System is very recent (last night) cvsup of RELENG_5. Motherboard is Intel D865PERL. The system is setup to collect a dump after a panic, but none is ever found. Also, the corrupted output after "Shutting down ACPI" is about as good as it gets... sometimes the console (vga or serial) displays just one or two "random" letters (usually an "s"). It doesn't appear that disabling ACPI has any effect on this problem. Shutdown -p now always performs a power off. The system is temporarily a spare, so I can do anything that you think may help. The following is from a boot -v and "shutdown -r now" from the serial console. Console: serial port BIOS drive A: is disk0 BIOS drive B: is disk1 BIOS drive C: is disk2 BIOS 639kB/521408kB available memory FreeBSD/i386 bootstrap loader, Revision 1.1 (root_at_comm-server.support.bsd1.net, Wed Oct 6 21:11:51 EDT 2004) Loading /boot/defaults/loader.conf /boot/kernel/kernel text=0x425ed0 data=0x7d054+0x4acec syms=[0x4+0x59e30+0x4+0x6ee3a] /boot/kernel/acpi.ko text=0x3fa04 data=0x1be4+0x110c syms=[0x4+0x72a0+0x4+0x9743] SMAP type=01 base=0000000000000000 len=000000000009fc00 SMAP type=02 base=000000000009fc00 len=0000000000000400 SMAP type=02 base=00000000000e6000 len=000000000001a000 SMAP type=01 base=0000000000100000 len=000000001fd30000 SMAP type=04 base=000000001fe30000 len=000000000000e6d2 SMAP type=02 base=000000001ff10000 len=0000000000020000 SMAP type=03 base=000000001ff30000 len=0000000000010000 SMAP type=04 base=000000001ff40000 len=00000000000b0000 SMAP type=02 base=000000001fff0000 len=0000000000010000 SMAP type=02 base=00000000fecf0000 len=0000000000001000 SMAP type=02 base=00000000fed20000 len=0000000000080000 Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.3-BETA7 #0: Wed Oct 6 21:39:12 EDT 2004 root_at_comm-server.support.bsd1.net:/usr/obj/var/cvsup/usr/src/sys/GENERIC Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a0d000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0a0d294. Table 'FACP' at 0x1ff30200 Table 'APIC' at 0x1ff30300 MADT: Found table at 0x1ff30300 MP Configuration Table version 1.4 found at 0xc00fc610 APIC: Using the MADT enumerator. MADT: Found CPU APIC ID 0 ACPI ID 1: enabled SMP: Added CPU 0 (AP) MADT: Found CPU APIC ID 1 ACPI ID 2: enabled SMP: Added CPU 1 (AP) ACPI APIC Table: <INTEL PRODUCT8> Calibrating clock(s) ... i8254 clock: 1193124 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 2394008716 Hz CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2394.01-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf29 Stepping = 9 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA ,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Hyperthreading: 2 logical CPUs real memory = 534970368 (510 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000c29000 - 0x000000001f507fff, 512618496 bytes (125151 pages) avail memory = 513937408 (490 MB) APIC ID: physical 0, logical 0:0 APIC ID: physical 1, logical 0:1 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 bios32: Found BIOS32 Service Directory header at 0xc00f0000 bios32: Entry = 0xf0010 (c00f0010) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0x31 pnpbios: Found PnP BIOS data at 0xc00f3e80 pnpbios: Entry = f0000:44aa Rev = 1.0 Other BIOS signatures found: APIC: CPU 0 has ACPI ID 1 APIC: CPU 1 has ACPI ID 2 MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000 ioapic0: Routing external 8259A's -> intpin 0 ioapic0: intpin 0 -> ExtINT (edge, high) ioapic0: intpin 1 -> ISA IRQ 1 (edge, high) ioapic0: intpin 2 -> ISA IRQ 2 (edge, high) ioapic0: intpin 3 -> ISA IRQ 3 (edge, high) ioapic0: intpin 4 -> ISA IRQ 4 (edge, high) ioapic0: intpin 5 -> ISA IRQ 5 (edge, high) ioapic0: intpin 6 -> ISA IRQ 6 (edge, high) ioapic0: intpin 7 -> ISA IRQ 7 (edge, high) ioapic0: intpin 8 -> ISA IRQ 8 (edge, high) ioapic0: intpin 9 -> ISA IRQ 9 (edge, high) ioapic0: intpin 10 -> ISA IRQ 10 (edge, high) ioapic0: intpin 11 -> ISA IRQ 11 (edge, high) ioapic0: intpin 12 -> ISA IRQ 12 (edge, high) ioapic0: intpin 13 -> ISA IRQ 13 (edge, high) ioapic0: intpin 14 -> ISA IRQ 14 (edge, high) ioapic0: intpin 15 -> ISA IRQ 15 (edge, high) ioapic0: intpin 16 -> PCI IRQ 16 (level, low) ioapic0: intpin 17 -> PCI IRQ 17 (level, low) ioapic0: intpin 18 -> PCI IRQ 18 (level, low) ioapic0: intpin 19 -> PCI IRQ 19 (level, low) ioapic0: intpin 20 -> PCI IRQ 20 (level, low) ioapic0: intpin 21 -> PCI IRQ 21 (level, low) ioapic0: intpin 22 -> PCI IRQ 22 (level, low) ioapic0: intpin 23 -> PCI IRQ 23 (level, low) lapic0: Routing NMI -> LINT1 lapic1: Routing NMI -> LINT1 MADT: intr override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 ioapic0: intpin 2 trigger: edge ioapic0: intpin 2 polarity: high MADT: intr override: source 9, irq 9 ioapic0: intpin 9 trigger: level ioapic0: intpin 9 polarity: high ioapic0 <Version 2.0> irqs 0-23 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x00050014 LDR: 0x01000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff wlan: <802.11 Link Layer> random: <entropy source, Software, Yarrow> io: <I/O> mem: <memory> Pentium Pro MTRR support enabled null: <null device, zero device> npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <INTEL PRODUCT8> on motherboard acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x80000094 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25708086) pcibios: BIOS version 2.10 Found $PIR table, 12 entries at 0xc00f3d30 PCI-Only Interrupts: none Location Bus Device Pin Link IRQs embedded 1 0 A 0x60 3 4 5 6 7 9 10 11 12 14 15 embedded 1 0 B 0x61 3 4 5 6 7 9 10 11 12 14 15 embedded 0 2 A 0x60 3 4 5 6 7 9 10 11 12 14 15 embedded 0 1 A 0x62 3 4 5 6 7 9 10 11 12 14 15 embedded 2 8 A 0x68 3 4 5 6 7 9 10 11 12 14 15 embedded 0 31 A 0x62 3 4 5 6 7 9 10 11 12 14 15 embedded 0 31 B 0x61 3 4 5 6 7 9 10 11 12 14 15 embedded 0 29 A 0x60 3 4 5 6 7 9 10 11 12 14 15 embedded 0 29 B 0x63 3 4 5 6 7 9 10 11 12 14 15 embedded 0 29 C 0x62 3 4 5 6 7 9 10 11 12 14 15 embedded 0 29 D 0x6b 3 4 5 6 7 9 10 11 12 14 15 slot 1 2 0 A 0x69 3 4 5 6 7 9 10 11 12 14 15 slot 1 2 0 B 0x6a 3 4 5 6 7 9 10 11 12 14 15 slot 1 2 0 C 0x6b 3 4 5 6 7 9 10 11 12 14 15 slot 1 2 0 D 0x68 3 4 5 6 7 9 10 11 12 14 15 slot 2 2 1 A 0x6a 3 4 5 6 7 9 10 11 12 14 15 slot 2 2 1 B 0x69 3 4 5 6 7 9 10 11 12 14 15 slot 2 2 1 C 0x68 3 4 5 6 7 9 10 11 12 14 15 slot 2 2 1 D 0x6b 3 4 5 6 7 9 10 11 12 14 15 slot 3 2 2 A 0x61 3 4 5 6 7 9 10 11 12 14 15 slot 3 2 2 B 0x62 3 4 5 6 7 9 10 11 12 14 15 slot 3 2 2 C 0x63 3 4 5 6 7 9 10 11 12 14 15 slot 3 2 2 D 0x60 3 4 5 6 7 9 10 11 12 14 15 slot 4 2 3 A 0x63 3 4 5 6 7 9 10 11 12 14 15 slot 4 2 3 B 0x62 3 4 5 6 7 9 10 11 12 14 15 slot 4 2 3 C 0x69 3 4 5 6 7 9 10 11 12 14 15 slot 4 2 3 D 0x6a 3 4 5 6 7 9 10 11 12 14 15 slot 5 2 4 A 0x62 3 4 5 6 7 9 10 11 12 14 15 slot 5 2 4 B 0x6b 3 4 5 6 7 9 10 11 12 14 15 slot 5 2 4 C 0x60 3 4 5 6 7 9 10 11 12 14 15 slot 5 2 4 D 0x68 3 4 5 6 7 9 10 11 12 14 15 embedded 2 7 A 0x61 3 4 5 6 7 9 10 11 12 14 15 AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi0: Power Button (fixed) ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 3, width = 0 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 4, width = 1 ACPI timer looks GOOD min = 3, max = 3, width = 0 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 cpu1: Failed to attach throttling P_CNT pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 ACPI PCI link initial configuration: pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base f8000000, size 26, enabled found-> vendor=0x8086, dev=0x2570, revid=0x02 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2571, revid=0x02 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000cc00, size 5, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x24d2, revid=0x02 bus=0, slot=29, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=16 map[20]: type 4, range 32, base 0000d000, size 5, enabled pcib0: matched entry for 0.29.INTB pcib0: slot 29 INTB hardwired to IRQ 19 found-> vendor=0x8086, dev=0x24d4, revid=0x02 bus=0, slot=29, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=19 map[20]: type 4, range 32, base 0000d400, size 5, enabled pcib0: matched entry for 0.29.INTC pcib0: slot 29 INTC hardwired to IRQ 18 found-> vendor=0x8086, dev=0x24d7, revid=0x02 bus=0, slot=29, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=18 map[20]: type 4, range 32, base 0000d800, size 5, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x24de, revid=0x02 bus=0, slot=29, func=3 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=16 map[10]: type 1, range 32, base febffc00, size 10, enabled pcib0: matched entry for 0.29.INTD pcib0: slot 29 INTD hardwired to IRQ 23 found-> vendor=0x8086, dev=0x24dd, revid=0x02 bus=0, slot=29, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=23 powerspec 2 supports D0 D3 current D0 found-> vendor=0x8086, dev=0x244e, revid=0xc2 bus=0, slot=30, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x0080, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x02 (500 ns) found-> vendor=0x8086, dev=0x24d0, revid=0x02 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x010f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000ffa0, size 4, enabled found-> vendor=0x8086, dev=0x24db, revid=0x02 bus=0, slot=31, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 map[10]: type 4, range 32, base 0000ec00, size 3, enabled map[14]: type 4, range 32, base 0000e800, size 2, enabled map[18]: type 4, range 32, base 0000e400, size 3, enabled map[1c]: type 4, range 32, base 0000e000, size 2, enabled map[20]: type 4, range 32, base 0000dc00, size 4, enabled pcib0: matched entry for 0.31.INTA pcib0: slot 31 INTA hardwired to IRQ 18 found-> vendor=0x8086, dev=0x24d1, revid=0x02 bus=0, slot=31, func=2 class=01-01-8f, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x02a0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=18 map[20]: type 4, range 32, base 0000c800, size 5, enabled pcib0: matched entry for 0.31.INTB pcib0: slot 31 INTB hardwired to IRQ 17 found-> vendor=0x8086, dev=0x24d3, revid=0x02 bus=0, slot=31, func=3 class=0c-05-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=17 map[18]: type 1, range 32, base febff800, size 9, enabled map[1c]: type 1, range 32, base febff400, size 8, enabled pcib0: matched entry for 0.31.INTB pcib0: slot 31 INTB hardwired to IRQ 17 found-> vendor=0x8086, dev=0x24d5, revid=0x02 bus=0, slot=31, func=5 class=04-01-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=17 powerspec 2 supports D0 D3 current D0 agp0: <Intel 82865 host to AGP bridge> mem 0xf8000000-0xfbffffff at device 0.0 on pci0 agp0: Reserved 0x4000000 bytes for rid 0x10 type 3 at 0xf8000000 agp0: allocating GATT for aperture of size 64M pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xf000-0xfff pcib1: memory decode 0xfc900000-0xfe9fffff pcib1: prefetched decode 0xe4700000-0xf47fffff ACPI PCI link initial configuration: pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 map[10]: type 1, range 32, base fd000000, size 24, enabled pcib1: device (null) requested decoded memory range 0xfd000000-0xfdffffff map[14]: type 3, range 32, base e8000000, size 27, enabled pcib1: device (null) requested decoded memory range 0xe8000000-0xefffffff map[18]: type 3, range 32, base f4780000, size 19, enabled pcib1: device (null) requested decoded memory range 0xf4780000-0xf47fffff pcib1: matched entry for 1.0.INTA pcib1: slot 0 INTA hardwired to IRQ 16 found-> vendor=0x10de, dev=0x0201, revid=0xa3 bus=1, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns) intpin=a, irq=16 powerspec 2 supports D0 D3 current D0 pci1: <display, VGA> at device 0.0 (no driver attached) uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xcc00-0xcc1f irq 16 at device 29.0 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xcc00 uhci0: [GIANT-LOCKED] usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xd000-0xd01f irq 19 at device 29.1 on pci0 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xd000 uhci1: [GIANT-LOCKED] usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xd400-0xd41f irq 18 at device 29.2 on pci0 uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0xd400 uhci2: [GIANT-LOCKED] usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xd800-0xd81f irq 16 at device 29.3 on pci0 uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0xd800 uhci3: [GIANT-LOCKED] usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3 usb3: USB revision 1.0 uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered pci0: <serial bus, USB> at device 29.7 (no driver attached) pcib2: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0xa000-0xbfff pcib2: memory decode 0xfea00000-0xfeafffff pcib2: prefetched decode 0xfff00000-0xfffff pcib2: Subtractively decoded bridge. ACPI PCI link initial configuration: pci2: <ACPI PCI bus> on pcib2 pci2: physical bus=2 map[10]: type 4, range 32, base 0000bc00, size 3, enabled pcib2: device (null) requested decoded I/O range 0xbc00-0xbc07 map[14]: type 4, range 32, base 0000b800, size 2, enabled pcib2: device (null) requested decoded I/O range 0xb800-0xb803 map[18]: type 4, range 32, base 0000b400, size 3, enabled pcib2: device (null) requested decoded I/O range 0xb400-0xb407 map[1c]: type 4, range 32, base 0000b000, size 2, enabled pcib2: device (null) requested decoded I/O range 0xb000-0xb003 map[20]: type 4, range 32, base 0000ac00, size 4, enabled pcib2: device (null) requested decoded I/O range 0xac00-0xac0f map[24]: type 1, range 32, base feaf0000, size 16, enabled pcib2: device (null) requested decoded memory range 0xfeaf0000-0xfeafffff pcib2: matched entry for 2.2.INTA pcib2: slot 2 INTA hardwired to IRQ 17 found-> vendor=0x105a, dev=0x6268, revid=0x02 bus=2, slot=2, func=0 class=01-04-85, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x0430, cachelnsz=16 (dwords) lattimer=0x20 (960 ns), mingnt=0x04 (1000 ns), maxlat=0x12 (4500 ns) intpin=a, irq=17 powerspec 1 supports D0 D1 D3 current D0 map[10]: type 4, range 32, base 0000a800, size 8, enabled pcib2: device (null) requested decoded I/O range 0xa800-0xa8ff map[14]: type 1, range 32, base feadfc00, size 8, enabled pcib2: device (null) requested decoded memory range 0xfeadfc00-0xfeadfcff pcib2: matched entry for 2.3.INTA pcib2: slot 3 INTA hardwired to IRQ 19 found-> vendor=0x1186, dev=0x1300, revid=0x10 bus=2, slot=3, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns) intpin=a, irq=19 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 4, range 32, base 0000a400, size 8, enabled pcib2: device (null) requested decoded I/O range 0xa400-0xa4ff map[14]: type 1, range 32, base feadf800, size 8, enabled pcib2: device (null) requested decoded memory range 0xfeadf800-0xfeadf8ff pcib2: matched entry for 2.4.INTA pcib2: slot 4 INTA hardwired to IRQ 18 found-> vendor=0x1186, dev=0x1300, revid=0x10 bus=2, slot=4, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns) intpin=a, irq=18 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base feade000, size 12, enabled pcib2: device (null) requested decoded memory range 0xfeade000-0xfeadefff map[14]: type 4, range 32, base 0000a000, size 6, enabled pcib2: device (null) requested decoded I/O range 0xa000-0xa03f pcib2: matched entry for 2.8.INTA pcib2: slot 8 INTA hardwired to IRQ 20 found-> vendor=0x8086, dev=0x1050, revid=0x01 bus=2, slot=8, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0117, statreg=0x0290, cachelnsz=16 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns) intpin=a, irq=20 powerspec 2 supports D0 D1 D2 D3 current D0 atapci0: <Promise PDC20270 UDMA100 controller> port 0xac00-0xac0f,0xb000-0xb003,0xb400-0xb407,0xb800-0xb803,0xbc00-0xbc07 mem 0xfeaf0000-0xfeafffff irq 17 at device 2.0 on pci2 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xac00 atapci0: [MPSAFE] ata2: channel #0 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0xbc00 atapci0: Reserved 0x4 bytes for rid 0x14 type 4 at 0xb800 ata2: reset tp1 mask=03 ostat0=50 ostat1=00 ata2-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90 ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata2-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata2: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata2: [MPSAFE] ata3: channel #1 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0xb400 atapci0: Reserved 0x4 bytes for rid 0x1c type 4 at 0xb000 ata3: reset tp1 mask=03 ostat0=50 ostat1=00 ata3-master: stat=0x90 err=0x90 lsb=0x90 msb=0x90 ata3-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata3-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata3: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata3: [MPSAFE] rl0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xa800 rl0: <D-Link DFE-530TX+ 10/100BaseTX> port 0xa800-0xa8ff mem 0xfeadfc00-0xfeadfcff irq 19 at device 3.0 on pci2 pcib2: device rl0 requested decoded I/O range 0xa800-0xa8ff miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl0: bpf attached rl0: Ethernet address: 00:0d:88:35:39:a0 rl0: [MPSAFE] rl1: Reserved 0x100 bytes for rid 0x10 type 4 at 0xa400 rl1: <D-Link DFE-530TX+ 10/100BaseTX> port 0xa400-0xa4ff mem 0xfeadf800-0xfeadf8ff irq 18 at device 4.0 on pci2 pcib2: device rl1 requested decoded I/O range 0xa400-0xa4ff miibus1: <MII bus> on rl1 rlphy1: <RealTek internal media interface> on miibus1 rlphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl1: bpf attached rl1: Ethernet address: 00:0d:88:37:d7:ba rl1: [MPSAFE] fxp0: <Intel 82801BA (D865) Pro/100 VE Ethernet> port 0xa000-0xa03f mem 0xfeade000-0xfeadefff irq 20 at device 8.0 on pci2 fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfeade000 fxp0: using memory space register mapping fxp0: PCI IDs: 8086 1050 8086 3020 0001 fxp0: Dynamic Standby mode is enabled miibus2: <MII bus> on fxp0 inphy0: <i82562ET 10/100 media interface> on miibus2 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: bpf attached fxp0: Ethernet address: 00:11:11:0a:46:7b fxp0: [MPSAFE] isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci1: <Intel ICH5 UDMA100 controller> port 0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.1 on pci0 atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0xffa0 ata0: channel #0 on atapci1 atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci1: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0-master: stat=0x90 err=0x01 lsb=0x14 msb=0xeb ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb ata0-slave: stat=0x00 err=0x01 lsb=0x7f msb=0x7f ata0: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> ata0: [MPSAFE] ata1: channel #1 on atapci1 atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci1: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=03 ostat0=50 ostat1=00 ata1-master: stat=0x10 err=0x01 lsb=0x14 msb=0xeb ata1-slave: stat=0x7f err=0x01 lsb=0x01 msb=0x01 ata1: reset tp2 stat0=10 stat1=7f devices=0x6<ATAPI_MASTER,ATA_SLAVE> ata1: [MPSAFE] atapci2: <Intel ICH5 SATA150 controller> port 0xdc00-0xdc0f,0xe000-0xe003,0xe400-0xe407,0xe800-0xe803,0xec00-0xec07 irq 18 at device 31.2 on pci0 atapci2: Reserved 0x10 bytes for rid 0x20 type 4 at 0xdc00 atapci2: [MPSAFE] ata4: channel #0 on atapci2 atapci2: Reserved 0x8 bytes for rid 0x10 type 4 at 0xec00 atapci2: Reserved 0x4 bytes for rid 0x14 type 4 at 0xe800 ata4: reset tp1 mask=03 ostat0=7f ostat1=7f ata4-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata4-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata4-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata4-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata4-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata4-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata4-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata4-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata4-slave: stat=0x7f err=0xff lsb=0xff msb=0xff ata4: reset tp2 stat0=ff stat1=ff devices=0x0 ata4: [MPSAFE] ata5: channel #1 on atapci2 atapci2: Reserved 0x8 bytes for rid 0x18 type 4 at 0xe400 atapci2: Reserved 0x4 bytes for rid 0x1c type 4 at 0xe000 ata5: reset tp1 mask=03 ostat0=7f ostat1=7f ata5-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata5-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata5-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata5-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata5-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata5-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata5-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata5-master: stat=0x7f err=0xff lsb=0xff msb=0xff ata5-slave: stat=0x7f err=0xff lsb=0xff msb=0xff ata5: reset tp2 stat0=ff stat1=ff devices=0x0 ata5: [MPSAFE] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) pci0: <multimedia, audio> at device 31.5 (no driver attached) acpi_button0: <Sleep Button> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbdc: RESET_KBD return code:00fa kbdc: RESET_KBD status:00aa kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x1d0000 atkbd0: [GIANT-LOCKED] psm0: unable to allocate IRQ psmcpnp0 irq 12 on acpi0 psm0: current command byte:0065 kbdc: TEST_AUX_PORT status:0000 kbdc: RESET_AUX return code:00fa kbdc: RESET_AUX status:00aa kbdc: RESET_AUX ID:0000 kbdc: RESET_AUX return code:00fa kbdc: RESET_AUX status:00aa kbdc: RESET_AUX ID:0000 psm: status 00 03 50 psm: status 00 00 50 psm: status 00 03 50 psm: status 00 03 50 psm: data 08 00 00 psm: status 00 03 50 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model IntelliMouse Explorer, device ID 4-00, 5 buttons psm0: config:00000000, flags:00000008, packet size:4 psm0: syncmask:08, syncbits:00 fdc0: <floppy drive controller> port 0x3f7,0x3f4-0x3f5,0x3f2-0x3f3,0x3f0-0x3f1 irq 6 drq 2 on acpi0 fdc0: ic_type 90 part_id 73 fdc0: [MPSAFE] fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0 0 0 0 sio0 port 0x3f8-0x3ff irq 4 on acpi0 sio0: type 16550A, console ppc0: using extended I/O port range ppc0: SPP ppc0 port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 plip0: bpf attached lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 unknown: not probed (disabled) unknown: not probed (disabled) ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it ppc: ppc0 already exists; skipping it sio: sio0 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 ex_isa_identify() unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff ahc_isa_probe 10: ioport 0xac00 alloc failed ahc_isa_probe 11: ioport 0xbc00 alloc failed ahc_isa_probe 12: ioport 0xcc00 alloc failed ahc_isa_probe 13: ioport 0xdc00 alloc failed ahc_isa_probe 14: ioport 0xec00 alloc failed sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <ISA Option ROM> at iomem 0xcc000-0xd57ff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x100> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0 0 0 0 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0: vga0, vga, type:VGA (5), flags:0x7007f fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 54 80 bf 1f 00 4f 0d 0e 00 00 01 40 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 54 80 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. procfs registered Timecounter "TSC" frequency 2394008716 Hz quality -100 Timecounters tick every 10.000 msec lo0: bpf attached cpu0: set speed to 100.0% acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% ata0-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin ata0-master: setting PIO4 on Intel ICH5 chip ata0-master: setting UDMA33 on Intel ICH5 chip acd0: <CREATIVE CD5233E-N/0.20> CDROM drive at ata0 as master acd0: 128KB buffer, UDMA33 acd0: Reads: CDR, CDRW, CDDA stream, packet acd0: Writes: acd0: Audio: play, 255 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc GEOM: Configure fd0a, start 0 length 1474560 end 1474559 GEOM: Configure fd0b, start 0 length 1474560 end 1474559 GEOM: Configure fd0c, start 0 length 1474560 end 1474559 ata1: reiniting channel .. ata1: reset tp1 mask=03 ostat0=10 ostat1=00 ata1-master: stat=0x10 err=0x01 lsb=0x14 msb=0xeb ata1-slave: stat=0x7f err=0x01 lsb=0x01 msb=0x01 ata1: reset tp2 stat0=10 stat1=7f devices=0x6<ATAPI_MASTER,ATA_SLAVE> ata1: resetting done .. ata1: reiniting channel .. ata1-slave: FAILURE - ATA_IDENTIFY timed out ata1: reiniting channel .. ata1-slave: FAILURE - ATA_IDENTIFY timed out ata1-master: pio=0x0b wdma=0x21 udma=0xffffffff cable=40pin ata1-master: FAILURE - SETFEATURES SET TRANSFER MODE status=1<ERROR> error=4<ABORTED> ata1-master: FAILURE setting PIO3 on Intel ICH5 chip ata1: device config done .. ata1-slave: FAILURE - ATA_IDENTIFY timed out ata1-master: pio=0x0b wdma=0x21 udma=0xffffffff cable=40pin ata1-master: FAILURE - SETFEATURES SET TRANSFER MODE status=1<ERROR> error=4<ABORTED> ata1-master: FAILURE setting PIO3 on Intel ICH5 chip afd0: <IOMEGA ZIP 100 ATAPI/03.H> removable drive at ata1 as master afd0: 96MB (196608 sectors), 96 cyls, 64 heads, 32 S/T, 512 B/S afd0: 4096KB/s, BIOSPIO GEOM: new disk afd0 ata2-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata2-master: setting PIO4 on Promise PDC20270 chip ata2-master: setting UDMA100 on Promise PDC20270 chip ad4: <ST380011A/3.06> ATA-6 disk at ata2-master ad4: 76319MB (156301488 sectors), 155061 C, 16 H, 63 S, 512 B ad4: 16 secs/int, 1 depth queue, UDMA100 ata3-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata3-master: setting PIO4 on Promise PDC20270 chip ata3-master: setting UDMA100 on Promise PDC20270 chip ad6: <ST380011A/3.06> ATA-6 disk at ata3-master ad6: 76319MB (156301488 sectors), 155061 C, 16 H, 63 S, 512 B ad6: 16 secs/int, 1 depth queue, UDMA100 GEOM: new disk ad4 GEOM: new disk ad6 lun 0 magic_0 0x00000000 magic_1 0x00000000 flags 0x20104 20104<READY,SPAN> total_disks 2 generation 600 width 1 heads 255 sectors 63 cylinders 9729 total_sectors 156301312 interleave 128 reserved 63 offset 0 disk 0: flags = 0x0b b<ONLINE,ASSIGNED,PRESENT> ad6 sectors 156301425 disk 1: flags = 0x0b b<ONLINE,ASSIGNED,PRESENT> ad4 sectors 156301425 ar0: 76319MB <ATA RAID1 array> [9729/255/63] status: READY subdisks: disk0 READY on ad6 at ata3-master disk1 READY on ad4 at ata2-master SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x01000000 VER: 0x00050014 LDR: 0x02000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00010400 TPR: 0x00000000 SVR: 0x000001ff ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0 ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0 ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0 ioapic0: routing intpin 7 (ISA IRQ 7) to cluster 0 ioapic0: routing intpin 8 (ISA IRQ 8) to cluster 0 ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0 ioapic0: routing intpin 12 (ISA IRQ 12) to cluster 0 ioapic0: routing intpin 13 (ISA IRQ 13) to cluster 0 ioapic0: routing intpin 14 (ISA IRQ 14) to cluster 0 ioapic0: routing intpin 15 (ISA IRQ 15) to cluster 0 ioapic0: routing intpin 16 (PCI IRQ 16) to cluster 0 ioapic0: routing intpin 17 (PCI IRQ 17) to cluster 0 ioapic0: routing intpin 18 (PCI IRQ 18) to cluster 0 ioapic0: routing intpin 19 (PCI IRQ 19) to cluster 0 ioapic0: routing intpin 20 (PCI IRQ 20) to cluster 0 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:83875302 [1] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:83875365 l:72421020 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad4s1, start 32256 length 42944154624 end 42944186879 GEOM: Configure ad4s2, start 42944186880 length 37079562240 end 80023749119 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:83875302 [1] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:83875365 l:72421020 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad6s1, start 32256 length 42944154624 end 42944186879 GEOM: Configure ad6s2, start 42944186880 length 37079562240 end 80023749119 GEOM: new disk ar0 GEOM: Configure ad4s1a, start 0 length 4294967296 end 4294967295 GEOM: Configure ad4s1b, start 4294967296 length 2147483648 end 6442450943 GEOM: Configure ad4s1c, start 0 length 42944154624 end 42944154623 GEOM: Configure ad4s1d, start 6442450944 length 8589934592 end 15032385535 GEOM: Configure ad4s1e, start 15032385536 length 8589934592 end 23622320127 GEOM: Configure ad4s1f, start 23622320128 length 4294967296 end 27917287423 GEOM: Configure ad4s1g, start 27917287424 length 4294967296 end 32212254719 GEOM: Configure ad4s1h, start 32212254720 length 10731899904 end 42944154623 GEOM: Configure ad4s2c, start 0 length 37079562240 end 37079562239 GEOM: Configure ad4s2d, start 0 length 37079562240 end 37079562239 GEOM: Configure ad6s1a, start 0 length 4294967296 end 4294967295 GEOM: Configure ad6s1b, start 4294967296 length 2147483648 end 6442450943 GEOM: Configure ad6s1c, start 0 length 42944154624 end 42944154623 GEOM: Configure ad6s1d, start 6442450944 length 8589934592 end 15032385535 GEOM: Configure ad6s1e, start 15032385536 length 8589934592 end 23622320127 GEOM: Configure ad6s1f, start 23622320128 length 4294967296 end 27917287423 GEOM: Configure ad6s1g, start 27917287424 length 4294967296 end 32212254719 GEOM: Configure ad6s1h, start 32212254720 length 10731899904 end 42944154623 GEOM: Configure ad6s2c, start 0 length 37079562240 end 37079562239 GEOM: Configure ad6s2d, start 0 length 37079562240 end 37079562239 [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:83875302 [1] f:00 typ:165 s(CHS):1023/255/63 e(CHS):1023/254/63 s:83875365 l:72421020 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ar0s1, start 32256 length 42944154624 end 42944186879 GEOM: Configure ar0s2, start 42944186880 length 37079562240 end 80023749119 GEOM: Configure ar0s1a, start 0 length 4294967296 end 4294967295 GEOM: Configure ar0s1b, start 4294967296 length 2147483648 end 6442450943 GEOM: Configure ar0s1c, start 0 length 42944154624 end 42944154623 GEOM: Configure ar0s1d, start 6442450944 length 8589934592 end 15032385535 GEOM: Configure ar0s1e, start 15032385536 length 8589934592 end 23622320127 GEOM: Configure ar0s1f, start 23622320128 length 4294967296 end 27917287423 GEOM: Configure ar0s1g, start 27917287424 length 4294967296 end 32212254719 GEOM: Configure ar0s1h, start 32212254720 length 10731899904 end 42944154623 GEOM: Configure ar0s2c, start 0 length 37079562240 end 37079562239 GEOM: Configure ar0s2d, start 0 length 37079562240 end 37079562239 Mounting root from ufs:/dev/ar0s1a start_init: trying /sbin/init Pre-seeding PRNG: kickstart. Loading configuration files. Entropy harvesting: interrupts ethernet point_to_point kickstart. kernel dumps on /dev/ar0s1b swapon: adding /dev/ar0s1b as swap device Starting file system checks: /dev/ar0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ar0s1a: clean, 2000705 free (689 frags, 250002 blocks, 0.0% fragmentation) /dev/ar0s1d: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ar0s1d: clean, 3309627 free (39699 frags, 408741 blocks, 1.0% fragmentation) /dev/ar0s1e: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ar0s1e: clean, 3853627 free (331 frags, 481662 blocks, 0.0% fragmentation) /dev/ar0s1f: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ar0s1f: clean, 2029020 free (28 frags, 253624 blocks, 0.0% fragmentation) /dev/ar0s1g: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ar0s1g: clean, 2029025 free (25 frags, 253625 blocks, 0.0% fragmentation) /dev/ar0s1h: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ar0s1h: clean, 5074382 free (22 frags, 634295 blocks, 0.0% fragmentation) /dev/ar0s2d: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/ar0s2d: clean, 17533931 free (27 frags, 2191738 blocks, 0.0% fragmentation) Setting hostname: comm-server.support.bsd1.net. lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x5 Starting dhclient. fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 options=8<VLAN_MTU> inet6 fe80::211:11ff:fe0a:467b%fxp0 prefixlen 64 scopeid 0x3 inet 192.168.210.51 netmask 0xffffff00 broadcast 192.168.210.255 ether 00:11:11:0a:46:7b media: Ethernet autoselect (100baseTX <full-duplex>) status: active Additional routing options: IP gateway=YES. Starting devd. Mounting NFS file systems:. Starting syslogd. Oct 7 14:40:30 comm-server syslogd: kernel boot file is /boot/kernel/kernel Checking for core dump on /dev/ar0s1b ... savecore: no dumps found Setting date via ntp. Looking for host 192.168.210.1 and service ntp host found : free.bsd1.net 7 Oct 14:40:31 ntpdate[311]: step time server 192.168.210.1 offset 0.447919 sec ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout /usr/X11R6/lib/aout Starting usbd. Starting local daemons:. Updating motd. Configuring syscons: blanktime. Starting sshd. Initial i386 initialization:. Additional ABI support:. Starting cron. Local package initialization:. Additional TCP options:. Starting inetd. Starting background file system checks in 60 seconds. Thu Oct 7 14:40:32 EDT 2004 FreeBSD/i386 (comm-server.support.bsd1.net) (ttyd0) login: root Password: Oct 7 14:40:52 comm-server login: ROOT LOGIN (root) ON ttyd0 erase ^H, kill ^U, intr ^C status ^T FreeBSD cons25 [comm-server.support.bsd1.net:ttyd0:/root ]> ls /var/crash minfree [comm-server.support.bsd1.net:ttyd0:/root ]> pstat -s Device 1K-blocks Used Avail Capacity /dev/ar0s1b 2097152 0 2097152 0% [comm-server.support.bsd1.net:ttyd0:/root ]> shutdown -r now Shutdown NOW! shutdown: [pid 507] *** FINAL System shutdown message from root_at_comm-server.support.bsd1.net *** System going down IMMEDIATELY Oct 7 14:41:09 comm-server shutdown: reboot by root: [comm-server.support.bsd1.net:ttyd0:/root ]> System shutdown time has arrived Stopping inetd. Shutting down daemon processes:. Stopping cron. Shutting down local daemons:. Writing entropy file:. swapoff: removing /dev/ar0s1b as swap device . Oct 7 14:41:11 comm-server syslogd: exiting on signal 15 boot() called on cpu#1 Waiting (max 60 seconds) for system process `vnlru' to stop...done Waiting (max 60 seconds) for system process `bufdaemon' to stop...done Waiting (max 60 seconds) for system process `syncer' to stop... Syncing disks, vnodes remaining...3 0 0 0 done No buffers busy after final sync Uptime: 1m20s unknown: wake_prep disabled wake for \_SB_.PCI0.P0P2.TANA (S5) pcib2: wake_prep disabled wake for \_SB_.PCI0.P0P3 (S5) unknown: wake_prep disabled wake for \_SB_.PCI0.AC97 (S5) uhci0: wake_prep disabled wake for \_SB_.PCI0.USB0 (S5) uhci1: wake_prep disabled wake for \_SB_.PCI0.USB1 (S5) uhci2: wake_prep disabled wake for \_SB_.PCI0.USB2 (S5) uhci3: wake_prep disabled wake for \_SB_.PCI0.USB3 (S5) unknown: wake_prep disabled wake for \_SB_.PCI0.USB7 (S5) sio0: wake_prep disabled wake for \_SB_.PCI0.SBRG.UAR1 (S5) acpi_button0: wake_prep disabled wake for \_SB_.SLPB (S5) Shutting down ACPI kk e rFnaetla lt rdaopu b1l2e wfiatuhl ti:n t eerirpu p=t s0 xdci1s9aabcl4ebdc e s p F=a t0axl5 4t6r0acp1 91a2 :e bppa g=e 0fxa0u l tc pwuhiidl e= i1n; kaeprince li d m=o d0e1 cppauniidc := d0o;u balpei cf aiudl t= 0c0p u ifda u=l t1 v ibrotouta(l) acdadlrleesds o=n 0cxp1u0#010 2U p tfiamuel:t 1cmo2d1es = supervisor read, page not present instruction pointer = 0x8:0x10002 stack pointer = 0x10:0xd40ecad8 frame pointer = 0x10:0xd40ecb98 code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = resume, IOPL = 0 current process = 37 (swi5: clock sio) trap number = 12Received on Thu Oct 07 2004 - 17:01:26 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:16 UTC