HI! I sent an email few days ago about ACPI and APM problems on my compaq presario 1800. I update the system,from 5.1-RELEASE to 5.2-RC2, downalod the sys with cvsup, recompile ONLY the kernel to : >uname -a FreeBSD 127.0.0.1 5.2-CURRENT FreeBSD 5.2-CURRENT #0: Wed Dec 31 15:04:17 GMT 2003 root_at_127.0.0.1:/usr/obj/usr/src/sys/MYKERNEL i386 (MYKERNEL is the GENERIC with device pcm, because adding snd_ess_load="YES" on loader.conf wasn't actually creating /dev/dsp.. but this is a different story :p) with 5.1-RELEASE, 5.2 RC2 and now 5.2 CURRENT, the problem is still the same, the ACPI doesn't show the life time of the battery. with the 5.2 CURRENT I have tried to enable the apm: >loader.conf: add apm_load="YES" #added >device.hints : hint.acpi.0.disabled=1 #added hint.apm.0.disabled=0 #modified >rc.conf apm_enabled="YES" #added apmd_enabled="YES" #added after the reboot, nothing didn't change, the apm was only saying that I had a battery and the total charge of it, but still nothing about the time, so I decide to put back the acpi, so I remmed out in device.hints the lines that I added, and delete the line on loader.conf, forgottin to delete the lines in the rc.conf after the reboot I saw the line in the dmesg that said that apm wasn't compiled with the kernel, I remmed out that lines, but before reboot I checked the battery status writing APM >apm APM version: 1.2 APM Management: Disabled AC Line status: off-line Battery status: high Remaining battery life: 83% Remaining battery time: 2:56:00 Number of batteries: 1 Battery 0: Battery status: high Remaining battery life: 83% Remaining battery time: 2:56:00 Resume timer: unknown [...] I can see the battery time... I start KDE and also KDE was working fine with it, reading the life and the time of the battery.... I rebooted with the lines in the rc.conf remmed out, I still get error on the boot from the ACPI (I'll copy the dmesg), but I still can see the life and time of the battery, except for KDE, that says that apm is not running... AND.. when I "put to sleep" the computer, the monitor doesn't go off, except if I close the lid. when I try to "wake up" the computer, sometime I get some errors after: ata0: resetting devices .. but everything works fine. I don't get the errors if I am in X (KDE) last thing: when I was running 5.1-RELEASE the acpi was putting down the use of the CPU in battery mode from 8 to 4, with 5.2 the cpu works always at 8: >sysctl -a hw.acpi (with acline =1) hw.acpi.supported_sleep_state: S1 S5 hw.acpi.power_button_state: S5 hw.acpi.sleep_button_state: S1 hw.acpi.lid_switch_state: S1 hw.acpi.standby_state: S1 hw.acpi.suspend_state: S3 hw.acpi.sleep_delay: 5 hw.acpi.s4bios: 1 hw.acpi.verbose: 0 hw.acpi.disable_on_poweroff: 1 hw.acpi.reset_video: 1 hw.acpi.cpu.throttle_max: 8 hw.acpi.cpu.throttle_state: 8 hw.acpi.cpu.cx_supported: C1/0 C2/10 hw.acpi.cpu.cx_lowest: 0 hw.acpi.cpu.cx_history: 767689/0 0/0 hw.acpi.thermal.min_runtime: 0 hw.acpi.thermal.polling_rate: 30 hw.acpi.thermal.tz0.temperature: 3252 hw.acpi.thermal.tz0.active: -1 hw.acpi.thermal.tz0.thermal_flags: 0 hw.acpi.thermal.tz0._PSV: 3632 hw.acpi.thermal.tz0._HOT: -1 hw.acpi.thermal.tz0._CRT: 3732 hw.acpi.thermal.tz0._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 hw.acpi.battery.life: 88 hw.acpi.battery.time: -1 hw.acpi.battery.state: 2 hw.acpi.battery.units: 1 hw.acpi.battery.info_expire: 5 hw.acpi.acline: 1 >sysctl -a ha.acpi (with the battery only) hw.acpi.supported_sleep_state: S1 S5 hw.acpi.power_button_state: S5 hw.acpi.sleep_button_state: S1 hw.acpi.lid_switch_state: S1 hw.acpi.standby_state: S1 hw.acpi.suspend_state: S3 hw.acpi.sleep_delay: 5 hw.acpi.s4bios: 1 hw.acpi.verbose: 0 hw.acpi.disable_on_poweroff: 1 hw.acpi.reset_video: 1 hw.acpi.cpu.throttle_max: 8 hw.acpi.cpu.throttle_state: 8 hw.acpi.cpu.cx_supported: C1/0 C2/10 hw.acpi.cpu.cx_lowest: 0 hw.acpi.cpu.cx_history: 772436/0 0/0 hw.acpi.thermal.min_runtime: 0 hw.acpi.thermal.polling_rate: 30 hw.acpi.thermal.tz0.temperature: 3252 hw.acpi.thermal.tz0.active: -1 hw.acpi.thermal.tz0.thermal_flags: 0 hw.acpi.thermal.tz0._PSV: 3632 hw.acpi.thermal.tz0._HOT: -1 hw.acpi.thermal.tz0._CRT: 3732 hw.acpi.thermal.tz0._ACx: -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 hw.acpi.battery.life: 88 hw.acpi.battery.time: 576 hw.acpi.battery.state: 1 hw.acpi.battery.units: 1 hw.acpi.battery.info_expire: 5 hw.acpi.acline: 0 >dmesg Copyright (c) 1992-2003 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2-CURRENT #0: Wed Dec 31 15:04:17 GMT 2003 root_at_127.0.0.1:/usr/obj/usr/src/sys/MYKERNEL Preloaded elf kernel "/boot/kernel/kernel" at 0xc0af4000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0af41f4. Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel Pentium III (796.54-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x686 Stepping = 6 Features=0x387f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,PN,MMX,FXSR,SSE> real memory = 134152192 (127 MB) avail memory = 121618432 (115 MB) Pentium Pro MTRR support enabled npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <PTLTD RSDT > on motherboard pcibios: BIOS version 2.10 Using $PIR table, 9 entries at 0xc00fdf30 ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST acpi0: Power Button (fixed) Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0 acpi_cpu0: <CPU> port 0x530-0x537 on acpi0 acpi_tz0: <Thermal Zone> port 0x530-0x537 on acpi0 acpi_button0: <Sleep Button> on acpi0 acpi_button1: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib0: slot 7 INTD is routed to irq 11 pcib0: slot 9 INTA is routed to irq 3 pcib0: slot 17 INTA is routed to irq 5 pcib0: slot 18 INTA is routed to irq 11 agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xf4000000-0xf7ffffff at device 0.0 on pci0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pcib1: slot 0 INTA is routed to irq 5 pci1: <display, VGA> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 UDMA33 controller> port 0x14a0-0x14af at device 7.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x1480-0x149f irq 11 at device 7.2 on pci0 usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) pci0: <simple comms> at device 9.0 (no driver attached) cbb0: <TI1410 PCI-CardBus Bridge> at device 10.0 on pci0 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 pcib0: slot 10 INTA is routed to irq 11 cbb0: [MPSAFE] pcm0: <ESS Solo-1 (unknown vendor)> port 0x14d8-0x14db,0x14dc-0x14df,0x14b0-0x14bf,0x14c0-0x14cf,0x1400-0x143f irq 5 at device 17.0 on pci0 fxp0: <Intel 82559 Pro/100 Ethernet> port 0x1440-0x147f mem 0xf0000000-0xf00fffff,0xf0100000-0xf0100fff irq 11 at device 18.0 on pci0 fxp0: Ethernet address 00:02:a5:14:aa:7a miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-1287: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST ACPI-0175: *** Error: Method execution failed [\\_SB_.BATT._STA] (Node 0xc1f52d00), AE_NOT_EXIST acpi_cmbat0: <Control Method Battery> on acpi0 acpi_acad0: <AC Adapter> on acpi0 acpi_lid0: <Control Method Lid Switch> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: model IntelliMouse, device ID 3 acpi_ec0: <Embedded Controller: GPE 0x9, GLK> port 0x66,0x62 on acpi0 fdc0: cannot reserve control I/O port range (control port) fdc0: cannot reserve control I/O port range (control port) orm0: <Option ROM> at iomem 0xc0000-0xcefff on isa0 pmtimer0 on isa0 fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/15 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 796541496 Hz quality 800 Timecounters tick every 10.000 msec acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% system power profile changed to 'economy' system power profile changed to 'performance' GEOM: create disk ad0 dp=0xc201d560 ad0: 19077MB <HITACHI_DK23BA-20> [38760/16/63] at ata0-master UDMA33 acd0: DVDROM <TOSHIBA DVD-ROM SD-C2502> at ata1-master PIO4 sorry for my english, Italian guy here. Thanks a lot Fabrizio ParrellaReceived on Thu Jan 01 2004 - 12:44:17 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:36 UTC