At 11:12 AM 08/08/2005, Poul-Henning Kamp wrote: >I belive there is a bug in the HiFn chips that makes them do a soft reset >under some set of circumstances which we have never been able to nail >down. Actually, I think this is something different. I know the issue you are referring to, and it seems to happen on many (but not all) motherboards. Note, this problem does not happen in UP mode on this box, only on SMP. Also, I just booted RELENG_4_11 on the box and installed an SMP kernel. hippo# hifnstats input 7648447680 bytes 2338053 packets output 7648431264 bytes 2338052 packets invalid 0 nomem 0 abort 0 noirq 1263291 unaligned 0 totbatch 0 maxbatch 0 nomem: map 0 load 0 mbuf 0 mcl 0 cr 0 sd 0 hippo# I am able to run /usr/bin/openssl aes-128-cbc -in big -k pass | ssh -c aes128-cbc mdtancsa_at_127.0.0.1 "cat - > /dev/null" until the cows come home without issue, even with an SMP kernel built. So it seems like its something with this box and RELENG_6 that causes the box to totally lock up Here is the same hardware on RELENG_4 hippo# dmesg Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 4.11-RELEASE #0: Mon Aug 8 15:43:47 EDT 2005 root_at_hippo.netperf.freebsd.org:/usr/obj/usr/src/sys/smp Timecounter "i8254" frequency 1193182 Hz CPU: Pentium III/Pentium III Xeon/Celeron (500.02-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x672 Stepping = 2 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 2147475456 (2097144K bytes) config> q avail memory = 2086166528 (2037272K bytes) Changing APIC ID for IO APIC #0 from 0 to 4 on chip Programming 24 pins in IOAPIC #0 IOAPIC #0 intpin 2 -> irq 0 FreeBSD/SMP: Multiprocessor motherboard: 4 CPUs cpu0 (BSP): apic id: 3, version: 0x00040011, at 0xfee00000 cpu1 (AP): apic id: 0, version: 0x00040011, at 0xfee00000 cpu2 (AP): apic id: 1, version: 0x00040011, at 0xfee00000 cpu3 (AP): apic id: 2, version: 0x00040011, at 0xfee00000 io0 (APIC): apic id: 4, version: 0x00170011, at 0xfec00000 Preloaded elf kernel "kernel" at 0xc056a000. Preloaded userconfig_script "/boot/kernel.conf" at 0xc056a09c. Pentium Pro MTRR support enabled md0: Malloc disk Using $PIR table, 11 entries at 0xc00fc7a0 npx0: <math processor> on motherboard npx0: INT 16 interface pcib0: <Intel 82454NX PXB#0, Bus#A> on motherboard IOAPIC #0 intpin 14 -> irq 2 pci0: <PCI bus> on pcib0 isab0: <Intel 82371AB PCI to ISA bridge> at device 2.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 ATA33 controller> at device 2.1 on pci0 atapci0: ATA channel disabled by BIOS uhci0: <Intel 82371AB/EB (PIIX4) USB controller> irq 0 at device 2.2 on pci0 uhci0: Could not map ports device_probe_and_attach: uhci0 attach returned 6 Timecounter "PIIX" frequency 3579545 Hz chip0: <Intel 82371AB Power management controller> port 0x850-0x85f at device 2.3 on pci0 pci0: <ATI Mach64-GI graphics accelerator> at 4.0 pcib1: <PCI to PCI bridge (vendor=8086 device=0960)> at device 8.0 on pci0 pci1: <PCI bus> on pcib1 amr0: <LSILogic MegaRAID> mem 0xfe000000-0xfe3fffff irq 2 at device 8.1 on pci0 amr0: <Series 466> Firmware GH6D, BIOS 1.43, 32MB RAM pcib4: <Intel 82454NX PCI Expander Bridge> at device 18.0 on pci0 pcib5: <Intel 82454NX PCI Expander Bridge> at device 19.0 on pci0 pcib6: <Intel 82454NX PCI Expander Bridge> at device 20.0 on pci0 pcib2: <Intel 82454NX PXB#0, Bus#B> on motherboard IOAPIC #0 intpin 21 -> irq 5 IOAPIC #0 intpin 22 -> irq 10 IOAPIC #0 intpin 20 -> irq 11 pci2: <PCI bus> on pcib2 ahc0: <Adaptec aic7890/91 Ultra2 SCSI adapter> port 0xec00-0xecff mem 0xfe902000-0xfe902fff irq 5 at device 4.0 on pci2 aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs ahc1: <Adaptec aic7890/91 Ultra2 SCSI adapter> port 0xe800-0xe8ff mem 0xfe901000-0xfe901fff irq 10 at device 6.0 on pci2 aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs ahc2: <Adaptec aic7860 Ultra SCSI adapter> port 0xe400-0xe4ff mem 0xfe900000-0xfe900fff irq 11 at device 8.0 on pci2 aic7860: Ultra Single Channel A, SCSI Id=7, 3/253 SCBs pcib3: <Intel 82454NX PXB#1, Bus#A> on motherboard IOAPIC #0 intpin 19 -> irq 12 IOAPIC #0 intpin 18 -> irq 13 pci3: <PCI bus> on pcib3 em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.42> port 0xfcc0-0xfcff mem 0xfeb00000-0xfeb1ffff,0xfeb20000-0xfeb3ffff irq 12 at device 1.0 on pci3 em0: Speed:N/A Duplex:N/A hifn0 mem 0xfeb40000-0xfeb47fff,0xfeb48000-0xfeb49fff,0xfeb4a000-0xfeb4afff irq 13 at device 3.0 on pci3 hifn0: Hifn 7955, rev 0, 32KB dram orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff,0xd0000-0xd07ff,0xd4000-0xd47ff,0xd8000-0xd87ff on isa0 pmtimer0 on isa0 fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: FIFO enabled, 8 bytes threshold fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0 ata1 at port 0x170-0x177,0x376 irq 15 on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 kbd0 at atkbd0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x100> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 16550A, console sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0 ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 APIC_IO: Testing 8254 interrupt delivery APIC_IO: routing 8254 via IOAPIC #0 intpin 2 Waiting 15 seconds for SCSI devices to settle amrd0: <LSILogic MegaRAID logical drive> on amr0 amrd0: 17366MB (35565568 sectors) RAID 1 (optimal) SMP: AP CPU #3 Launched! SMP: AP CPU #1 Launched! SMP: AP CPU #2 Launched! pass0 at amr0 bus 0 target 6 lun 0 pass0: <DELL 1x3 U2W SCSI BP 5.12> Fixed Processor SCSI-2 device Mounting root from ufs:/dev/amrd0s1a cd0 at ahc2 bus 0 target 5 lun 0 cd0: <NEC CD-ROM DRIVE:465 1.25> Removable CD-ROM SCSI-2 device cd0: 20.000MB/s transfers (20.000MHz, offset 15) cd0: Attempt to query device size failed: NOT READY, Medium not present WARNING: / was not properly dismounted em0: Link is up 1000 Mbps Full Duplex em0: Link is up 1000 Mbps Full Duplex ---MikeReceived on Mon Aug 08 2005 - 18:42:46 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:40 UTC