Doug, Thanks for the quick response... I've been trying a couple combinations without any luck..... FYI: My goal is a Promise RAID10 (need two more drives) and Intel RAID0, with the Promise being the daily use and the Intel being a weekly snapshot. I've got another machine offsite performing daily rsync backups. Doug White wrote: > On Thu, 8 Apr 2004, Jeff Doolittle wrote: > > >>I've seen eMails regarding ICH5R support on other motherboards being >>added, is there plans to add support for the ASUS P4C800-E Deluxe? > > > Can you try this without ACPI? THe Asus P4*800 series are known to have > bad ACPI code. > I've rebooted and selected option #2 from the "boot menu" which indicates ACPI is diabled, but the kernel dumps on errors 9 and 12 while booting. I disabled "ACPI 2.0 Support", "ACPI APIC Support", & "BIOS --> AML ACPI table" and if I boot normal or use option #2 the kernel dumps on errors 9 and 12 while booting. I even disabled hyper-threading, re-enabled the above, selected option #2 and still the kernel dumps while booting. In all instances after the kernel dump I'm placed in a debug mode.... I'm also running the latest version of ASUS BIOS (v1016) for the m/b if that makes a difference. > >>I tried both FreeBSD v5.2.1 & am now updating to current on a daily >>basis hoping the following error will be address: >> >> ad12: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA = xxxx >>or >> ad10: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA = xxxx >>and >> the machine is hung, requiring a hard reset. >> >>The following are from dmesg: >> >>FreeBSD 5.2-CURRENT #0: Thu Apr 8 13:27:36 EDT 2004 >> root_at_saturn.kingsquarry.net:/usr/obj/usr/src/sys/GENERIC >>..... >>Timecounter "i8254" frequency 1193182 Hz quality 0 >>CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2398.85-MHz 686-class CPU) >> Origin = "GenuineIntel" Id = 0xf25 Stepping = 5 >> >>Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> >> Hyperthreading: 2 logical CPUs >>real memory = 536018944 (511 MB) >>avail memory = 514789376 (490 MB) >>..... >>atapci0: <Promise PDC20378 SATA150 controller> port >>0xd880-0xd8ff,0xdfa0-0xdfaf,0xdf00-0xdf3f mem >>0xfeac0000-0xfeadffff,0xfeafe000-0xfeafefff irq 23 at device 4.0 on pci3 >>ata2: at 0xfeafe000 on atapci0 >>ata3: at 0xfeafe000 on atapci0 >>ata4: at 0xfeafe000 on atapci0 >>isab0: <PCI-ISA bridge> at device 31.0 on pci0 >>isa0: <ISA bus> on isab0 >>atapci1: <Intel ICH5 UDMA100 controller> port >>0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0 >>ata0: at 0x1f0 irq 14 on atapci1 >>ata1: at 0x170 irq 15 on atapci1 >>atapci2: <Intel ICH5 SATA150 controller> port >>0xef90-0xef9f,0xefa8-0xefab,0xefa0-0xefa7,0xefac-0xefaf,0xefe0-0xefe7 >>irq 18 at device 31.2 on pci0 >>ata5: at 0xefe0 on atapci2 >>ata6: at 0xefa0 on atapci2 >>..... >>ad0: 19092MB <ST320413A> [38792/16/63] at ata0-master UDMA100 >>acd0: CDRW <48X12X50 CD-RW 1.04 20021101> at ata1-master PIO4 >>ad4: 190782MB <WDC WD2000JD-00FYB0> [387621/16/63] at ata2-master UDMA100 >>ad6: 190782MB <WDC WD2000JD-00FYB0> [387621/16/63] at ata3-master UDMA100 >>em0: Link is up 100 Mbps Full Duplex >>ad10: 190782MB <WDC WD2000JD-00FYB0> [387621/16/63] at ata5-master UDMA100 >>ad12: 190782MB <WDC WD2000JD-00FYB0> [387621/16/63] at ata6-master UDMA100 >>ar0: 381564MB <ATA RAID0 array> [48642/255/63] status: READY subdisks: >> disk0 READY on ad4 at ata2-master >> disk1 READY on ad6 at ata3-master >>ar1: 381564MB <ATA RAID0 array> [48642/255/63] status: READY subdisks: >> disk0 READY on ad10 at ata5-master >> disk1 READY on ad12 at ata6-master >> >>NOTE #1: ar0 is a Promise created RAID array. >>NOTE #2: at1 is a atacontrol created RAID array, because the BIOS >>created is not recognized. >> >>Basically the machine crashed when I run rsync from the Promise raid >>drives to the Intel raid drives. In the past I could copy between 1 - >>2gig and it would hang with the above error messages, except yesterday's >>build dumped me in debug mode, today's build is the first I have seen it >>acknowlegde the Intel ICH5 SATA150 controller and it errors out almost >>immediately after starting rsync. >> >>Is there more information I can/should provide to help resolve this >>problem? I apologize, this is the first time I've ever had a "problem" >>with FreeBSD since I started using it at v2.2.7.... >> >> Thanks. >> >> - Jeff >> >> >> >>Thanks... >>_______________________________________________ >>freebsd-current_at_freebsd.org mailing list >>http://lists.freebsd.org/mailman/listinfo/freebsd-current >>To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org" >> > >Received on Thu Apr 08 2004 - 16:29:06 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:50 UTC