> -----Original Message----- > From: John Baldwin [mailto:jhb_at_FreeBSD.org] > Sent: Monday, May 24, 2004 1:10 PM > To: freebsd-current_at_FreeBSD.org > Cc: Robin P. Blanchard; current_at_FreeBSD.org > Subject: Re: Latest kernel hanging on amr (del 1550) > > On Sunday 23 May 2004 01:47 pm, Robin P. Blanchard wrote: > > Latest kernel hangs after "waiting for SCSI devices to > settle" on my > > dell 1550. Seeing as how the amr driver hasn't changed in > some time, > > must be somewhere else. Maybe the geom_disk ? Anyone else > seeing this > > ? This is a smp box, so that may be an option also. > > It could be an interrupt issue. Try setting > 'hint.apic.0.disabled=1' from the loader to see if the > problem goes away. If so, pleas send me a boot -v dmesg. Grabbed a new CVS snapshot and kernel still hangs at same place. Setting hint.apic.0.disabled=1 didn't help, neither did hint.acpi.0.disabled=1. Setting both induced a kernel panic. Here's a verbose boot from the older, working kernel: MP Configuration Table version 1.4 found at 0xc00f0000 APIC: Using the MPTable enumerator. SMP: Added CPU 1 (BSP) SMP: Added CPU 0 (AP) MPTable: <DELL POWEREDGE DF> APIC ID: physical 0, logical 0:0 APIC ID: physical 1, logical 0:1 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 1 cpu1 (AP): APIC ID: 0 bios32: Found BIOS32 Service Directory header at 0xc00ffe80 bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0xcb7e pnpbios: Found PnP BIOS data at 0xc00fe2d0 pnpbios: Entry = f0000:e2f4 Rev = 1.0 Other BIOS signatures found: ioapic0: Changing APIC ID to 2 ioapic0: Assuming intbase of 0 ioapic0: intpin 0 -> ExtINT (edge, activehi) ioapic0: intpin 1 -> irq 1 (edge, activehi) ioapic0: intpin 2 -> irq 2 (edge, activehi) ioapic0: intpin 3 -> irq 3 (edge, activehi) ioapic0: intpin 4 -> irq 4 (edge, activehi) ioapic0: intpin 5 -> irq 5 (edge, activehi) ioapic0: intpin 6 -> irq 6 (edge, activehi) ioapic0: intpin 7 -> irq 7 (edge, activehi) ioapic0: intpin 8 -> irq 8 (edge, activehi) ioapic0: intpin 9 -> irq 9 (edge, activehi) ioapic0: intpin 10 -> irq 10 (edge, activehi) ioapic0: intpin 11 -> irq 11 (edge, activehi) ioapic0: intpin 12 -> irq 12 (edge, activehi) ioapic0: intpin 13 -> irq 13 (edge, activehi) ioapic0: intpin 14 -> irq 14 (edge, activehi) ioapic0: intpin 15 -> irq 15 (edge, activehi) ioapic1: Changing APIC ID to 3 ioapic1: Assuming intbase of 16 ioapic1: intpin 0 -> irq 16 (level, activelo) ioapic1: intpin 1 -> irq 17 (level, activelo) ioapic1: intpin 2 -> irq 18 (level, activelo) ioapic1: intpin 3 -> irq 19 (level, activelo) ioapic1: intpin 4 -> irq 20 (level, activelo) ioapic1: intpin 5 -> irq 21 (level, activelo) ioapic1: intpin 6 -> irq 22 (level, activelo) ioapic1: intpin 7 -> irq 23 (level, activelo) ioapic1: intpin 8 -> irq 24 (level, activelo) ioapic1: intpin 9 -> irq 25 (level, activelo) ioapic1: intpin 10 -> irq 26 (level, activelo) ioapic1: intpin 11 -> irq 27 (level, activelo) ioapic1: intpin 12 -> irq 28 (level, activelo) ioapic1: intpin 13 -> irq 29 (level, activelo) ioapic1: intpin 14 -> irq 30 (level, activelo) ioapic1: intpin 15 -> irq 31 (level, activelo) ioapic0: intpin 1 trigger: edge ioapic0: intpin 1 polarity: high ioapic0: intpin 4 trigger: edge ioapic0: intpin 4 polarity: high ioapic0: intpin 6 trigger: edge ioapic0: intpin 6 polarity: high ioapic0: intpin 7 trigger: level ioapic0: intpin 7 polarity: low ioapic0: intpin 8 trigger: edge ioapic0: intpin 8 polarity: high ioapic0: intpin 9 trigger: edge ioapic0: intpin 9 polarity: high ioapic0: intpin 12 trigger: edge ioapic0: intpin 12 polarity: high ioapic0: intpin 14 trigger: edge ioapic0: intpin 14 polarity: high ioapic0: intpin 15 trigger: edge ioapic0: intpin 15 polarity: high ioapic1: intpin 0 trigger: level ioapic1: intpin 0 polarity: low ioapic1: intpin 1 trigger: level ioapic1: intpin 1 polarity: low ioapic1: intpin 9 trigger: level ioapic1: intpin 9 polarity: low ioapic1: intpin 9 trigger: level ioapic1: intpin 9 polarity: low ioapic1: intpin 9 trigger: level ioapic1: intpin 9 polarity: low ioapic1: intpin 10 trigger: level ioapic1: intpin 10 polarity: low ioapic1: intpin 10 trigger: level ioapic1: intpin 10 polarity: low ioapic1: intpin 10 trigger: level ioapic1: intpin 10 polarity: low ioapic1: intpin 11 trigger: level ioapic1: intpin 11 polarity: low ioapic1: intpin 12 trigger: level ioapic1: intpin 12 polarity: low ioapic1: intpin 13 trigger: level ioapic1: intpin 13 polarity: low ioapic1: intpin 13 trigger: level ioapic1: intpin 13 polarity: low ioapic1: intpin 14 trigger: level ioapic1: intpin 14 polarity: low ioapic1: intpin 14 trigger: level ioapic1: intpin 14 polarity: low lapic: Routing ExtINT -> LINT0 lapic: LINT0 trigger: edge lapic: LINT0 polarity: active-high lapic: Routing NMI -> LINT1 lapic: LINT1 trigger: edge lapic: LINT1 polarity: active-high ioapic0 <Version 1.1> irqs 0-15 on motherboard ioapic1 <Version 1.1> irqs 16-31 on motherboard cpu0 BSP: ID: 0x01000000 VER: 0x00040011 LDR: 0x02000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff mem: <memory & I/O> Pentium Pro MTRR support enabled random: <entropy source, Software, Yarrow> null: <null device, zero device> npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface pci_open(1): mode 1 addr port (0x0cf8) is 0x80000270 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=80] is there (id=00081166) pcibios: BIOS version 2.10 Found $PIR table, 6 entries at 0xc00fc730 PCI-Only Interrupts: none Location Bus Device Pin Link IRQs embedded 4 5 A 0x6b 3 4 5 6 7 10 11 14 embedded 4 5 B 0x6c 3 4 5 6 7 10 11 14 slot 1 1 4 A 0x69 3 4 5 6 7 10 11 14 slot 1 1 4 B 0x6a 3 4 5 6 7 10 11 14 slot 1 1 4 C 0x69 3 4 5 6 7 10 11 14 slot 1 1 4 D 0x6a 3 4 5 6 7 10 11 14 embedded 0 1 A 0x60 3 4 5 6 7 10 11 14 embedded 0 2 A 0x61 3 4 5 6 7 10 11 14 embedded 0 15 A 0x6f 3 4 5 6 7 10 11 14 slot 2 4 6 A 0x6d 3 4 5 6 7 10 11 14 slot 2 4 6 B 0x6e 3 4 5 6 7 10 11 14 slot 2 4 6 C 0x6d 3 4 5 6 7 10 11 14 slot 2 4 6 D 0x6e 3 4 5 6 7 10 11 14 pcib1: <MPTable Host-PCI bridge> at pcibus 1 on motherboard pci1: <PCI bus> on pcib1 pci1: physical bus=1 found-> vendor=0x1011, dev=0x0026, revid=0x05 bus=1, slot=4, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns) pcib2: <MPTable PCI-PCI bridge> at device 4.0 on pci1 pcib2: secondary bus 2 pcib2: subordinate bus 3 pcib2: I/O decode 0xd000-0xdfff pcib2: memory decode 0xfe900000-0xfebfffff pcib2: prefetched decode 0xf8000000-0xfbffffff pci2: <PCI bus> on pcib2 pci2: physical bus=2 found-> vendor=0x1011, dev=0x0026, revid=0x05 bus=2, slot=0, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns) map[10]: type 4, range 32, base 0000dc00, size 8, enabled pcib2: device (null) requested decoded I/O range 0xdc00-0xdcff map[14]: type 1, range 32, base fe9ff000, size 12, enabled pcib2: device (null) requested decoded memory range 0xfe9ff000-0xfe9fffff pcib2: slot 1 INTA routed to irq 26 found-> vendor=0x1077, dev=0x1216, revid=0x06 bus=2, slot=1, func=0 class=01-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0117, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns) intpin=a, irq=26 powerspec 1 supports D0 D3 current D0 pcib3: <MPTable PCI-PCI bridge> at device 0.0 on pci2 pcib3: secondary bus 3 pcib3: subordinate bus 3 pcib3: I/O decode 0xf000-0xfff pcib3: memory decode 0xfeb00000-0xfebfffff pcib3: prefetched decode 0xf8000000-0xfbffffff pci3: <PCI bus> on pcib3 pci3: physical bus=3 map[10]: type 3, range 32, base f8000000, size 26, enabled pcib3: device (null) requested decoded memory range 0xf8000000-0xfbffffff pcib2: device (null) requested decoded memory range 0xf8000000-0xfbffffff pcib3: slot 0 INTA routed to irq 25 found-> vendor=0x101e, dev=0x1960, revid=0x20 bus=3, slot=0, func=0 class=01-04-00, hdrtype=0x00, mfdev=0 cmdreg=0x0116, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=25 powerspec 2 supports D0 D3 current D0 amr0: <LSILogic MegaRAID> mem 0xf8000000-0xfbffffff irq 25 at device 0.0 on pci3 amr0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xf8000000 amr0: [GIANT-LOCKED] amr0: <LSILogic PERC 3/DC> Firmware 196T, BIOS 3.33, 64MB RAM pci2: <mass storage, SCSI> at device 1.0 (no driver attached) pcib0: <MPTable Host-PCI bridge> at pcibus 0 on motherboard pci0: <PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x1166, dev=0x0008, revid=0x23 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1166, dev=0x0008, revid=0x01 bus=0, slot=0, func=1 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0147, statreg=0x2200, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1166, dev=0x0006, revid=0x01 bus=0, slot=0, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0142, statreg=0x2200, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1166, dev=0x0006, revid=0x01 bus=0, slot=0, func=3 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0142, statreg=0x2200, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 1, range 32, base fe2ff000, size 12, enabled map[14]: type 4, range 32, base 0000ecc0, size 6, enabled map[18]: type 1, range 32, base fe100000, size 20, enabled pcib0: slot 1 INTA routed to irq 16 found-> vendor=0x8086, dev=0x1229, revid=0x08 bus=0, slot=1, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns) intpin=a, irq=16 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base fe2fe000, size 12, enabled map[14]: type 4, range 32, base 0000ec80, size 6, enabled map[18]: type 1, range 32, base fe000000, size 20, enabled pcib0: slot 2 INTA routed to irq 17 found-> vendor=0x8086, dev=0x1229, revid=0x08 bus=0, slot=2, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns) intpin=a, irq=17 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base fd000000, size 24, enabled map[14]: type 4, range 32, base 0000e800, size 8, enabled map[18]: type 1, range 32, base fe2fd000, size 12, enabled found-> vendor=0x1002, dev=0x4752, revid=0x27 bus=0, slot=3, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x00a7, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D1 D2 D3 current D0 map[90]: type 4, range 32, base 00000580, size 4, enabled found-> vendor=0x1166, dev=0x0200, revid=0x50 bus=0, slot=15, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 000008b0, size 4, enabled found-> vendor=0x1166, dev=0x0211, revid=0x00 bus=0, slot=15, func=1 class=01-01-8a, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 1, range 32, base fe2fc000, size 12, enabled pcib0: unable to route slot 15 INTA found-> vendor=0x1166, dev=0x0220, revid=0x04 bus=0, slot=15, func=2 class=0c-03-10, hdrtype=0x00, mfdev=1 cmdreg=0x0117, statreg=0x0280, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns) intpin=a, irq=7 fxp0: <Intel 82559 Pro/100 Ethernet> port 0xecc0-0xecff mem 0xfe100000-0xfe1fffff,0xfe2ff000-0xfe2fffff irq 16 at device 1.0 on pci0 fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe2ff000 fxp0: using memory space register mapping fxp0: PCI IDs: 8086 1229 1028 00da 0008 fxp0: Dynamic Standby mode is disabled miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: bpf attached fxp0: Ethernet address: 00:b0:d0:f0:81:21 fxp0: [GIANT-LOCKED] fxp1: <Intel 82559 Pro/100 Ethernet> port 0xec80-0xecbf mem 0xfe000000-0xfe0fffff,0xfe2fe000-0xfe2fefff irq 17 at device 2.0 on pci0 fxp1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfe2fe000 fxp1: using memory space register mapping fxp1: PCI IDs: 8086 1229 1028 00da 0008 fxp1: Dynamic Standby mode is disabled miibus1: <MII bus> on fxp1 inphy1: <i82555 10/100 media interface> on miibus1 inphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp1: bpf attached fxp1: Ethernet address: 00:b0:d0:f0:81:22 fxp1: [GIANT-LOCKED] pci0: <display, VGA> at device 3.0 (no driver attached) isab0: <PCI-ISA bridge> port 0x580-0x58f at device 15.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <ServerWorks ROSB4 UDMA33 controller> port 0x8b0-0x8bf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 15.1 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x8b0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb ata0-slave: stat=0x00 err=0x00 lsb=0x00 msb=0xdf ata0: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> ata0: at 0x1f0 irq 14 on atapci0 ata0: [MPSAFE] atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=00 ostat0=ff ostat1=ff ata1: at 0x170 irq 15 on atapci0 ata1: [MPSAFE] pci0: <serial bus, USB> at device 15.2 (no driver attached) pcib4: <MPTable Host-PCI bridge> at pcibus 4 on motherboard pci4: <PCI bus> on pcib4 pci4: physical bus=4 map[10]: type 4, range 32, base 0000cc00, size 8, enabled map[14]: type 1, range 64, base fe6ff000, size 12, enabled pcib4: slot 5 INTA routed to irq 27 found-> vendor=0x9005, dev=0x00cf, revid=0x01 bus=4, slot=5, func=0 class=01-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0117, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns) intpin=a, irq=27 powerspec 2 supports D0 D3 current D0 map[10]: type 4, range 32, base 0000c800, size 8, enabled map[14]: type 1, range 64, base fe6fe000, size 12, enabled pcib4: slot 5 INTB routed to irq 28 found-> vendor=0x9005, dev=0x00cf, revid=0x01 bus=4, slot=5, func=1 class=01-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0117, statreg=0x02b0, cachelnsz=8 (dwords) lattimer=0x20 (960 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns) intpin=b, irq=28 powerspec 2 supports D0 D3 current D0 ahc0: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xcc00-0xccff mem 0xfe6ff000-0xfe6fffff irq 27 at device 5.0 on pci4 ahc0: Defaulting to MEMIO off ahc0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xcc00 ahc0: Reading SEEPROM...done. ahc0: Manual LVD Termination ahc0: BIOS eeprom is present ahc0: Secondary High byte termination Enabled ahc0: Secondary Low byte termination Enabled ahc0: Primary Low Byte termination Enabled ahc0: Primary High Byte termination Enabled ahc0: Downloading Sequencer Program... 423 instructions downloaded ahc0: Features 0x1fef6, Bugs 0x40, Flags 0x28485560 ahc0: [GIANT-LOCKED] aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs ahc1: <Adaptec aic7899 Ultra160 SCSI adapter> port 0xc800-0xc8ff mem 0xfe6fe000-0xfe6fefff irq 28 at device 5.1 on pci4 ahc1: Defaulting to MEMIO off ahc1: Reserved 0x100 bytes for rid 0x10 type 4 at 0xc800 ahc1: Reading SEEPROM...done. ahc1: Manual LVD Termination ahc1: BIOS eeprom is present ahc1: Secondary High byte termination Enabled ahc1: Secondary Low byte termination Enabled ahc1: Primary Low Byte termination Enabled ahc1: Primary High Byte termination Enabled ahc1: Downloading Sequencer Program... 423 instructions downloaded ahc1: Features 0x1fef6, Bugs 0x40, Flags 0x28485560 ahc1: [GIANT-LOCKED] aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs cpu0 on motherboard cpu1 on motherboard ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it pnpbios: 15 devices, largest 118 bytes PNP0c02: adding fixed memory32 range 0-0x9ffff, size=0xa0000 PNP0c02: adding fixed memory32 range 0x100000-0x7fffffff, size=0x7ff00000 PNP0c02: adding fixed memory32 range 0xff000000-0xffffffff, size=0x1000000 PNP0c02: adding fixed memory32 range 0xf0000-0xfffff, size=0x10000 PNP0c02: adding fixed memory32 range 0xec000-0xeffff, size=0x4000 PNP0c02: adding io range 0x800-0x88f, size=0x90, align=0x1 PNP0c02: adding io range 0x580-0x58f, size=0x10, align=0x1 PNP0c02: adding io range 0x62-0x63, size=0x2, align=0x1 PNP0c02: adding io range 0x65-0x6f, size=0xb, align=0x1 PNP0c02: adding io range 0xe0-0xef, size=0x10, align=0x1 pnpbios: handle 0 device ID PNP0c02 (020cd041) PNP0501: adding irq mask 0x10 PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0x8 pnpbios: handle 1 device ID PNP0501 (0105d041) PNP0700: adding irq mask 0x40 PNP0700: adding io range 0x3f0-0x3f5, size=0x6, align=0x8 PNP0700: adding dma mask 0x4 pnpbios: handle 2 device ID PNP0700 (0007d041) PNP0f13: adding irq mask 0x1000 pnpbios: handle 3 device ID PNP0f13 (130fd041) PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0x1 pnpbios: handle 4 device ID PNP0a03 (030ad041) PNP0c02: adding irq mask 0x200 pnpbios: handle 5 device ID PNP0c02 (020cd041) PNP0100: adding irq mask 0x1 PNP0100: adding io range 0x40-0x5f, size=0x20, align=0x1 pnpbios: handle 8 device ID PNP0100 (0001d041) PNP0200: adding io range 0x80-0x9f, size=0x20, align=0x1 PNP0200: adding io range 0-0x1f, size=0x20, align=0x1 PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0x1 PNP0200: adding dma mask 0x10 pnpbios: handle 9 device ID PNP0200 (0002d041) PNP0303: adding irq mask 0x2 PNP0303: adding io range 0x60-0x60, size=0x1, align=0x1 PNP0303: adding io range 0x64-0x64, size=0x1, align=0x1 pnpbios: handle 10 device ID PNP0303 (0303d041) PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1 pnpbios: handle 11 device ID PNP0800 (0008d041) PNP0b00: adding irq mask 0x100 PNP0b00: adding io range 0x70-0x7f, size=0x10, align=0x1 pnpbios: handle 12 device ID PNP0b00 (000bd041) PNP0c04: adding irq mask 0x2000 PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0x1 pnpbios: handle 13 device ID PNP0c04 (040cd041) PNP0c01: adding io range 0xc00-0xc01, size=0x2, align=0x1 PNP0c01: adding io range 0xc06-0xc08, size=0x3, align=0x1 PNP0c01: adding io range 0xc14-0xc14, size=0x1, align=0x1 PNP0c01: adding io range 0xc50-0xc52, size=0x3, align=0x1 PNP0c01: adding io range 0xc6c-0xc6f, size=0x4, align=0x1 PNP0c01: adding io range 0xcd6-0xcd7, size=0x2, align=0x1 PNP0c01: adding io range 0xf50-0xf57, size=0x8, align=0x1 pnpbios: handle 15 device ID PNP0c01 (010cd041) Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <Option ROM> at iomem 0xc0000-0xc7fff on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 atkbd0: [GIANT-LOCKED] psm0: current command byte:0065 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model IntelliMouse Explorer, device ID 4-00, 5 buttons psm0: config:00000000, flags:00000000, packet size:4 psm0: syncmask:08, syncbits:00 bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) ppc0: parallel port not found. ppc0: <Parallel port> failed to probe at irq 7 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio0: irq maps: 0x6003 0x6011 0x6001 0x6001 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0x6001 0x6001 0x6001 0x6001 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices unknown: <PNP0c02> can't assign resources (port) unknown: <PNP0c02> at port 0x580-0x58f,0x800-0x88f iomem 0xec000-0xeffff,0xf0000-0xfffff,0xff000000-0xffffffff,0x100000-0x7fffffff,0-0 x9ffff on isa0 unknown: <PNP0501> can't assign resources (port) unknown: <PNP0501> at port 0x3f8-0x3ff on isa0 unknown: <PNP0700> can't assign resources (port) unknown: <PNP0700> at port 0x3f0-0x3f5 on isa0 unknown: <PNP0f13> can't assign resources (irq) unknown: <PNP0f13> at irq 12 on isa0 unknown: <PNP0303> can't assign resources (port) unknown: <PNP0303> at port 0x60 on isa0 unknown: <PNP0800> failed to probe at port 0x61 on isa0 Device configuration finished. Timecounter "TSC" frequency 993332371 Hz quality -100 Timecounters tick every 10.000 msec Linux ELF exec handler installed lo0: bpf attached ata0-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin ata0-master: setting PIO4 on ServerWorks ROSB4 chip acd0: <SAMSUNG CD-ROM SN-124/q008> CDROM drive at ata0 as master acd0: read 4134KB/s (4134KB/s), 128KB buffer, PIO4 acd0: Reads: CDR, CDRW, CDDA stream, packet acd0: Writes: acd0: Audio: play, 255 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc Waiting 2 seconds for SCSI devices to settle (noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. (noperiph:ahc1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. amrd0: <LSILogic MegaRAID logical drive> on amr0 amrd0: 17278MB (35385344 sectors) RAID 1 (optimal) GEOM: new disk amrd0 [0] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/162/8 s:0 l:35385344 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure amrd0s1, start 0 length 18117296128 end 18117296127 GEOM: Configure amrd0a, start 0 length 134217728 end 134217727 GEOM: Configure amrd0b, start 134217728 length 2147483648 end 2281701375 GEOM: Configure amrd0c, start 0 length 18117296128 end 18117296127 GEOM: Configure amrd0d, start 2281701376 length 268435456 end 2550136831 GEOM: Configure amrd0e, start 2550136832 length 4294967296 end 6845104127 GEOM: Configure amrd0f, start 6845104128 length 4294967296 end 11140071423 GEOM: Configure amrd0g, start 11140071424 length 6977224704 end 18117296127 GEOM: Configure amrd0s1a, start 0 length 134217728 end 134217727 GEOM: Configure amrd0s1b, start 134217728 length 2147483648 end 2281701375 GEOM: Configure amrd0s1c, start 0 length 18117296128 end 18117296127 GEOM: Configure amrd0s1d, start 2281701376 length 268435456 end 2550136831 GEOM: Configure amrd0s1e, start 2550136832 length 4294967296 end 6845104127 GEOM: Configure amrd0s1f, start 6845104128 length 4294967296 end 11140071423 GEOM: Configure amrd0s1g, start 11140071424 length 6977224704 end 18117296127 (probe3:amr0:0:3:0): error 22 (probe3:amr0:0:3:0): Unretryable Error (probe15:amr0:1:0:0): error 22 (probe15:amr0:1:0:0): Unretryable Error (probe16:amr0:1:1:0): error 22 (probe16:amr0:1:1:0): Unretryable Error (probe4:amr0:0:4:0): error 22 (probe4:amr0:0:4:0): Unretryable Error (probe17:amr0:1:2:0): error 22 (probe17:amr0:1:2:0): Unretryable Error (probe5:amr0:0:5:0): error 22 (probe5:amr0:0:5:0): Unretryable Error (probe18:amr0:1:3:0): error 22 (probe18:amr0:1:3:0): Unretryable Error (probe7:amr0:0:8:0): error 22 (probe7:amr0:0:8:0): Unretryable Error (probe19:amr0:1:4:0): error 22 (probe19:amr0:1:4:0): Unretryable Error (probe8:amr0:0:9:0): error 22 (probe8:amr0:0:9:0): Unretryable Error ahc0: Selection Timeout on A:0. 0 SCBs aborted ahc1: Selection Timeout on A:0. 0 SCBs aborted (probe20:amr0:1:5:0): error 22 (probe20:amr0:1:5:0): Unretryable Error (probe9:amr0:0:10:0): error 22 (probe9:amr0:0:10:0): Unretryable Error ahc0: Selection Timeout on A:1. 0 SCBs aborted ahc1: Selection Timeout on A:1. 0 SCBs aborted (probe21:amr0:1:6:0): error 22 (probe21:amr0:1:6:0): Unretryable Error (probe10:amr0:0:11:0): error 22 (probe10:amr0:0:11:0): Unretryable Error ahc0: Selection Timeout on A:2. 0 SCBs aborted ahc1: Selection Timeout on A:2. 0 SCBs aborted (probe22:amr0:1:8:0): error 22 (probe22:amr0:1:8:0): Unretryable Error (probe11:amr0:0:12:0): error 22 (probe11:amr0:0:12:0): Unretryable Error ahc0: Selection Timeout on A:3. 0 SCBs aborted ahc1: Selection Timeout on A:3. 0 SCBs aborted (probe29:amr0:1:15:0): error 22 (probe29:amr0:1:15:0): Unretryable Error (probe12:amr0:0:13:0): error 22 (probe12:amr0:0:13:0): Unretryable Error ahc0: Selection Timeout on A:4. 0 SCBs aborted ahc1: Selection Timeout on A:4. 0 SCBs aborted (probe23:amr0:1:9:0): error 22 (probe23:amr0:1:9:0): Unretryable Error (probe13:amr0:0:14:0): error 22 (probe13:amr0:0:14:0): Unretryable Error ahc0: Selection Timeout on A:5. 0 SCBs aborted ahc1: Selection Timeout on A:15. 0 SCBs aborted (probe24:amr0:1:10:0): error 22 (probe24:amr0:1:10:0): Unretryable Error (probe14:amr0:0:15:0): error 22 (probe14:amr0:0:15:0): Unretryable Error (probe1:amr0:0:1:0): error 22 (probe1:amr0:0:1:0): Unretryable Error (probe2:amr0:0:2:0): error 22 (probe2:amr0:0:2:0): Unretryable Error (probe0:amr0:0:0:0): error 22 (probe0:amr0:0:0:0): Unretryable Error ahc0: Selection Timeout on A:15. 0 SCBs aborted ahc1: Selection Timeout on A:5. 0 SCBs aborted (probe25:amr0:1:11:0): error 22 (probe25:amr0:1:11:0): Unretryable Error ahc0: Selection Timeout on A:6. 0 SCBs aborted ahc1: Selection Timeout on A:6. 0 SCBs aborted (probe26:amr0:1:12:0): error 22 (probe26:amr0:1:12:0): Unretryable Error ahc0: Selection Timeout on A:8. 0 SCBs aborted ahc1: Selection Timeout on A:8. 0 SCBs aborted (probe27:amr0:1:13:0): error 22 (probe27:amr0:1:13:0): Unretryable Error ahc0: Selection Timeout on A:9. 0 SCBs aborted ahc1: Selection Timeout on A:9. 0 SCBs aborted (probe28:amr0:1:14:0): error 22 (probe28:amr0:1:14:0): Unretryable Error ahc0: Selection Timeout on A:10. 0 SCBs aborted ahc1: Selection Timeout on A:10. 0 SCBs aborted ahc0: Selection Timeout on A:11. 0 SCBs aborted ahc1: Selection Timeout on A:11. 0 SCBs aborted ahc0: Selection Timeout on A:12. 0 SCBs aborted ahc1: Selection Timeout on A:12. 0 SCBs aborted ahc0: Selection Timeout on A:13. 0 SCBs aborted ahc1: Selection Timeout on A:13. 0 SCBs aborted ahc0: Selection Timeout on A:14. 0 SCBs aborted ahc1: Selection Timeout on A:14. 0 SCBs aborted ses0 at amr0 bus 0 target 6 lun 0 ses0: <DELL 1x3 U2W SCSI BP 1.21> Fixed Processor SCSI-2 device ses0: Serial Number 1 ses0: SAF-TE Compliant Device pass0 at amr0 bus 0 target 6 lun 0 pass0: <DELL 1x3 U2W SCSI BP 1.21> Fixed Processor SCSI-2 device pass0: Serial Number 1 pt0 at amr0 bus 0 target 6 lun 0 pt0: <DELL 1x3 U2W SCSI BP 1.21> Fixed Processor SCSI-2 device pt0: Serial Number 1 SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x00000000 VER: 0x00040011 LDR: 0x01000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff ioapic0: routing intpin 1 (IRQ 1) to cluster 0 ioapic0: routing intpin 4 (IRQ 4) to cluster 0 ioapic0: routing intpin 6 (IRQ 6) to cluster 0 ioapic0: routing intpin 8 (IRQ 8) to cluster 0 ioapic0: routing intpin 12 (IRQ 12) to cluster 0 ioapic0: routing intpin 13 (IRQ 13) to cluster 0 ioapic0: routing intpin 14 (IRQ 14) to cluster 0 ioapic0: routing intpin 15 (IRQ 15) to cluster 0 ioapic1: routing intpin 0 (IRQ 16) to cluster 0 ioapic1: routing intpin 1 (IRQ 17) to cluster 0 ioapic1: routing intpin 9 (IRQ 25) to cluster 0 ioapic1: routing intpin 11 (IRQ 27) to cluster 0 ioapic1: routing intpin 12 (IRQ 28) to cluster 0 Mounting root from ufs:/dev/amrd0s1a start_init: trying /sbin/init fxp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6 fxp1: Microcode loaded, int_delay: 1000 usec bundle_max: 6 fxp1: Microcode loaded, int_delay: 1000 usec bundle_max: 6 fxp0: Microcode loaded, int_delay: 1000 usec bundle_max: 6 --------------------------------------- Robin P. Blanchard Systems Integration Specialist Georgia Center for Continuing Education fon: 706.542.2404 < > fax: 706.542.6546 ---------------------------------------Received on Mon May 24 2004 - 10:15:02 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:37:54 UTC