On Sat, Oct 09, 2004 at 01:19:58PM -0400, Anish Mistry wrote: > Running 6-CURRENT. Between 09.25.18.00.00 UTC and 09.26.12.00.00 UTC some > commit seemed to break suspending on my laptop. Whenever I try to suspend it > reboots. Before this suspend was working well. The panic message seem to > indicate an ATA issue. > http://am-productions.biz/docs/littleguy.asl.gz > http://am-productions.biz/docs/littleguy-dmesg.boot.gz > -- > Anish Mistry Sort of "me too". I'm running 5.3BETA7 (2004-10-06 10:08UTC). Whenever I give the zzz command it tries to suspend but gets stuck in a lock-related panic: #zzz Sleeping on "atasusp" with the following non-sleepable locks held: exclusive sleep mutex ATA state lock r=0 (0xc1075318) locked _at_ /usr/src/sys/dev/ata/ata-all.c:341 KDB: enter: witness-warn . panic uptime : ..... panic: _mtx_lock_sleep: recursed on non-recursive mutex ATA state lock _at_ /usr/src/sys/dev/ata/ata-queue.c:180 . panic panic: _mtx_lock_sleep: recursed on non-recursive mutex ATA state lock _at_ /usr/src/sys/dev/ata/ata-queue.c:86 . show witness (top ones shown:) ATA queue lock ata-queue.c:174 ATA state lock ata-all.c:341 bio queue geom_io.c:65 ATA disk bioqueue lcok ata-disk.c:236 ATA CD bioqueue lock atapi-cd.c:1100 ... Giving the panic command doesn't give me a crash dump. apm_enable is set to NO and dumpdev is set to /dev/ad0s1b in /etc/rc.conf dmesg -v: Copyright (c) 1992-2004 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.3-BETA7 #0: Tue Oct 5 22:35:15 CEST 2004 root_at_82-168-140-74-bbxl.xdsl.tiscali.nl:/usr/obj/usr/src/sys/RENE_2004-09-05d WARNING: WITNESS option enabled, expect reduced performance. Preloaded elf kernel "/boot/kernel/kernel" at 0xc07ea000. Preloaded elf module "/boot/kernel/vesa.ko" at 0xc07ea1f4. Preloaded elf module "/boot/kernel/if_fxp.ko" at 0xc07ea2a0. Preloaded elf module "/boot/kernel/miibus.ko" at 0xc07ea34c. Preloaded elf module "/boot/kernel/snd_cs4281.ko" at 0xc07ea3f8. Preloaded elf module "/boot/kernel/sound.ko" at 0xc07ea4a8. Preloaded elf module "/boot/kernel/random.ko" at 0xc07ea554. Preloaded elf module "/boot/kernel/speaker.ko" at 0xc07ea600. Preloaded elf module "/boot/kernel/mem.ko" at 0xc07ea6ac. Preloaded elf module "/boot/kernel/io.ko" at 0xc07ea754. Preloaded elf module "/boot/kernel/intpm.ko" at 0xc07ea7fc. Preloaded elf module "/boot/kernel/smbus.ko" at 0xc07ea8a8. Preloaded elf module "/boot/kernel/cd9660_iconv.ko" at 0xc07ea954. Preloaded elf module "/boot/kernel/libiconv.ko" at 0xc07eaa08. Preloaded elf module "/boot/kernel/cd9660.ko" at 0xc07eaab8. Preloaded elf module "/boot/kernel/msdosfs_iconv.ko" at 0xc07eab64. Preloaded elf module "/boot/kernel/msdosfs.ko" at 0xc07eac18. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc07eacc4. Calibrating clock(s) ... i8254 clock: 1193083 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 497559801 Hz CPU: Intel Celeron (497.56-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x683 Stepping = 3 Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 201261056 (191 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000000826000 - 0x000000000bc5ffff, 188981248 bytes (46138 pages) avail memory = 191459328 (182 MB) bios32: Found BIOS32 Service Directory header at 0xc00f63a0 bios32: Entry = 0xfd8a6 (c00fd8a6) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xfd890+0x134 pnpbios: Found PnP BIOS data at 0xc00f63d0 pnpbios: Entry = f0000:aa9f Rev = 1.0 Other BIOS signatures found: null: <null device, zero device> random: <entropy source, Software, Yarrow> mem: <memory> io: <I/O> VESA: information block 56 45 53 41 00 02 00 01 00 01 00 00 00 00 22 00 00 01 40 00 00 01 0b 01 00 01 21 01 00 01 2a 01 00 01 00 01 01 01 10 01 11 01 12 01 03 01 13 01 14 01 15 01 05 01 16 01 17 01 18 01 07 01 19 01 VESA: 40 mode(s) found VESA: v2.0, 4096k memory, flags:0x0, mode table:0xc06f6302 (1000022) VESA: ATI MACH64 VESA: ATI Technologies Inc. MACH64RM 01.00 acpi0: <FUJ IRIS> on motherboard acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x80003904 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=71908086) pcibios: BIOS version 2.10 Found $PIR table, 7 entries at 0xc00fdf50 PCI-Only Interrupts: none Location Bus Device Pin Link IRQs embedded 0 7 D 0x63 9 10 11 embedded 0 4 A 0x60 10 11 embedded 0 8 A 0x62 5 7 9 10 slot 1 0 16 A 0x61 9 slot 2 0 17 A 0x63 9 embedded 0 1 A 0x61 9 10 11 embedded 1 0 A 0x61 9 10 11 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 7 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 4 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 4 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 4 func 1 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 16 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 17 func 0 acpi0: Power Button (fixed) acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 0 func 0 acpi_ec0: <Embedded Controller: GPE 0x9> port 0x66,0x62 on acpi0 acpi_ec0: info: new max delay is 180 us acpi_ec0: info: new max delay is 260 us ACPI timer looks BAD min = 2, max = 7, width = 5 ACPI timer looks BAD min = 2, max = 7, width = 5 ACPI timer looks BAD min = 2, max = 7, width = 5 ACPI timer looks BAD min = 2, max = 6, width = 4 ACPI timer looks BAD min = 2, max = 6, width = 4 ACPI timer looks BAD min = 2, max = 6, width = 4 ACPI timer looks BAD min = 2, max = 7, width = 5 ACPI timer looks BAD min = 2, max = 7, width = 5 ACPI timer looks BAD min = 2, max = 6, width = 4 ACPI timer looks BAD min = 2, max = 7, width = 5 Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 cpu0: <ACPI CPU (3 Cx states)> on acpi0 acpi_lid0: <Control Method Lid Switch> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 ACPI PCI link initial configuration: \\_SB_.LNKD irq 0: [ 5 9 10 11] 9+ low,level,sharable 0.7.3 \\_SB_.LNKA irq 0: [ 5 9 10 11] 11+ low,level,sharable 0.4.0 \\_SB_.LNKB irq 0: [ 5 9 10 11] 9+ low,level,sharable 0.4.1 \\_SB_.LNKC irq 0: [ 5 9 10 11] 5+ low,level,sharable 0.8.0 \\_SB_.LNKB irq 0: [ 5 9 10 11] 9+ low,level,sharable 0.16.0 \\_SB_.LNKD irq 0: [ 5 9 10 11] 9+ low,level,sharable 0.17.0 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 map[10]: type 3, range 32, base e0000000, size 26, enabled found-> vendor=0x8086, dev=0x7190, revid=0x03 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x2210, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x7191, revid=0x03 bus=0, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x001f, statreg=0x0220, cachelnsz=0 (dwords) lattimer=0x80 (3840 ns), mingnt=0x8c (35000 ns), maxlat=0x00 (0 ns) map[10]: type 1, range 32, base 00000000, size 12, enabled found-> vendor=0x104c, dev=0xac51, revid=0x00 bus=0, slot=4, func=0 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns) intpin=a, irq=255 powerspec 1 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base 00000000, size 12, enabled found-> vendor=0x104c, dev=0xac51, revid=0x00 bus=0, slot=4, func=1 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns) intpin=a, irq=255 powerspec 1 supports D0 D1 D2 D3 current D0 found-> vendor=0x8086, dev=0x7110, revid=0x02 bus=0, slot=7, func=0 class=06-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 00001080, size 4, enabled found-> vendor=0x8086, dev=0x7111, revid=0x01 bus=0, slot=7, func=1 class=01-01-80, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 000010a0, size 5, port disabled pcib0: matched entry for 0.7.INTD (src \\_SB_.LNKD) pcib0: possible interrupts: 5 9 10 11 ACPI PCI link arbitrated settings: \\_SB_.LNKD (references 2, priority 175): interrupts: 11 10 5 9 penalty: 60 60 110 120 \\_SB_.LNKB (references 2, priority 175): interrupts: 11 10 5 9 penalty: 60 60 110 120 \\_SB_.LNKA (references 1, priority 87): interrupts: 11 10 5 9 penalty: 60 60 110 120 \\_SB_.LNKC (references 1, priority 87): interrupts: 11 10 5 9 penalty: 60 60 110 120 pcib0: slot 7 INTD routed to irq 9 via \\_SB_.LNKD found-> vendor=0x8086, dev=0x7112, revid=0x01 bus=0, slot=7, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=9 map[90]: type 4, range 32, base 0000ff80, size 4, enabled found-> vendor=0x8086, dev=0x7113, revid=0x03 bus=0, slot=7, func=3 class=06-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0003, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 1, range 32, base fc101000, size 12, enabled map[14]: type 1, range 32, base fc110000, size 16, enabled pcib0: matched entry for 0.8.INTA (src \\_SB_.LNKC) pcib0: possible interrupts: 5 9 10 11 ACPI PCI link arbitrated settings: \\_SB_.LNKB (references 2, priority 335): interrupts: 11 10 5 9 penalty: 120 120 170 260 \\_SB_.LNKA (references 1, priority 167): interrupts: 11 10 5 9 penalty: 120 120 170 260 \\_SB_.LNKC (references 1, priority 167): interrupts: 11 10 5 9 penalty: 120 120 170 260 pcib0: slot 8 INTA routed to irq 5 via \\_SB_.LNKC found-> vendor=0x1013, dev=0x6005, revid=0x01 bus=0, slot=8, func=0 class=04-01-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x04 (1000 ns), maxlat=0x18 (6000 ns) intpin=a, irq=5 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base fc100000, size 12, enabled map[14]: type 4, range 32, base 00001040, size 6, enabled map[18]: type 1, range 32, base fc000000, size 20, enabled pcib0: matched entry for 0.16.INTA (src \\_SB_.LNKB) pcib0: possible interrupts: 5 9 10 11 ACPI PCI link arbitrated settings: \\_SB_.LNKB (references 2, priority 490): interrupts: 11 10 5 9 penalty: 180 180 240 380 \\_SB_.LNKA (references 1, priority 245): interrupts: 11 10 5 9 penalty: 180 180 240 380 pcib0: slot 16 INTA routed to irq 9 via \\_SB_.LNKB found-> vendor=0x8086, dev=0x1229, revid=0x08 bus=0, slot=16, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0013, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns) intpin=a, irq=9 powerspec 2 supports D0 D1 D2 D3 current D0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0x2000-0x2fff pcib1: memory decode 0xfc200000-0xfdffffff pcib1: prefetched decode 0xfff00000-0xfffff ACPI PCI link initial configuration: \\_SB_.LNKB irq* 9: [ 5 9 10 11] 9+ low,level,sharable 1.0.0 pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 map[10]: type 1, range 32, base fd000000, size 24, enabled pcib1: device (null) requested decoded memory range 0xfd000000-0xfdffffff map[14]: type 4, range 32, base 00002000, size 8, enabled pcib1: device (null) requested decoded I/O range 0x2000-0x20ff map[18]: type 1, range 32, base fc200000, size 12, enabled pcib1: device (null) requested decoded memory range 0xfc200000-0xfc200fff pcib1: matched entry for 1.0.INTA (src \\_SB_.LNKB) pcib1: slot 0 INTA is already routed to irq 9 found-> vendor=0x1002, dev=0x4c4d, revid=0x64 bus=1, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=9 powerspec 1 supports D0 D1 D2 D3 current D0 pci1: <display, VGA> at device 0.0 (no driver attached) pci0: <bridge, PCI-CardBus> at device 4.0 (no driver attached) pci0: <bridge, PCI-CardBus> at device 4.1 (no driver attached) PCI-ISA bridge with incorrect subclass 0x80 PCI-ISA bridge with incorrect subclass 0x80 isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 UDMA33 controller> port 0x1080-0x108f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1080 ata0: channel #0 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00 ata0-slave: stat=0x00 err=0x01 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER> ata0: [MPSAFE] ata1: channel #1 on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=03 ostat0=50 ostat1=01 ata1-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb ata1-slave: stat=0x01 err=0x04 lsb=0x00 msb=0x00 ata1: reset tp2 stat0=00 stat1=01 devices=0x4<ATAPI_MASTER> ata1: [MPSAFE] pci0: <serial bus, USB> at device 7.2 (no driver attached) intpm0: <Intel 82371AB Power management controller> port 0xff80-0xff8f irq 9 at device 7.3 on pci0 intpm0: Reserved 0x10 bytes for rid 0x90 type 4 at 0xff80 intpm0: I/O mapped ff80 intpm0: intr IRQ 9 enabled revision 0 intpm0: [GIANT-LOCKED] intsmb0: <Intel PIIX4 SMBUS Interface> on intpm0 smbus0: <System Management Bus> on intsmb0 intpm0: PM I/O mapped 1000 pcm0: <Crystal Semiconductor CS4281> mem 0xfc110000-0xfc11ffff,0xfc101000-0xfc101fff irq 5 at device 8.0 on pci0 pcm0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfc101000 pcm0: Reserved 0x10000 bytes for rid 0x14 type 3 at 0xfc110000 pcm0: [GIANT-LOCKED] pcm0: <Cirrus Logic CS4297A AC97 Codec (id = 0x43525914)> pcm0: Codec features headphone, 20 bit DAC, 18 bit ADC, 6 bit master volume, Crystal Semi 3D Stereo Enhancement pcm0: Primary codec extended features AMAP pcm0: sndbuf_setmap bac4000, 4000; 0xca2d6000 -> bac4000 pcm0: sndbuf_setmap bac0000, 4000; 0xca2da000 -> bac0000 fxp0: <Intel 82559 Pro/100 Ethernet> port 0x1040-0x107f mem 0xfc000000-0xfc0fffff,0xfc100000-0xfc100fff irq 9 at device 16.0 on pci0 fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfc100000 fxp0: using memory space register mapping fxp0: PCI IDs: 8086 1229 10cf 108e 0008 fxp0: Dynamic Standby mode is disabled miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: bpf attached fxp0: Ethernet address: 00:d0:59:01:ed:22 fxp0: [MPSAFE] unknown: not probed (disabled) speaker0 port 0x61 on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 atkbd0: [GIANT-LOCKED] psm0: unable to allocate IRQ psmcpnp0 irq 12 on acpi0 psm0: current command byte:0047 psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model GlidePoint, device ID 0-00, 2 buttons psm0: config:00000000, flags:00000008, packet size:3 psm0: syncmask:c0, syncbits:00 acpi_acad0: <AC Adapter> on acpi0 acpi_cmbat0: <Control Method Battery> on acpi0 unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) unknown: not probed (disabled) npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it Trying Read_Port at 203 Trying Read_Port at 243 Trying Read_Port at 283 Trying Read_Port at 2c3 Trying Read_Port at 303 Trying Read_Port at 343 Trying Read_Port at 383 Trying Read_Port at 3c3 sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <ISA Option ROM> at iomem 0xc0000-0xcffff on isa0 pmtimer0 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fdc0 failed to probe at port 0x3f0 irq 6 drq 2 on isa0 fe0: not probed (disabled) ie0: not probed (disabled) lnc0: not probed (disabled) pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0 pcic1: not probed (disabled) ppc0 failed to probe at irq 7 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio0 failed to probe at port 0x3f8 irq 4 flags 0x10 on isa0 sio1 failed to probe at port 0x2f8 irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 fb0 at vga0 fb0: vga0, vga, type:VGA (5), flags:0x700ff fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000 fb0: init mode:24, bios mode:3, current mode:24 fb0: window:0xc00b8000 size:32k gran:32k, buf:0 size:32k vga0: vga: WARNING: video mode switching is not fully supported on this adapter VGA parameters upon power-up 50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 52 83 b4 1f 00 4f 0d 0e 00 00 07 80 91 87 8f 28 1f 8f b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff VGA parameters in BIOS for mode 24 50 18 10 00 10 00 03 00 02 67 5f 4f 50 82 55 81 bf 1f 00 4f 0d 0e 00 00 00 00 9c 8e 8f 28 1f 96 b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff EGA/VGA parameters to be used for mode 24 50 18 10 00 00 00 03 00 02 e7 73 4f 4f 97 52 83 b4 1f 00 4f 0d 0e 00 00 07 80 91 87 8f 28 1f 8f b5 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c 3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. Timecounter "TSC" frequency 497559801 Hz quality 800 Timecounters tick every 1.000 msec lo0: bpf attached cpu0: set speed to 100.0% acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% acpi_acad0: acline initialization start acpi_acad0: On Line acpi_acad0: acline initialization done, tried 1 times acpi_cmbat0: battery initialization start ata0-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin ata0-master: setting PIO4 on Intel PIIX4 chip ata0-master: setting UDMA33 on Intel PIIX4 chip ad0: <TOSHIBA MK4025GAS/KA100A> ATA-6 disk at ata0-master ad0: 38154MB (78140160 sectors), 77520 C, 16 H, 63 S, 512 B ad0: 16 secs/int, 1 depth queue, UDMA33 GEOM: new disk ad0 ata1-master: pio=0x0c wdma=0x22 udma=0x42 cable=40pin ata1-master: setting PIO4 on Intel PIIX4 chip ata1-master: setting UDMA33 on Intel PIIX4 chip acd0: <CD-224E/1.7A> CDROM drive at ata1 as master acd0: read 4134KB/s (4134KB/s), 128KB buffer, UDMA33 acd0: Reads: CDR, CDRW, CDDA stream, packet acd0: Writes: acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc [0] f:80 typ:165 s(CHS):0/1/1 e(CHS):1023/254/63 s:63 l:78140097 [1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 [3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0 GEOM: Configure ad0s1, start 32256 length 40007729664 end 40007761919 GEOM: Configure ad0s1a, start 0 length 268435456 end 268435455 GEOM: Configure ad0s1b, start 268435456 length 376217600 end 644653055 GEOM: Configure ad0s1c, start 0 length 40007729664 end 40007729663 GEOM: Configure ad0s1d, start 644653056 length 1073741824 end 1718394879 GEOM: Configure ad0s1e, start 1718394880 length 268435456 end 1986830335 GEOM: Configure ad0s1f, start 1986830336 length 38020899328 end 40007729663 Mounting root from ufs:/dev/ad0s1a start_init: trying /sbin/init pci0: driver added found-> vendor=0x104c, dev=0xac51, revid=0x00 bus=0, slot=4, func=0 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns) intpin=a, irq=255 powerspec 1 supports D0 D1 D2 D3 current D0 pci0:4:0: reprobing on driver added found-> vendor=0x104c, dev=0xac51, revid=0x00 bus=0, slot=4, func=1 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns) intpin=a, irq=255 powerspec 1 supports D0 D1 D2 D3 current D0 pci0:4:1: reprobing on driver added found-> vendor=0x8086, dev=0x7112, revid=0x01 bus=0, slot=7, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=9 pci0:7:2: reprobing on driver added uhci0: <Intel 82371AB/EB (PIIX4) USB controller> port 0x10a0-0x10bf irq 9 at device 7.2 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x10a0 uhci0: [GIANT-LOCKED] usb0: <Intel 82371AB/EB (PIIX4) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered pci1: driver added found-> vendor=0x1002, dev=0x4c4d, revid=0x64 bus=1, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=9 powerspec 1 supports D0 D1 D2 D3 current D0 pci1:0:0: reprobing on driver added pci0: driver added found-> vendor=0x104c, dev=0xac51, revid=0x00 bus=0, slot=4, func=0 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns) intpin=a, irq=255 powerspec 1 supports D0 D1 D2 D3 current D0 pci0:4:0: reprobing on driver added found-> vendor=0x104c, dev=0xac51, revid=0x00 bus=0, slot=4, func=1 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns) intpin=a, irq=255 powerspec 1 supports D0 D1 D2 D3 current D0 pci0:4:1: reprobing on driver added pci1: driver added found-> vendor=0x1002, dev=0x4c4d, revid=0x64 bus=1, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=9 powerspec 1 supports D0 D1 D2 D3 current D0 pci1:0:0: reprobing on driver added pci0: driver added found-> vendor=0x104c, dev=0xac51, revid=0x00 bus=0, slot=4, func=0 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns) intpin=a, irq=255 powerspec 1 supports D0 D1 D2 D3 current D0 pci0:4:0: reprobing on driver added found-> vendor=0x104c, dev=0xac51, revid=0x00 bus=0, slot=4, func=1 class=06-07-00, hdrtype=0x02, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=8 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x03 (750 ns) intpin=a, irq=255 powerspec 1 supports D0 D1 D2 D3 current D0 pci0:4:1: reprobing on driver added pci1: driver added found-> vendor=0x1002, dev=0x4c4d, revid=0x64 bus=1, slot=0, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0087, statreg=0x0290, cachelnsz=8 (dwords) lattimer=0x42 (1980 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=9 powerspec 1 supports D0 D1 D2 D3 current D0 pci1:0:0: reprobing on driver added splash: image decoder found: blank_saver Linux ELF exec handler installed acpi_cmbat0: battery initialization failed, giving up kernel config: # # For more information on this file, please read the handbook section on # Kernel Configuration Files: # # http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html # # The handbook is also available locally in /usr/share/doc/handbook # if you've installed the doc distribution, otherwise always see the # FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the # latest information. # # An exhaustive list of options and more detailed explanations of the # device lines is also present in the ../../conf/NOTES and NOTES files. # If you are in doubt as to the purpose or necessity of a line, check first # in NOTES. # makeoptions DEBUG=-g machine i386 cpu I686_CPU options CPU_FASTER_5X86_FPU ident RENE_2004-09-05d device apic options SCHED_ULE options KDB options DDB options GDB # remote GDB support options WITNESS options WITNESS_SKIPSPIN options WITNESS_KDB options INVARIANTS options INVARIANT_SUPPORT options AHC_REG_PRETTY_PRINT options AHD_REG_PRETTY_PRINT options ADAPTIVE_GIANT options INET #InterNETworking, mandatory options INET6 #IPv6 communications protocols #options IPSEC #options IPSEC_ESP options FFS #Berkeley Fast Filesystem options SOFTUPDATES #Enable FFS soft updates support options UFS_ACL #Support for access control lists options UFS_DIRHASH #Improve performance on big directories options COMPAT_FREEBSD4 #Compatible with FreeBSD4 options COMPAT_43 #Compatible with BSD 4.3 [KEEP THIS!] options KTRACE options PQ_CACHESIZE=32 #32kB L2 Cache options _KPOSIX_PRIORITY_SCHEDULING #Posix P1003_1B real-time extensions device isa device pci # ATA and ATAPI devices device ata device atadisk # ATA disk drives device atapicd # ATAPI CDROM drives # atkbdc0 controls both the keyboard and the PS/2 mouse device atkbdc # AT keyboard controller device atkbd options KBD_INSTALL_CDEV device psm # PS/2 mouse # syscons is the default console driver, resembling an SCO console device sc options SC_TWOBUTTON_MOUSE device vga # VGA video card driver options FB_INSTALL_CDEV device npx # Floating point support - do not disable. options DEVICE_POLLING # improve fxp0 performance options HZ=1000 # for DEVICE_POLLING, interrrupt rate device loop # Network loopback device ether # Ethernet support device pty # Pseudo-ttys (telnet,xterm etc) device bpf # needed for DHCP options XBONEHACK # same address pairs over multiple gif intf options PPP_BSDCOMP options PPP_DEFLATE options PPP_FILTER device splash #screensaver/splash screen device pmtimer kldstat: Id Refs Address Size Name 1 28 0xc0400000 2f1cd8 kernel 2 1 0xc06f2000 547c vesa.ko 3 1 0xc06f8000 a83c if_fxp.ko 4 2 0xc0703000 1aa04 miibus.ko 5 1 0xc071e000 597c snd_cs4281.ko 6 2 0xc0724000 21600 sound.ko 7 1 0xc0746000 c280 random.ko 8 1 0xc0753000 3084 speaker.ko 9 1 0xc0757000 2b4c mem.ko 10 1 0xc075a000 1cec io.ko 11 1 0xc075c000 450c intpm.ko 12 2 0xc0761000 3724 smbus.ko 13 1 0xc0765000 1e6c cd9660_iconv.ko 14 5 0xc0767000 4bdc libiconv.ko 15 2 0xc076c000 a64c cd9660.ko 16 1 0xc0777000 1e80 msdosfs_iconv.ko 17 2 0xc0779000 10b00 msdosfs.ko 18 14 0xc078a000 5e764 acpi.ko 19 1 0xc1265000 26000 usb.ko 20 1 0xc12ab000 2000 blank_saver.ko 21 1 0xc12c0000 1b000 linux.ko 22 1 0xc12db000 4000 sysvmsg.ko 23 1 0xc12e6000 5000 sysvsem.ko 24 1 0xc12f8000 4000 sysvshm.ko Rene
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:16 UTC