Re: ACPI Error: AE_NO_HARDWARE_RESPONSE

From: Nate Lawson <nate_at_root.org>
Date: Fri, 4 Jun 2004 21:30:08 -0700 (PDT)
This is harmless but you can help solve it by recompiling your acpi
module:

cd /sys/modules/acpi/acpi && make ACPI_DEBUG=1 && cp acpi.ko /

Then enable debugging prints by adding this to /boot/loader.conf:

debug.acpi.layer="ACPI_POWER"
debug.acpi.level="ACPI_LV_OBJECTS ACPI_LV_ALL_EXCEPTIONS"

Then reboot, load /acpi.ko at the loader prompt, and send me your full
dmesg, including all debug prints and errors.

Thanks,
Nate

On Sat, 5 Jun 2004 j.e.drews_at_att.net wrote:
> FreeBSD 5.2-CURRENT #0: Tue Jun  1 00:00:38 CDT 2004
>
> Nate:
>
>  I managed to get these errors on bootup tonight:
>
> Jun  4 22:28:07 notebook login: ROOT LOGIN (root) ON ttyv1
> pci0: Failed to set ACPI power state D3 on (null): AE_BAD_PARAMETER
> pci0: Failed to set ACPI power state D3 on (null): AE_BAD_PARAMETER
>
>                           Kind regards,
>                           Jonathan
>
>
> > Hi Nate:
> >
> >  I made the polling adjustment that you suggested:
> > sysctl hw.acpi.thermal.polling_rate=1
> >
> > and then ran the script while compiling qt33 and Mozilla at the same time. the
> > initial reading was at:  hw.acpi.thermal.tz0.temperature: 3112
> > the high temps were:
> > hw.acpi.thermal.tz0.temperature: 3242
> > hw.acpi.thermal.tz0.temperature: 3252
> >
> > the fan kicked on at 3232. I could not get the error again, even though I ran
> > the computer under load for quite a while.
> >
> > The output of acpidump -t -d > pwrnotebooks-C.asl is here:
> >
> > http://www.silbsd.org/bugreports/pwrnotebooks-C.asl
> >
> > it was too many lines to post to the list. Let me try a few more things with to
> > tease out this error  message again.
> >
> >                                Kind regards
> >                                Jonathan
> >
> >
> >
> >
> >
> >
> > > This means the EC timed out while reading the current temp.  I'm not sure
> > > what is causing this.  Try setting:
> > >
> > > sysctl hw.acpi.thermal.polling_rate=1
> > >
> > > This makes the thermal poll run every second.  And then run this script:
> > >
> > > #!/bin/sh
> > > while [ 1 ]; do
> > > 	sysctl hw.acpi.thermal.tz0.temperature
> > > 	sleep .1
> > > done
> > >
> > > This polls the temp over and over to see if it can reproduce the error.
> > > Don't worry, this error only means your temp reading will be incorrect (no
> > > system damage will occur).  Let me know how often the errors appear.  Try
> > > loading the system with some other apps if the errors don't appear.
> > >
> > > Also, send me the output of so I can see your notebook's config:
> > >     acpidump -t -d > pwrnotebooks-C.asl
> > >
> > > -Nate
> > > _______________________________________________
> > > freebsd-current_at_freebsd.org mailing list
> > > http://lists.freebsd.org/mailman/listinfo/freebsd-current
> > > To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"
> > _______________________________________________
> > freebsd-current_at_freebsd.org mailing list
> > http://lists.freebsd.org/mailman/listinfo/freebsd-current
> > To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"
>
Received on Fri Jun 04 2004 - 19:30:06 UTC

This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:56 UTC