Dlink Dwl 520 E1

I have two wireless device.
- Pcmcia Orinoco Wireless Silver 11mbps
- Dlink Dwl 520 revision v.E1

FreeBSD 5.2.1-R

Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.2.1-RC #0: Sat Mar 15 15:59:14 BRT 2003
    root_at_gibson.x86.net:/usr/src/sys/i386/compile/GIBSON
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0753000.
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium/P54C (166.40-MHz 586-class CPU)
  Origin = "GenuineIntel"  Id = 0x52c  Stepping = 12
  Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
real memory  = 67108864 (64 MB)
avail memory = 59830272 (57 MB)
Intel Pentium detected, installing workaround for F00F bug
npx0: [FAST]
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcibios: BIOS version 2.10
Using $PIR table, 6 entries at 0xc00fd9d0
pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci_cfgintr: 0:7 INTD BIOS irq 11
pci_cfgintr: 0:8 INTA BIOS irq 10
pci_cfgintr: 0:9 INTA BIOS irq 9
pci_cfgintr: 0:10 INTA BIOS irq 12
pci_cfgintr: 0:11 INTA BIOS irq 11
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX3 WDMA2 controller> port 0xf000-0xf00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata0: [MPSAFE]
ata1: at 0x170 irq 15 on atapci0
ata1: [MPSAFE]
pci0: <serial bus, USB> at device 7.2 (no driver attached)
pci0: <display, VGA> at device 8.0 (no driver attached)
cbb0: <RF5C475 PCI-CardBus Bridge> irq 9 at device 9.0 on pci0
wi0: <Intersil Prism2.5> mem 0xe0410000-0xe0410fff irq 12 at device 10.0 on pci0
wi0: timeout in wi_cmd 0x0000; event status 0x0000
wi0: wi_cmd: busy bit won't clear.
: init failed
device_probe_and_attach: wi0 attach returned 6
rl0: <RealTek 8139 10/100BaseTX> port 0x6100-0x61ff mem 0xe0411000-0xe04110ff irq 11 at device 11.0 on pci0
rl0: Ethernet address: 00:50:fc:5f:c8:80
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
ppi0: <Parallel I/O> on ppbus0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0700> can't assign resources (port)
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0501> can't assign resources (port)
Timecounter "TSC" frequency 166401647 Hz quality 800
Timecounters tick every 1.000 msec
ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to deny, logging limited to 100 packets/entry by default
IPsec: Initialized Security Association Processing.
wi0: <Lucent Technologies WaveLAN/IEEE> at port 0x100-0x13f irq 9 function 0 config 1 on pccard0
wi0: 802.11 address: 00:02:2d:1d:3c:85
wi0: using Lucent Technologies, WaveLAN/IEEE
wi0: Lucent Firmware: Station (8.72.1)
wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
GEOM: create disk ad0 dp=0xc13c8260
ad0: 4110MB <QUANTUM FIREBALL CR4.3A> [14848/9/63] at ata0-master WDMA2
Mounting root from ufs:/dev/ad0s2a

Pcmcia Orinoco Wireless work fine, but Dlink Dwl 520 not work.
Any idea ?

[]s Daniel Dias Gonálves
f22_at_netbsd.com.br