length 360094500864 end 360094533119 GEOM: Configure da0s1c, start 0 length 360094500864 end 360094500863 GEOM: Configure da0s1d, start 0 length 360094500864 end 360094500863 Mounting root from ufs:/dev/ad4s1a start_init: trying /sbin/init xl0: transmission error: 90 xl0: tx underrun, increasing tx start threshold to 120 bytes xl0: transmission error: 90 xl0: tx underrun, increasing tx start threshold to 180 bytes xl0: transmission error: 90 xl0: tx underrun, increasing tx start threshold to 240 bytes xl0: transmission error: 90 xl0: tx underrun, increasing tx start threshold to 300 bytes xl0: transmission error: 90 xl0: tx underrun, increasing tx start threshold to 360 bytes [xenon:~]$ pciconf -l -v agp0_at_pci0:0:0: class=0x060000 card=0x00000000 chip=0x700c1022 rev=0x11 hdr=0x00 vendor = 'Advanced Micro Devices (AMD)' device = 'AMD-762 CPU to PCI Bridge (SMP chipset)' class = bridge subclass = HOST-PCI pcib1_at_pci0:1:0: class=0x060400 card=0x00000000 chip=0x700d1022 rev=0x00 hdr=0x01 vendor = 'Advanced Micro Devices (AMD)' device = 'AMD-762 CPU to PCI Bridge (AGP 4x)' class = bridge subclass = PCI-PCI isab0_at_pci0:7:0: class=0x060100 card=0x00000000 chip=0x74401022 rev=0x05 hdr=0x00 vendor = 'Advanced Micro Devices (AMD)' device = 'AMD-768 PCI to ISA/LPC Bridge' class = bridge subclass = PCI-ISA atapci0_at_pci0:7:1: class=0x01018a card=0x74411022 chip=0x74411022 rev=0x04 hdr=0x00 vendor = 'Advanced Micro Devices (AMD)' device = 'AMD-768 EIDE Controller' class = mass storage subclass = ATA none0_at_pci0:7:3: class=0x068000 card=0x74431022 chip=0x74431022 rev=0x03 hdr=0x00 vendor = 'Advanced Micro Devices (AMD)' device = 'AMD-768 System Management' class = bridge subclass = PCI-unknown atapci1_at_pci0:8:0: class=0x018085 card=0x4d68105a chip=0x4d68105a rev=0x02 hdr=0x00 vendor = 'Promise Technology Inc' device = 'PDC20268 Ultra100 TX2 EIDE Controller' class = mass storage pcib2_at_pci0:9:0: class=0x060400 card=0x00000068 chip=0xa5001044 rev=0x02 hdr=0x01 vendor = 'Adaptec (Formerly: Distributed Processing Technology (DPT))' device = 'PCI Bridge' class = bridge subclass = PCI-PCI asr0_at_pci0:9:1: class=0x0e0001 card=0xc05a1044 chip=0xa5011044 rev=0x02 hdr=0x00 vendor = 'Adaptec (Formerly: Distributed Processing Technology (DPT))' device = 'I2O SmartRAID V Controller' pcib3_at_pci0:16:0: class=0x060400 card=0x00000000 chip=0x74481022 rev=0x05 hdr=0x01 vendor = 'Advanced Micro Devices (AMD)' device = 'AMD-768 PCI Bridge' class = bridge subclass = PCI-PCI none1_at_pci1:5:0: class=0x030000 card=0x10151102 chip=0x002010de rev=0x04 hdr=0x00 vendor = 'NVIDIA Corporation' device = 'Riva TNT GUI+3D Accelerator [NV4]' class = display subclass = VGA none2_at_pci3:0:0: class=0x0c0310 card=0x00000000 chip=0x74491022 rev=0x07 hdr=0x00 vendor = 'Advanced Micro Devices (AMD)' device = 'AMD-768 USB Controller' class = serial bus subclass = USB ahc0_at_pci3:4:0: class=0x010000 card=0x78509004 chip=0x50789004 rev=0x03 hdr=0x00 vendor = 'Adaptec Inc' device = 'AVA-2902I/E,AVA-2904,AVA-2910 (AIC-7850P) Fast/Wide SCSI II' class = mass storage subclass = SCSI pcm0_at_pci3:5:0: class=0x040100 card=0x4c4c4942 chip=0x50001274 rev=0x00 hdr=0x00 vendor = 'Creative (Was: Ensoniq)' device = 'ES1370 AudioPCI' class = multimedia subclass = audio bge0_at_pci3:6:0: class=0x020000 card=0x302a1385 chip=0x03ea173b rev=0x15 hdr=0x00 vendor = 'Altima Communications Inc' class = network subclass = ethernet xl0_at_pci3:8:0: class=0x020000 card=0x246610f1 chip=0x920010b7 rev=0x78 hdr=0x00 vendor = '3COM Corp, Networking Division' device = '3C905C-TX Fast EtherLink for PC Management NIC' class = network subclass = ethernet -- Peter Wood <peter_at_alastria.net> :: Tel +44 7974 799440Received on Fri Apr 02 2004 - 13:48:01 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:49 UTC