Re: Re: cardbus problems

From: Francisco Alves Cabrita <francisco_at_nortenet.pt>
Date: Sun, 18 Apr 2004 19:37:20 +0100
> In message: <1082226317.834.12.camel_at_zarcon.homeunix.net>
>             Francisco Alves Cabrita <francisco_at_nortenet.pt> writes:
> : hello
> : i'm running (i386)5-CURRENT and in this "nightly" buildwold ,, my
> : cardbus (ethernet pcmcia ovislink chipset rl) didnt get enabled""
> : 
> : 
> : this was the message during boot:
> : 
> : cbb0: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.0 on pci0
> : cbb0: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0
> : cardbus0: <CardBus bus> on cbb0
> : pccard0: <16-bit PCCard bus> on cbb0
> : cbb0: bad Vcc request. ctrl=0xf000ef08, status=0xf000e2c3
> : cbb_power: 0V
> : cbb1: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.1 on pci0
> : cbb1: Lazy allocation of 0x1000 bytes rid 0x10 type 3 at 0x1000
> : cardbus1: <CardBus bus> on cbb1
> : pccard1: <16-bit PCCard bus> on cbb1
> : cbb1: bad Vcc request. ctrl=0x7720700, status=0x76f076c
> : cbb_power: 0V
> : 
> : can some one give a tip !!! 
> 
> Please submit an older, working dmesg.  I think I know what's going
> on, but w/o that, I can't be sure.
> 
> Since the cbb is on pci0, I think that you might have an non-ACPI
> system.  Especially since the ToPIC95B is a relatively old chip.  My
> guess is that this is a 100-166MHz Pentium system.
> 
> Warner

Hellow Warner, thank for you response.

Yes, you are almost right, is not an 100-166 Pentium , but and Toshiba
(4300 series) Laptop 600Mhz with ACPI disabled for performence reasons,
but here goes the boot message when was working:

cbb0: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.0 on pci0
cardbus0: <CardBus bus> on cbb0
pccard0: <16-bit PCCard bus> on cbb0
cbb1: <ToPIC95B PCI-CardBus Bridge> irq 11 at device 11.1 on pci0
cardbus1: <CardBus bus> on cbb1
pccard1: <16-bit PCCard bus> on cbb1

and the result:

rl0: <RealTek 8139 10/100BaseTX> port 0x1000-0x10ff mem
0x88002000-0x880021ff irq 11 at device 0.0 on cardbus1
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: Ethernet address: 00:10:60:75:66:fc
rl0: [GIANT-LOCKED]

since I installed 5.X here, i disabled the ACPI module, and didnt have
any hardware problems until now, but i will tunr it on to see what
appen.

[] thanks
Francisco
Received on Sun Apr 18 2004 - 09:37:32 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:51 UTC