Re: hang after after update: "adX: FAILURE - already active DMA on this device" (ICH5 system)

On Sun, 6 Jun 2004 12:32:24 +0200
Alexander Leidinger <Alexander_at_Leidinger.net> wrote:

> Hi,
> 
> after updating from a ~May 15 kernel to yesterdays kernel the system
> hangs while probing:
> ---snip---
> ata3: reset tp1 mask=03 ostat0=d0 ostat1=00
> ad3: stat=0x50 err=0x01 lsb=0x00 msb=0x00
> ata3-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
> ata3: reset tp2 mask=03 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
> ata3: resetting done ..
> ad3: pio=0x0c wdma=0x22 udma=0x46 cable=40pin
> ad3: FAILURE - SETFEATURES SET TRANSFER MODE
> status=51<READY,DSC,ERROR> error=4<ABORTED> ata3: device config done
> .. ad3: FAILURE - READ_DMA status=51<READY,DSC,ERROR> error=0 dma=0x06
> LBA=0 ad2: FAILURE - already active DMA on this device
> ad2: setting up DMA failed
> ad2: TIMEOUT - READ_DMA retrying (2 retries left) LBA=63
> ata2: reiniting channel ..
> ata2: reset tp1 mask=03 ostat0=d0 ostat1=00
> ad2: stat=0x50 err=0x01 lsb=0x00 msb=0x00
> ata2-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00
> ata2: reset tp2 mask=0x stat0=50 stat1=00 devices=0x1<ATAMASTER>
> ata2: resetting done ..
> ad2: pio=0x0c wdma=0x22 udma=0x46 cable=40pin
> ata2: device config done ..
> ad2: FAILURE - already active DMA on this device
> ad2: setting up DMA failed
> ad2: TIMEOUT - READ_DMA retrying (2 retries left) LBA=191
> ---snip---
> 
> This is an ICH5 system:
> ---snip---
> atapci0: <Intel ICH5 UDMA100 controller> port
> 0xf000-0xf00f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on
> pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xf000
> atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
> atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
> ata0: at 0x1f0 irq 14 on atapci0
> atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
> atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
> ata1: at 0x170 irq 15 on atapci0
> atapci1: <Intel ICH5 SATA150 controller> port
> 0xd000-0xd00f,0xcc00-0xcc03,0xc800-0xc807,0xc400-0xc403,0xc000-0xc007
> irq 18 at device 31.2 on pci0 atapci1: Reserved 0x10 bytes for rid
> 0x20 type 4 at 0xd000 atapci1: Reserved 0x8 bytes for rid 0x10 type 4
> at 0xc000 atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0xc400
> ata2: at 0xc000 on atapci1
> atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0xc800
> atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0xcc00
> ata3: at 0xc800 on atapci1
> 
> ad0: 78167MB <Maxtor 6Y080L0> [158816/16/63] at ata0-master UDMA100
> ata1-master: DMA limited to UDMA33, non-ATA66 cable or device
> ad1: 19547MB <FUJITSU MPE3204AT> [39714/16/63] at ata1-master UDMA33
> acd0: DVDROM <JLMS XJ-HD165H> at ata1-slave PIO4
> ad2: 78167MB <Maxtor 6Y080M0> [158816/16/63] at ata2-master SATA150
> ad3: 78167MB <Maxtor 6Y080M0> [158816/16/63] at ata3-master SATA150
> ---snip---
> 
> The CPU is with HT, but SMP is disabled in the loader.
> 
> Any ideas?
> 
> Bye,
> Alexander.
> 
> -- 
>            I'm available to get hired (preferred in .lu).
> 

I have these problems too. Look here

http://docs.freebsd.org/cgi/mid.cgi?20040604144627.CFD7A613D

I havn't got any response from the developers. Maybe Soren Schmidt have
experienced the same thing on his system? He purchased a P4 HTT ICH5
system a while ago I think. ;)