Am Dienstag, 31. August 2004 23:49 schrieb Kenneth Stailey: > I'm trying to upgrade a TYAN Tiger K8WS S2875S from FreeBSD-5.2.1-p8 to > 5.3-BETA1-20040823. > > It fails because instead of seeing the SiI3114 as ar0 (RAID-1) it sees two > separate disks: I also reported this problem several times for the sil0680 and cmd0649 chips on this list. I recently opened a PR (kern/71355). Until this isn't fixed you cannot upgrade to 5.3-x -Harry > > ad4: 194481MB <Maxtor 6Y200M0/YAR51HW0> [395136/16/63] at ata2-master > SATA150 ad6: 194481MB <Maxtor 6Y200M0/YAR51HW0> [395136/16/63] at > ata3-master SATA150 > > I don't think I should upgrade just one half of the mirror so I abort the > upgrade. > > When booting 5.2.1-p8 > > GEOM: create disk ad4 dp=0xffffff003b2f6aa0 > ad4: 194481MB <Maxtor 6Y200M0> [395136/16/63] at ata2-master UDMA100 > GEOM: create disk ad6 dp=0xffffff003b2f62a0 > ad6: 194481MB <Maxtor 6Y200M0> [395136/16/63] at ata3-master UDMA100 > GEOM: create disk ar0 dp=0xffffff0000d7fa70 > ar0: 194480MB <ATA RAID1 array> [24792/255/63] status: READY subdisks: > disk0 READY on ad4 at ata2-master > disk1 READY on ad6 at ata3-master > Mounting root from ufs:/dev/ar0s1a > > When booting 5.3-BETA1 > > Copyright (c) 1992-2004 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.3-BETA1-20040823 #0: Mon Aug 23 11:03:37 UTC 2004 > root_at_quynh.NUXI.org:/usr/obj/usr/src/sys/GENERIC > WARNING: WITNESS option enabled, expect reduced performance. > ACPI APIC Table: <A M I OEMAPIC > > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: AMD Opteron(tm) Processor 246 (1993.31-MHz K8-class CPU) > Origin = "AuthenticAMD" Id = 0xf58 Stepping = 8 > > Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA >,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2> AMD > Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow> > real memory = 1073676288 (1023 MB) > avail memory = 1020493824 (973 MB) > MADT: Forcing active-low polarity and level trigger for SCI > ioapic0 <Version 1.1> irqs 0-23 on motherboard > acpi0: <A M I OEMXSDT> on motherboard > acpi0: Power Button (fixed) > Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 > acpi_timer0: <24-bit timer at 3.579545MHz> port 0x5008-0x500b on acpi0 > cpu0: <ACPI CPU> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pci2: <ACPI PCI bus> on pcib1 > pci2: <display, VGA> at device 0.0 (no driver attached) > pci2: <display> at device 0.1 (no driver attached) > pcib2: <ACPI PCI-PCI bridge> at device 6.0 on pci0 > pci1: <ACPI PCI bus> on pcib2 > ohci0: <OHCI (generic) USB controller> mem 0xff4fc000-0xff4fcfff irq 19 at > device 0.0 on pci1 > ohci0: [GIANT-LOCKED] > usb0: OHCI version 1.0, legacy support > usb0: SMM does not respond, resetting > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 3 ports with 3 removable, self powered > ohci1: <OHCI (generic) USB controller> mem 0xff4fd000-0xff4fdfff irq 19 at > device 0.1 on pci1 > ohci1: [GIANT-LOCKED] > usb1: OHCI version 1.0, legacy support > usb1: SMM does not respond, resetting > usb1: <OHCI (generic) USB controller> on ohci1 > usb1: USB revision 1.0 > uhub1: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 3 ports with 3 removable, self powered > em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.25> port > 0x8880-0x88bf mem 0xff4a0000-0xff4bffff,0xff4c0000-0xff4dffff irq 18 at > device 3.0 on pci1 > em0: [GIANT-LOCKED] > em0: Ethernet address: 00:e0:81:28:99:c4 > em0: Speed:N/A Duplex:N/A > atapci0: <SiI 3114 SATA150 controller> port > 0x9400-0x940f,0x9480-0x9483,0x9800-0x9807,0x9880-0x9883,0x9c00-0x9c07 mem > 0xff4ffc00-0xff4fffff irq 19 at device 5.0 on pci1 > ata2: channel #0 on atapci0 > ata3: channel #1 on atapci0 > ata4: channel #2 on atapci0 > ata5: channel #3 on atapci0 > fwohci0: <VIA Fire II (VT6306)> port 0x8c00-0x8c7f mem > 0xff4ff000-0xff4ff7ff irq 17 at device 10.0 on pci1 > fwohci0: [GIANT-LOCKED] > fwohci0: OHCI version 1.0 (ROM=1) > fwohci0: No. of Isochronous channels is 4. > fwohci0: EUI64 00:e0:81:00:00:30:12:53 > fwohci0: Phy 1394a available S400, 2 ports. > fwohci0: Link S400, max_rec 2048 bytes. > firewire0: <IEEE1394(FireWire) bus> on fwohci0 > fwe0: <Ethernet over FireWire> on firewire0 > if_fwe0: Fake Ethernet address: 02:e0:81:30:12:53 > fwe0: Ethernet address: 02:e0:81:30:12:53 > sbp0: <SBP-2/SCSI over FireWire> on firewire0 > fwohci0: Initiate bus reset > fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode > firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) > firewire0: bus manager 0 (me) > uhci0: <VIA 83C572 USB controller> port 0x9000-0x901f irq 17 at device 11.0 > on pci1 > uhci0: [GIANT-LOCKED] > usb2: <VIA 83C572 USB controller> on uhci0 > usb2: USB revision 1.0 > uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub2: 2 ports with 2 removable, self powered > uhci1: <VIA 83C572 USB controller> port 0x9080-0x909f irq 18 at device 11.1 > on pci1 > uhci1: [GIANT-LOCKED] > usb3: <VIA 83C572 USB controller> on uhci1 > usb3: USB revision 1.0 > uhub3: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub3: 2 ports with 2 removable, self powered > pci1: <serial bus, USB> at device 11.2 (no driver attached) > isab0: <PCI-ISA bridge> at device 7.0 on pci0 > isa0: <ISA bus> on isab0 > atapci1: <AMD 8111 UDMA133 controller> port > 0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0 > ata0: channel #0 on atapci1 > ata1: channel #1 on atapci1 > pci0: <serial bus, SMBus> at device 7.2 (no driver attached) > pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached) > pci0: <multimedia, audio> at device 7.5 (no driver attached) > acpi_button0: <Power Button> on acpi0 > atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 > atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: [GIANT-LOCKED] > psm0: model IntelliMouse, device ID 3 > sio0: configured irq 4 not in bitmap of probed irqs 0 > sio0: port may not be enabled > sio0 port 0x3f8-0x3ff irq 4 on acpi0 > sio0: type 16550A > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > sio1 port 0x2f8-0x2ff irq 3 on acpi0 > sio1: type 16550A > fdc0: <floppy drive controller (FDE)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on > acpi0 > fdc0: FIFO enabled, 8 bytes threshold > fd0: <1440-KB 3.5" drive> on fdc0 drive 0 > ppc0 port 0x378-0x37f irq 7 on acpi0 > ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode > ppbus0: <Parallel port bus> on ppc0 > plip0: <PLIP network interface> on ppbus0 > lpt0: <Printer> on ppbus0 > lpt0: Interrupt-driven port > ppi0: <Parallel I/O> on ppbus0 > orm0: <ISA Option ROMs> at iomem 0xcb000-0xcf7ff,0xc0000-0xcafff on isa0 > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounter "TSC" frequency 1993314155 Hz quality 800 > Timecounters tick every 0.976 msec > md0: Preloaded image </boot/mfsroot> 4194304 bytes at 0xffffffff808e5db0 > acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0% > ATAPI_RESET time = 40us > acd0: CDRW <SONY CD-RW CRX230ED/4YS1> at ata0-master UDMA33 > ad4: 194481MB <Maxtor 6Y200M0/YAR51HW0> [395136/16/63] at ata2-master > SATA150 ad6: 194481MB <Maxtor 6Y200M0/YAR51HW0> [395136/16/63] at > ata3-master SATA150 Mounting root from ufs:/dev/md0 > em0: Link is up 100 Mbps Full Duplex > > Thanks for any advice as how to upgrade this system. > > _______________________________________________ > freebsd-current_at_freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:10 UTC