I'm also experiencing this problem since the last 2 days. Each day I updated my source and make world but the problem keeps on happening. I'm using Dell Optiplex GX260: - P4 1.8GHz - 256MB RAM I'm using SCHED_4BSD. My system usually hard hangs when the system is busily accessing my hard disks. I can't do anything except when pressing NumLock, the light will turn on/off but --- (oops, my comp hang just now. Luckily evolution saved this email message. --- The NumLock LED blinks when I press the NumLock key but not in the correct way. Sometimes the LED flicker but does not turned off while pressing NumLock key and sometimes it should turned on but it doesn't. I deleted the miibus and fxp entry in my kernel config file but I'm using a kernel which has both entries. I also kldload if_em module for my NIC. Thank you. On Sat, 2004-07-10 at 13:18, Robert Watson wrote: > On Fri, 9 Jul 2004, Robert Watson wrote: > > > I'm now experiencing extremely hard hangs in the following configurations: > > > > SMP kernel running SCHED_ULE with hyperthreads > > SMP kernel running SCHED_4BSD with hyperthreads > > > > To generate the load, I'm using the "supersmack" benchark with the > > select-key.smack query set with 30 client workers and 10,000 > > transactions. I am able to reliable hang the system with one or two > > runs. > > > > By disabling the "#define PREEMPTION" entry in param.h with SCHED_4BSD, > > I'm able to complete the benchmark several times in a row without > > apparent problems. However, I'll leave it running for a few more hours > > and see if I didn't just "get lucky". I'll then try SCHED_ULE w/o > > PREEMPTION. > > > > By "extremely hard" I mean that I am unable to break into the debugger > > using a serial break on the serial console. I have not yet been able to > > run the test on a system with easily accessible NMI but will attempt to > > do so in the next few days. > > > > I'll give UP a spin with various combinations next. > > FYI, UP+SCHED_ULE with PREEMPTION hung within three seconds of starting > the benchmark. Without PREEMPTION it seems to run fine. > > So it looks like either PREEMPTION has a problem, or it's triggering an > existing problem elsewhere. If it's only one problem, it seems not to > depend on either SMP/UP or the scheduler choice. If it's multiple > problems, who knows :-). As the MySQL test relies on threading, we could > be looking at an edge case involving threading and scheduling/preemption > -- the other reports I've seen mention X11/KDE, which would also involve > threading. On the other hand, it could just be load. Tomorrow I'll load > up a box with non-threaded apps and see what happens. > > Robert N M Watson FreeBSD Core Team, TrustedBSD Projects > robert_at_fledge.watson.org Principal Research Scientist, McAfee Research > > > _______________________________________________ > freebsd-current_at_freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org" -- Nawfal bin Mohmad Rouyan <nawfal_at_mmu.edu.my> Multimedia University Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.2-CURRENT #1: Sat Jul 10 05:05:58 MYT 2004 root_at_:/usr/obj/usr/src/sys/OPAL Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 1.80GHz (1800.03-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf27 Stepping = 7 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> real memory = 267849728 (255 MB) avail memory = 252440576 (240 MB) npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <DELL GX260 > on motherboard acpi0: [GIANT-LOCKED] acpi0: Power Button (fixed) Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> port 0x530-0x537 on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 agp0: <Intel 82845G host to AGP bridge> mem 0xe8000000-0xefffffff at device 0.0 on pci0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 drm0: <ATI Radeon QW RV200 7500> port 0xec00-0xecff mem 0xff8f0000-0xff8fffff,0xf0000000-0xf7ffffff irq 11 at device 0.0 on pci1 info: [drm] AGP at 0xe8000000 128MB info: [drm] Initialized radeon 1.11.0 20020828 on minor 0 uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xff80-0xff9f irq 11 at device 29.0 on pci0 uhci0: [GIANT-LOCKED] usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xff60-0xff7f irq 10 at device 29.1 on pci0 uhci1: [GIANT-LOCKED] usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xff40-0xff5f irq 9 at device 29.2 on pci0 uhci2: [GIANT-LOCKED] usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered pci0: <serial bus, USB> at device 29.7 (no driver attached) pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci2: <ACPI PCI bus> on pcib2 pcm0: <Creative EMU10K1> port 0xdce0-0xdcff irq 11 at device 7.0 on pci2 pcm0: <SigmaTel STAC9721/23 AC97 Codec> em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.25> port 0xdc80-0xdcbf mem 0xff6e0000-0xff6fffff irq 9 at device 12.0 on pci2 em0: [GIANT-LOCKED] em0: Ethernet address: 00:08:74:cc:ad:ed em0: Speed:N/A Duplex:N/A isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH4 UDMA100 controller> port 0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0 ata0: at 0x1f0 irq 14 on atapci0 ata1: at 0x170 irq 15 on atapci0 ichsmb0: <Intel 82801DC (ICH4) SMBus controller> port 0xcc80-0xcc9f irq 11 at device 31.3 on pci0 ichsmb0: [GIANT-LOCKED] smbus0: <System Management Bus> on ichsmb0 smb0: <SMBus generic I/O> on smbus0 fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model IntelliMouse, device ID 3 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A ppc0 port 0x778-0x77f,0x378-0x37f irq 7 on acpi0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 orm0: <ISA Option ROM> at iomem 0xc0000-0xcbfff on isa0 pmtimer0 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 1800034424 Hz quality 800 Timecounters tick every 1.000 msec ad0: 38146MB <WDC WD400BB-75DEA0> [77504/16/63] at ata0-master UDMA100 ad1: 238475MB <WDC WD2500JB-00EVA0> [484521/16/63] at ata0-slave UDMA100 acd0: CDROM <SAMSUNG CD-ROM SC-148C> at ata1-master UDMA33 cd0 at ata1 bus 0 target 0 lun 0 cd0: <SAMSUNG CD-ROM SC-148C B105> Removable CD-ROM SCSI-0 device cd0: 33.000MB/s transfers cd0: Attempt to query device size failed: NOT READY, Medium not present Mounting root from ufs:/dev/ad0s1a WARNING: / was not properly dismounted WARNING: /home was not properly dismounted /home: mount pending error: blocks 12 files 2 /home: superblock summary recomputed em0: Link is up 100 Mbps Full Duplex # # GENERIC -- Generic kernel configuration file for FreeBSD/i386 # # For more information on this file, please read the handbook section on # Kernel Configuration Files: # # http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html # # The handbook is also available locally in /usr/share/doc/handbook # if you've installed the doc distribution, otherwise always see the # FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the # latest information. # # An exhaustive list of options and more detailed explanations of the # device lines is also present in the ../../conf/NOTES and NOTES files. # If you are in doubt as to the purpose or necessity of a line, check first # in NOTES. # # $FreeBSD: src/sys/i386/conf/GENERIC,v 1.394 2003/12/03 21:13:06 jhb Exp $ machine i386 cpu I686_CPU ident OPAL options DDB options DDB_TRACE makeoptions DEBUG=-g options SCHED_4BSD options INET #InterNETworking options FFS #Berkeley Fast Filesystem options SOFTUPDATES #Enable FFS soft updates support options UFS_ACL #Support for access control lists options UFS_DIRHASH #Improve performance on big directories options NFSCLIENT #Network Filesystem Client options NFSSERVER #Network Filesystem Server options MSDOSFS #MSDOS Filesystem options CD9660 #ISO 9660 Filesystem options PROCFS #Process filesystem (requires PSEUDOFS) options PSEUDOFS #Pseudo-filesystem framework options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!] options COMPAT_FREEBSD4 #Compatible with FreeBSD4 options KTRACE #ktrace(1) support options SYSVSHM #SYSV-style shared memory options SYSVMSG #SYSV-style message queues options SYSVSEM #SYSV-style semaphores options _KPOSIX_PRIORITY_SCHEDULING #Posix P1003_1B real-time extensions options KBD_INSTALL_CDEV # install a CDEV entry in /dev options AHC_REG_PRETTY_PRINT # Print register bitfields in debug # output. Adds ~128k to driver. options AHD_REG_PRETTY_PRINT # Print register bitfields in debug # output. Adds ~215k to driver. options CPU_ENABLE_SSE options CPU_FASTER_5X86_FPU options DEVICE_POLLING options HZ=1000 device isa device pci # Floppy drives device fdc # ATA and ATAPI devices device ata device atadisk # ATA disk drives device atapicd # ATAPI CDROM drives options ATA_STATIC_ID #Static device numbering # atkbdc0 controls both the keyboard and the PS/2 mouse device atkbdc # AT keyboard controller device atkbd # AT keyboard device psm # PS/2 mouse device vga # VGA video card driver device splash # Splash screen and screen saver support # syscons is the default console driver, resembling an SCO console device sc # Enable this for the pcvt (VT220 compatible) console driver #device vt #options XSERVER # support for X server on a vt console #options FAT_CURSOR # start with block cursor device agp # support several AGP chipsets # Floating point support - do not disable. device npx # Power management support (see NOTES for more options) #device apm # Add suspend/resume support for the i8254. device pmtimer # Serial (COM) ports device sio # 8250, 16[45]50 based serial ports # Parallel port device ppc device ppbus # Parallel port bus (required) device lpt # Printer device plip # TCP/IP over parallel device ppi # Parallel port interface device #device vpo # Requires scbus and da # If you've got a "dumb" serial or parallel PCI card that is # supported by the puc(4) glue driver, uncomment the following # line to enable it (connects to the sio and/or ppc drivers): #device puc # Pseudo devices - the number indicates how many units to allocate. device random # Entropy device device loop # Network loopback device ether # Ethernet support device pty # Pseudo-ttys (telnet etc) # The `bpf' device enables the Berkeley Packet Filter. # Be aware of the administrative consequences of enabling this! device bpf # Berkeley packet filter device scbus device cd device pass device da device atapicam device pcm device smbus device ichsmb device smb device uhci device ohci device usb device ums device umass options PFIL_HOOKS device pf device pflog device pfsync options ZERO_COPY_SOCKETS options ALTQ options ALTQ_CBQ # Class Bases Queueing options ALTQ_RED # Random Early Drop options ALTQ_RIO # RED In/Out options ALTQ_HFSC # Hierarchical Packet Scheduler options ALTQ_CDNR # Traffic conditioner options ALTQ_PRIQ # Prioirity Queueing options ALTQ_NOPCC options RANDOM_IP_ID options IPSTEALTH options CONSPEED=115200Received on Sat Jul 10 2004 - 04:27:41 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:01 UTC