Re: usb hub disconnect crashes 5.3-BETA4 hard

On Thu, 2004-09-16 at 17:46, David Gilbert wrote:
> I have two different USB mice.  One is a little portable one that has
> a wireless "dongle" that pluggs into the port.  This one works fine.
> 
> The second is an MX-900 (Logitec) that is a "bluetooth" mouse... but
> the unit itself shows up as a USB hub and a usb mouse in that hub.
> This (I believe) is due to the fact that the "base station" is
> emulating a usb mouse ... but also has the ability to show up as a
> bluetooth receiver (if you enable it).  That function is not enabled
> on my mouse --- so it shows up as hub with a mouse attached to the
> hub.
> 
> When the hub/mouse is unplugged, FreeBSD-5.3-BETA4 panic's hard but
> BETA2 did not.  This may be a false hope ... I think I have seen this
> before, but I don't remember exactly.
> 
> When it panics hard, I see "ums0 detached" (bright text) followed by
> "(null) at uhub4 <something something>" followed by a panic message an
> no dump.
> 
> Here is the kernel messages for the working mouse:
> 
> [3:2:302]dgilbert_at_canoe:~> dmesg | grep -i usb
> uhci0: <Intel 82801DB (ICH4) USB controller USB-A> port 0xbf80-0xbf9f irq 11 at device 29.0 on pci0
> usb0: <Intel 82801DB (ICH4) USB controller USB-A> on uhci0
> usb0: USB revision 1.0
> uhci1: <Intel 82801DB (ICH4) USB controller USB-B> port 0xbf40-0xbf5f irq 11 at device 29.1 on pci0
> usb1: <Intel 82801DB (ICH4) USB controller USB-B> on uhci1
> usb1: USB revision 1.0
> uhci2: <Intel 82801DB (ICH4) USB controller USB-C> port 0xbf20-0xbf3f irq 11 at device 29.2 on pci0
> usb2: <Intel 82801DB (ICH4) USB controller USB-C> on uhci2
> usb2: USB revision 1.0
> ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf4fffc00-0xf4ffffff irq 11 at device 29.7 on pci0
> ehci_pci_attach: companion usb0
> ehci_pci_attach: companion usb1
> ehci_pci_attach: companion usb2
> usb3: EHCI version 1.0
> usb3: companion controllers, 2 ports each: usb0 usb1 usb2
> usb3: <EHCI (generic) USB 2.0 controller> on ehci0
> usb3: USB revision 2.0
> ums0: PATEN USB Receiver, rev 1.10/1.03, addr 2, iclass 3/1
> ums0: PATEN USB Receiver, rev 1.10/1.03, addr 2, iclass 3/1
> 
> Here are the kernel messages for the mouse attaching (obviously I
> can't show the exact detatch messages):
> 
> uhub4: Texas Instruments General Purpose USB Hub, class 9/0, rev 1.10/1.01, addr 3
> uhub4: 2 ports with 0 removable, bus powered
> ums1: Logitech USB Receiver, rev 1.10/27.04, addr 4, iclass 3/1
> ums1: 7 buttons and Z dir.
> 
> Dave.
I was able to lay with this situation a little bit more and discovered
that plugging and unplugging USB 2.0/1.1 hub with no devices or
USB-to-serial adapter does not cause a crash. However, if I unplug USB
docking station which has 4-port USB 1.0 hub, ums, ukbd, ubsa and ulpt
crashes system reliably. I am running 6.0-current with the exception of
psm.c rolled back to 1.70 because of Synaptic support. I load usb stack
as modules, and to reproduce crash 'usb.ko' is sufficient.

I have been able to produce a dump and poke around it with gdb, but I do
not have enough expertise to glean much, apart from the fact that it
happens when bus deletes a child.

I have attached output of dmesg, kldstat -v, usbdevs -v, pciconf -l -v
and gdb examining crash dump. Dump itself is 600MB+, so if someone needs
it we can see what could be done.

If there are patches to test or things to try, I will be glad to oblige.

---
Alexandre "Sunny" Kovalenko.