I'm trying to boot a Lex barebone (VIA Eden based) off a CF card that shows up as a ad3. So far, the box has been booting off a 2.5" disk. boot and loader are RELENG_6 from Thursday. A 5-stable dmesg is attached below. When trying to boot off the CF, boot will load loader. Then the machine resets. I've tried loading /boot/kernel/kernel directly. It appears to load the kernel, but then I get a BTX panic. (I currently don't have a serial console, but I could try to transcribe the output if that would help.) How can I best debug this? Should I try earlier or later versions? I'm a bit reluctant to update loader on the hard disk: if the update makes the system unbootable, I would lose my router... Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.4-STABLE #2: Sat Jun 4 15:51:17 CEST 2005 root_at_diesel.lassitu.de:/usr/obj/usr/src/sys/DIESEL Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: VIA C3 Samuel 2 (532.64-MHz 686-class CPU) Origin = "CentaurHauls" Id = 0x673 Stepping = 3 Features=0x803035<FPU,DE,TSC,MSR,MTRR,PGE,MMX> real memory = 528416768 (503 MB) avail memory = 507424768 (483 MB) acpi0: <VIA601 AWRDACPI> on motherboard acpi0: Power Button (fixed) Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 cpu0: <ACPI CPU (3 Cx states)> on acpi0 acpi_throttle0: <ACPI CPU Throttling> on cpu0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0x6000-0x607f,0x5000-0x500f, 0x4080-0x40ff,0x4000-0x407f,0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 agp0: <VIA 8601 (Apollo ProMedia/PLE133Ta) host to PCI bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <display, VGA> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <VIA 82C686B UDMA100 controller> port 0xc000-0xc00f, 0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0 ata0: channel #0 on atapci0 ata1: channel #1 on atapci0 uhci0: <VIA 83C572 USB controller> port 0xc400-0xc41f at device 7.2 on pci0 usb0: <VIA 83C572 USB controller> on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <VIA 83C572 USB controller> port 0xc800-0xc81f at device 7.3 on pci0 usb1: <VIA 83C572 USB controller> on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pci0: <bridge> at device 7.4 (no driver attached) pcm0: <VIA VT82C686A> port 0xd400-0xd403,0xd000-0xd003,0xcc00-0xccff irq 11 at device 7.5 on pci0 pcm0: <Avance Logic ALC200 AC97 Codec> rl0: <RealTek 8139 10/100BaseTX> port 0xd800-0xd8ff mem 0xe5810000-0xe58100ff irq 12 at device 8.0 on pci0 miibus0: <MII bus> on rl0 rlphy0: <RealTek internal media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl0: Ethernet address: 00:40:f4:67:ec:84 rl1: <RealTek 8139 10/100BaseTX> port 0xdc00-0xdcff mem 0xe5811000-0xe58110ff irq 10 at device 9.0 on pci0 miibus1: <MII bus> on rl1 rlphy1: <RealTek internal media interface> on miibus1 rlphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl1: Ethernet address: 00:40:f4:67:ec:83 rl2: <RealTek 8139 10/100BaseTX> port 0xe000-0xe0ff mem 0xe5812000-0xe58120ff irq 11 at device 11.0 on pci0 miibus2: <MII bus> on rl2 rlphy2: <RealTek internal media interface> on miibus2 rlphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto rl2: Ethernet address: 00:40:f4:67:ec:82 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 npx0: <math processor> on motherboard npx0: INT 16 interface orm0: <ISA Option ROMs> at iomem 0xcc000-0xcffff,0xc0000-0xcbfff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 532640892 Hz quality 800 Timecounters tick every 10.000 msec ipfw2 initialized, divert enabled, rule-based forwarding disabled, default to accept, logging disabled ad2: 9590MB <IBM-DJSA-210/JS2AABAA> [19485/16/63] at ata1-master UDMA66 Mounting root from ufs:/dev/ad2s1a -- Stefan Bethke <stb_at_lassitu.de> Fon +49 170 346 0140Received on Sat Aug 27 2005 - 17:54:24 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:42 UTC