Hello I've seen your message on the internet and I've the same problem trying to install a pcmcia modem in soekris 4511 : Did you resolve it ? Here is my dmesg : Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2.1-RELEASE #10: Thu Aug 26 10:52:28 GMT 2004 root_at_flanagan.altea.ca:/usr/src/sys/i386/compile/ALTEBOX Preloaded elf kernel "/boot/kernel/kernel" at 0xc0716000. Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: AMD Enhanced Am486DX4/Am5x86 Write-Back (486-class CPU) Origin = "AuthenticAMD" Id = 0x494 Stepping = 4 Features=0x1<FPU> real memory = 67108864 (64 MB) avail memory = 59908096 (57 MB) npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface pcibios: BIOS version 2.00 sysctl machdep.i8254_freq=1189161 returns 0 Timecounter "ELAN" frequency 8333333 Hz quality 1000 pcib0: <AMD Elan SC520 host to PCI bridge> at pcibus 0 on motherboard pci0: <PCI bus> on pcib0 cbb0: <TI1410 PCI-CardBus Bridge> mem 0xa0000000-0xa0000fff irq 10 at device 9.0 on pci0 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 cbb0: [MPSAFE] sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xe100-0xe1ff mem 0xa0001000-0xa0001fff irq 11 at device 18.0 on pci0 sis0: Silicon Revision: DP83816A sis0: Ethernet address: 00:00:24:c2:8e:c0 miibus0: <MII bus> on sis0 ukphy0: <Generic IEEE 802.3u media interface> on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0xe200-0xe2ff mem 0xa0002000-0xa0002fff irq 5 at device 19.0 on pci0 sis1: Silicon Revision: DP83816A sis1: Ethernet address: 00:00:24:c2:8e:c1 miibus1: <MII bus> on sis1 ukphy1: <Generic IEEE 802.3u media interface> on miibus1 ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto isa0: <ISA bus> on motherboard orm0: <Option ROM> at iomem 0xc8000-0xd0fff on isa0 pmtimer0 on isa0 ata0 at port 0x3f6,0x1f0-0x1f7 irq 14 on isa0 ata0: [MPSAFE] ata1 at port 0x376,0x170-0x177 irq 15 on isa0 ata1: [MPSAFE] atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 psm0: unable to get the current command byte value. fdc0: ready for input in output fdc0: cmd 3 failed at out byte 1 of 3 ppc0: parallel port not found. sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A, console sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A Timecounters tick every 4.000 msec Elan-mmcr driver: MMCR at 0xc63d4000. pccard0: Allocation failed for cfe 15 pccard0: Allocation failed for cfe 23 cbb0: ready never happened, status = 4f sio4: <PCMCIA 56K V.90 Fax Modem (LK) > at port 0x3e8-0x3ef irq 10 function 0 config 31 on pccard0 sio4: type 16550A sio4: unable to activate interrupt in fast mode - using normal mode The system froze directly after . Any Idea . Christophe Boy IT Management Specialist Mail : <mailto:cboy_at_altea.ca> cboy_at_altea.ca Altea Communications 2231 rue Coursol H3J1C6 Montreal Quebec Canada The Network Expertise ( Network Management & Performance Tools LAN/WAN ) Tel : (514) 937-3381 Fax : (514) 937-3383 WWW : <http://www.altea.ca/> http://www.altea.ca/Received on Thu Aug 26 2004 - 18:59:12 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:08 UTC