Re: ASUS P4C800-E Deluxe and ICH5R support

Try disabling APIC at the boot prompt.

set hint.apic.0.disabled=1

On Thu, 08 Apr 2004 19:54:36 -0400
Jeff Doolittle <jdoolittle_at_kingsquarry.net> wrote:

> I've seen eMails regarding ICH5R support on other motherboards being 
> added, is there plans to add support for the ASUS P4C800-E Deluxe?
> 
> I tried both FreeBSD v5.2.1 & am now updating to current on a daily 
> basis hoping the following error will be address:
> 
>     ad12: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA = xxxx
> or
>     ad10: TIMEOUT - WRITE_DMA retrying (2 retries left) LBA = xxxx
> and
>     the machine is hung, requiring a hard reset.
> 
> The following are from dmesg:
> 
> FreeBSD 5.2-CURRENT #0: Thu Apr  8 13:27:36 EDT 2004
>     root_at_saturn.kingsquarry.net:/usr/obj/usr/src/sys/GENERIC
> .....
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2398.85-MHz 686-class CPU)
>   Origin = "GenuineIntel"  Id = 0xf25  Stepping = 5
>   
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,
> PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,P
> BE>
>   Hyperthreading: 2 logical CPUs
> real memory  = 536018944 (511 MB)
> avail memory = 514789376 (490 MB)
> .....
> atapci0: <Promise PDC20378 SATA150 controller> port 
> 0xd880-0xd8ff,0xdfa0-0xdfaf,0xdf00-0xdf3f mem 
> 0xfeac0000-0xfeadffff,0xfeafe000-0xfeafefff irq 23 at device 4.0 on
> pci3 ata2: at 0xfeafe000 on atapci0
> ata3: at 0xfeafe000 on atapci0
> ata4: at 0xfeafe000 on atapci0
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci1: <Intel ICH5 UDMA100 controller> port 
> 0xfc00-0xfc0f,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci1
> ata1: at 0x170 irq 15 on atapci1
> atapci2: <Intel ICH5 SATA150 controller> port 
> 0xef90-0xef9f,0xefa8-0xefab,0xefa0-0xefa7,0xefac-0xefaf,0xefe0-0xefe7 
> irq 18 at device 31.2 on pci0
> ata5: at 0xefe0 on atapci2
> ata6: at 0xefa0 on atapci2
> .....
> ad0: 19092MB <ST320413A> [38792/16/63] at ata0-master UDMA100
> acd0: CDRW <48X12X50 CD-RW 1.04 20021101> at ata1-master PIO4
> ad4: 190782MB <WDC WD2000JD-00FYB0> [387621/16/63] at ata2-master
> UDMA100 ad6: 190782MB <WDC WD2000JD-00FYB0> [387621/16/63] at
> ata3-master UDMA100 em0: Link is up 100 Mbps Full Duplex
> ad10: 190782MB <WDC WD2000JD-00FYB0> [387621/16/63] at ata5-master
> UDMA100 ad12: 190782MB <WDC WD2000JD-00FYB0> [387621/16/63] at
> ata6-master UDMA100 ar0: 381564MB <ATA RAID0 array> [48642/255/63]
> status: READY subdisks:
>  disk0 READY on ad4 at ata2-master
>  disk1 READY on ad6 at ata3-master
> ar1: 381564MB <ATA RAID0 array> [48642/255/63] status: READY subdisks:
>  disk0 READY on ad10 at ata5-master
>  disk1 READY on ad12 at ata6-master
> 
> NOTE #1:  ar0 is a Promise created RAID array.
> NOTE #2:  at1 is a atacontrol created RAID array, because the BIOS 
> created is not recognized.
> 
> Basically the machine crashed when I run rsync from the Promise raid 
> drives to the Intel raid drives.  In the past I could copy between 1 -
> 
> 2gig and it would hang with the above error messages, except
> yesterday's build dumped me in debug mode, today's build is the first
> I have seen it acknowlegde the Intel ICH5 SATA150 controller and it
> errors out almost immediately after starting rsync.
> 
> Is there more information I can/should provide to help resolve this 
> problem?  I apologize, this is the first time I've ever had a
> "problem" with FreeBSD since I started using it at v2.2.7....
> 
>     Thanks.
> 
>        - Jeff
> 
> 
> 
> Thanks...
> _______________________________________________
> freebsd-current_at_freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-current
> To unsubscribe, send any mail to
> "freebsd-current-unsubscribe_at_freebsd.org"