I updated an Aug 24 2005 (not-so current) -current up to HEAD, and have observed an extremely slow probe of fxp0 during boot of an SMP AMD64 kernel. The relevant lines from a verbose boot are fxp0: <Intel 82551 Pro/100 Ethernet> port 0xa000-0xa03f mem 0xfeafa000-0xfeafaff f,0xfeaa0000-0xfeabffff irq 18 at device 8.0 on pci3 fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfeafa000 fxp0: using memory space register mapping (6.5 minutes or longer pause here) fxp0: PCI IDs: 8086 1229 8086 1040 0010 fxp0: Dynamic Standby mode is disabled miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: bpf attached fxp0: Ethernet address: 00:e0:81:2a:59:e7 ioapic0: routing intpin 18 (PCI IRQ 18) to vector 51 fxp0: [MPSAFE] The full dmesg follows the sig. -- Steve Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 7.0-CURRENT #0: Tue Dec 20 16:05:59 PST 2005 root_at_troutmask.apl.washington.edu:/mnt1/obj/mnt1/src/sys/SPEW Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80746000. ACPI APIC Table: <A M I OEMAPIC > Calibrating clock(s) ... i8254 clock: 1193046 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 2193676782 Hz CPU: AMD Opteron(tm) Processor 248 (2193.68-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0xf58 Stepping = 8 Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2> AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow> L1 2MB data TLB: 8 entries, fully associative L1 2MB instruction TLB: 8 entries, fully associative L1 4KB data TLB: 32 entries, fully associative L1 4KB instruction TLB: 32 entries, fully associative L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L2 2MB unified TLB: 0 entries, disabled/not present L2 4KB data TLB: 512 entries, 4-way associative L2 4KB instruction TLB: 512 entries, 4-way associative L2 unified cache: 1024 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative usable memory = 12809666560 (12216 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009bfff, 634880 bytes (155 pages) 0x000000000084b000 - 0x00000000fbfeffff, 4219097088 bytes (1030053 pages) 0x0000000100000000 - 0x00000002e97bbfff, 8212168704 bytes (2004924 pages) avail memory = 12420374528 (11844 MB) APIC ID: physical 0, logical 0:0 APIC ID: physical 1, logical 0:1 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 APIC: CPU 0 has ACPI ID 1 APIC: CPU 1 has ACPI ID 2 MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000 ioapic0: Routing external 8259A's -> intpin 0 ioapic0: intpin 0 -> ExtINT (edge, high) ioapic0: intpin 1 -> ISA IRQ 1 (edge, high) ioapic0: intpin 2 -> ISA IRQ 2 (edge, high) ioapic0: intpin 3 -> ISA IRQ 3 (edge, high) ioapic0: intpin 4 -> ISA IRQ 4 (edge, high) ioapic0: intpin 5 -> ISA IRQ 5 (edge, high) ioapic0: intpin 6 -> ISA IRQ 6 (edge, high) ioapic0: intpin 7 -> ISA IRQ 7 (edge, high) ioapic0: intpin 8 -> ISA IRQ 8 (edge, high) ioapic0: intpin 9 -> ISA IRQ 9 (edge, high) ioapic0: intpin 10 -> ISA IRQ 10 (edge, high) ioapic0: intpin 11 -> ISA IRQ 11 (edge, high) ioapic0: intpin 12 -> ISA IRQ 12 (edge, high) ioapic0: intpin 13 -> ISA IRQ 13 (edge, high) ioapic0: intpin 14 -> ISA IRQ 14 (edge, high) ioapic0: intpin 15 -> ISA IRQ 15 (edge, high) ioapic0: intpin 16 -> PCI IRQ 16 (level, low) ioapic0: intpin 17 -> PCI IRQ 17 (level, low) ioapic0: intpin 18 -> PCI IRQ 18 (level, low) ioapic0: intpin 19 -> PCI IRQ 19 (level, low) ioapic0: intpin 20 -> PCI IRQ 20 (level, low) ioapic0: intpin 21 -> PCI IRQ 21 (level, low) ioapic0: intpin 22 -> PCI IRQ 22 (level, low) ioapic0: intpin 23 -> PCI IRQ 23 (level, low) MADT: Found IO APIC ID 3, Interrupt 24 at 0xfebff000 ioapic1: intpin 0 -> PCI IRQ 24 (level, low) ioapic1: intpin 1 -> PCI IRQ 25 (level, low) ioapic1: intpin 2 -> PCI IRQ 26 (level, low) ioapic1: intpin 3 -> PCI IRQ 27 (level, low) MADT: Found IO APIC ID 4, Interrupt 28 at 0xfebfe000 ioapic2: intpin 0 -> PCI IRQ 28 (level, low) ioapic2: intpin 1 -> PCI IRQ 29 (level, low) ioapic2: intpin 2 -> PCI IRQ 30 (level, low) ioapic2: intpin 3 -> PCI IRQ 31 (level, low) MADT: Interrupt override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 ioapic0: intpin 2 trigger: edge ioapic0: intpin 2 polarity: high MADT: Interrupt override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 ioapic0: intpin 2 trigger: edge ioapic0: intpin 2 polarity: high MADT: Forcing active-low polarity and level trigger for SCI ioapic0: intpin 9 polarity: low ioapic0: intpin 9 trigger: level ioapic0 <Version 1.1> irqs 0-23 on motherboard ioapic1 <Version 1.1> irqs 24-27 on motherboard ioapic2 <Version 1.1> irqs 28-31 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00000000 err: 0x0001000f pcm: 0x00010000 mem: <memory> null: <null device, zero device> nfslock: pseudo-device random: <entropy source, Software, Yarrow> io: <I/O> acpi0: <A M I OEMXSDT> on motherboard ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48 acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x80023000 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 1 2 3 4 5 6 [class=060400] [hdr=01] is there (id=74601022) AcpiOsDerivePciId: bus 0 dev 7 func 0 AcpiOsDerivePciId: bus 0 dev 7 func 1 AcpiOsDerivePciId: bus 0 dev 7 func 3 acpi0: Power Button (fixed) AcpiOsDerivePciId: bus 0 dev 10 func 0 AcpiOsDerivePciId: bus 0 dev 11 func 0 pci_link0: Links after initial probe: Index IRQ Rtd Ref IRQs 0 10 N 0 3 4 5 6 7 9 10 11 12 14 15 pci_link0: Links after initial validation: Index IRQ Rtd Ref IRQs 0 10 N 0 3 4 5 6 7 9 10 11 12 14 15 pci_link0: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15 pci_link1: Links after initial probe: Index IRQ Rtd Ref IRQs 0 15 N 0 3 4 5 6 7 9 10 11 12 14 15 pci_link1: Links after initial validation: Index IRQ Rtd Ref IRQs 0 15 N 0 3 4 5 6 7 9 10 11 12 14 15 pci_link1: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15 pci_link2: Links after initial probe: Index IRQ Rtd Ref IRQs 0 11 N 0 3 4 5 6 7 9 10 11 12 14 15 pci_link2: Links after initial validation: Index IRQ Rtd Ref IRQs 0 11 N 0 3 4 5 6 7 9 10 11 12 14 15 pci_link2: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15 pci_link3: Links after initial probe: Index IRQ Rtd Ref IRQs 0 9 N 0 3 4 5 6 7 9 10 11 12 14 15 pci_link3: Links after initial validation: Index IRQ Rtd Ref IRQs 0 9 N 0 3 4 5 6 7 9 10 11 12 14 15 pci_link3: Links after disable: Index IRQ Rtd Ref IRQs 0 255 N 0 3 4 5 6 7 9 10 11 12 14 15 ACPI timer: 1/2 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x5008-0x500b on acpi0 cpu0: <ACPI CPU> on acpi0 acpi_throttle0: <ACPI CPU Throttling> on cpu0 acpi_throttle0: P_CNT from P_BLK 0x5010 cpu1: <ACPI CPU> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x1022, dev=0x7460, revid=0x07 bus=0, slot=6, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0117, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x0a (2500 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7468, revid=0x05 bus=0, slot=7, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7469, revid=0x03 bus=0, slot=7, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[20]: type 4, range 32, base 0000ffa0, size 4, port disabled found-> vendor=0x1022, dev=0x746a, revid=0x02 bus=0, slot=7, func=2 class=0c-05-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=9 map[10]: type 4, range 32, base 0000cc00, size 5, enabled pcib0: matched entry for 0.7.INTD pcib0: slot 7 INTD hardwired to IRQ 19 found-> vendor=0x1022, dev=0x746b, revid=0x05 bus=0, slot=7, func=3 class=06-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7450, revid=0x12 bus=0, slot=10, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0117, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7451, revid=0x01 bus=0, slot=10, func=1 class=08-00-10, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 1, range 64, base febff000, size 12, enabled found-> vendor=0x1022, dev=0x7450, revid=0x12 bus=0, slot=11, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0116, statreg=0x0230, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7451, revid=0x01 bus=0, slot=11, func=1 class=08-00-10, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 1, range 64, base febfe000, size 12, enabled found-> vendor=0x1022, dev=0x1100, revid=0x00 bus=0, slot=24, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1101, revid=0x00 bus=0, slot=24, func=1 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1102, revid=0x00 bus=0, slot=24, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1103, revid=0x00 bus=0, slot=24, func=3 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1100, revid=0x00 bus=0, slot=25, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1101, revid=0x00 bus=0, slot=25, func=1 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1102, revid=0x00 bus=0, slot=25, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1103, revid=0x00 bus=0, slot=25, func=3 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0 pcib1: secondary bus 3 pcib1: subordinate bus 3 pcib1: I/O decode 0x9000-0xbfff pcib1: memory decode 0xfc900000-0xfeafffff pcib1: prefetched decode 0xfff00000-0xfffff pci3: <ACPI PCI bus> on pcib1 pci3: physical bus=3 found-> vendor=0x1022, dev=0x7464, revid=0x0b bus=3, slot=0, func=0 class=0c-03-10, hdrtype=0x00, mfdev=1 cmdreg=0x0117, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns) intpin=d, irq=9 map[10]: type 1, range 32, base feafc000, size 12, enabled pcib1: (null) requested memory range 0xfeafc000-0xfeafcfff: good pcib1: matched entry for 3.0.INTD pcib1: slot 0 INTD hardwired to IRQ 19 found-> vendor=0x1022, dev=0x7464, revid=0x0b bus=3, slot=0, func=1 class=0c-03-10, hdrtype=0x00, mfdev=0 cmdreg=0x0117, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns) intpin=d, irq=9 map[10]: type 1, range 32, base feafd000, size 12, enabled pcib1: (null) requested memory range 0xfeafd000-0xfeafdfff: good pcib1: matched entry for 3.0.INTD pcib1: slot 0 INTD hardwired to IRQ 19 found-> vendor=0x9004, dev=0x8178, revid=0x00 bus=3, slot=4, func=0 class=01-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0117, statreg=0x0280, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns) intpin=a, irq=10 map[10]: type 4, range 32, base 0000b400, size 8, enabled pcib1: (null) requested I/O range 0xb400-0xb4ff: in range map[14]: type 1, range 32, base feafe000, size 12, enabled pcib1: (null) requested memory range 0xfeafe000-0xfeafefff: good pcib1: matched entry for 3.4.INTA pcib1: slot 4 INTA hardwired to IRQ 16 found-> vendor=0x1095, dev=0x3114, revid=0x02 bus=3, slot=5, func=0 class=01-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0107, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=9 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 4, range 32, base 0000bc00, size 3, enabled pcib1: (null) requested I/O range 0xbc00-0xbc07: in range map[14]: type 4, range 32, base 0000b000, size 2, enabled pcib1: (null) requested I/O range 0xb000-0xb003: in range map[18]: type 4, range 32, base 0000ac00, size 3, enabled pcib1: (null) requested I/O range 0xac00-0xac07: in range map[1c]: type 4, range 32, base 0000a800, size 2, enabled pcib1: (null) requested I/O range 0xa800-0xa803: in range map[20]: type 4, range 32, base 0000a400, size 4, enabled pcib1: (null) requested I/O range 0xa400-0xa40f: in range map[24]: type 1, range 32, base feafbc00, size 10, enabled pcib1: (null) requested memory range 0xfeafbc00-0xfeafbfff: good pcib1: matched entry for 3.5.INTA pcib1: slot 5 INTA hardwired to IRQ 19 found-> vendor=0x1002, dev=0x4752, revid=0x27 bus=3, slot=6, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0087, statreg=0x0290, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base fd000000, size 24, enabled pcib1: (null) requested memory range 0xfd000000-0xfdffffff: good map[14]: type 4, range 32, base 0000b800, size 8, enabled pcib1: (null) requested I/O range 0xb800-0xb8ff: in range map[18]: type 1, range 32, base feaff000, size 12, enabled pcib1: (null) requested memory range 0xfeaff000-0xfeafffff: good pcib1: matched entry for 3.6.INTA pcib1: slot 6 INTA hardwired to IRQ 18 found-> vendor=0x8086, dev=0x1229, revid=0x10 bus=3, slot=8, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0117, statreg=0x0290, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base feafa000, size 12, enabled pcib1: (null) requested memory range 0xfeafa000-0xfeafafff: good map[14]: type 4, range 32, base 0000a000, size 6, enabled pcib1: (null) requested I/O range 0xa000-0xa03f: in range map[18]: type 1, range 32, base feaa0000, size 17, enabled pcib1: (null) requested memory range 0xfeaa0000-0xfeabffff: good pcib1: matched entry for 3.8.INTA pcib1: slot 8 INTA hardwired to IRQ 18 ohci0: <OHCI (generic) USB controller> mem 0xfeafc000-0xfeafcfff irq 19 at device 0.0 on pci3 ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfeafc000 ioapic0: routing intpin 19 (PCI IRQ 19) to vector 49 ohci0: [GIANT-LOCKED] usb0: OHCI version 1.0, legacy support usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 3 ports with 3 removable, self powered ohci1: <OHCI (generic) USB controller> mem 0xfeafd000-0xfeafdfff irq 19 at device 0.1 on pci3 ohci1: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfeafd000 ohci1: [GIANT-LOCKED] usb1: OHCI version 1.0, legacy support usb1: <OHCI (generic) USB controller> on ohci1 usb1: USB revision 1.0 uhub1: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 3 ports with 3 removable, self powered ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0xb400-0xb4ff mem 0xfeafe000-0xfeafefff irq 16 at device 4.0 on pci3 ahc0: Defaulting to MEMIO off ahc0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xb400 ahc0: Enabling 39Bit Addressing ahc0: Reading SEEPROM...done. ahc0: internal 50 cable is present ahc0: external cable not present ahc0: BIOS eeprom is present ahc0: Low byte termination Enabled ahc0: Downloading Sequencer Program... 450 instructions downloaded ahc0: Features 0x10001, Bugs 0x25, Flags 0x21481540 ioapic0: routing intpin 16 (PCI IRQ 16) to vector 50 ahc0: [GIANT-LOCKED] aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs pci3: <mass storage> at device 5.0 (no driver attached) vgapci0: <VGA-compatible display> port 0xb800-0xb8ff mem 0xfd000000-0xfdffffff,0xfeaff000-0xfeafffff irq 18 at device 6.0 on pci3 fxp0: <Intel 82551 Pro/100 Ethernet> port 0xa000-0xa03f mem 0xfeafa000-0xfeafafff,0xfeaa0000-0xfeabffff irq 18 at device 8.0 on pci3 fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfeafa000 fxp0: using memory space register mapping fxp0: PCI IDs: 8086 1229 8086 1040 0010 fxp0: Dynamic Standby mode is disabled miibus0: <MII bus> on fxp0 inphy0: <i82555 10/100 media interface> on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: bpf attached fxp0: Ethernet address: 00:e0:81:2a:59:e7 ioapic0: routing intpin 18 (PCI IRQ 18) to vector 51 fxp0: [MPSAFE] isab0: <PCI-ISA bridge> at device 7.0 on pci0 isa0: <ISA bus> on isab0 pci0: <mass storage, ATA> at device 7.1 (no driver attached) pci0: <serial bus, SMBus> at device 7.2 (no driver attached) amdpm0: <AMD 756/766/768/8111 Power Management Controller> port 0x50e0-0x50ff at device 7.3 on pci0 smbus0: <System Management Bus> on amdpm0 smb0: <SMBus generic I/O> on smbus0 pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0x8000-0x8fff pcib2: memory decode 0xfc600000-0xfc8fffff pcib2: prefetched decode 0xff500000-0xff5fffff pci2: <ACPI PCI bus> on pcib2 pci2: physical bus=2 found-> vendor=0x9005, dev=0x801d, revid=0x10 bus=2, slot=6, func=0 class=01-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0117, statreg=0x0430, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 MSI supports 2 messages, 64 bit map[10]: type 4, range 32, base 00008000, size 8, enabled pcib2: (null) requested I/O range 0x8000-0x80ff: in range map[14]: type 1, range 64, base fc8fc000, size 13, enabled pcib2: (null) requested memory range 0xfc8fc000-0xfc8fdfff: good map[1c]: type 4, range 32, base 00008c00, size 8, enabled pcib2: (null) requested I/O range 0x8c00-0x8cff: in range pcib2: matched entry for 2.6.INTA pcib2: slot 6 INTA hardwired to IRQ 24 found-> vendor=0x9005, dev=0x801d, revid=0x10 bus=2, slot=6, func=1 class=01-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0117, statreg=0x0430, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x28 (10000 ns), maxlat=0x19 (6250 ns) intpin=b, irq=15 powerspec 2 supports D0 D3 current D0 MSI supports 2 messages, 64 bit map[10]: type 4, range 32, base 00008800, size 8, enabled pcib2: (null) requested I/O range 0x8800-0x88ff: in range map[14]: type 1, range 64, base fc8fe000, size 13, enabled pcib2: (null) requested memory range 0xfc8fe000-0xfc8fffff: good map[1c]: type 4, range 32, base 00008400, size 8, enabled pcib2: (null) requested I/O range 0x8400-0x84ff: in range pcib2: matched entry for 2.6.INTB pcib2: slot 6 INTB hardwired to IRQ 25 ahd0: <Adaptec AIC7902 Ultra320 SCSI adapter> port 0x8000-0x80ff,0x8c00-0x8cff mem 0xfc8fc000-0xfc8fdfff irq 24 at device 6.0 on pci2 ahd0: Defaulting to MEMIO on ahd0: Reserved 0x2000 bytes for rid 0x14 type 3 at 0xfc8fc000 ahd0: Enabling 39Bit Addressing ahd0: Reading VPD from SEEPROM...ahd0: VPD parsing successful ahd0: Reading SEEPROM...done. ahd0: STPWLEVEL is on ahd0: Manual Primary Termination ahd0: Manual Secondary Termination ahd0: Primary High byte termination Enabled ahd0: Primary Low byte termination Enabled ahd0: Secondary High byte termination Disabled ahd0: Secondary Low byte termination Disabled ahd0: Downloading Sequencer Program... 697 instructions downloaded ahd0: Features 0x3c101, Bugs 0x740002, Flags 0x143f1 ioapic1: routing intpin 0 (PCI IRQ 24) to vector 52 ahd0: [GIANT-LOCKED] aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs ahd1: <Adaptec AIC7902 Ultra320 SCSI adapter> port 0x8800-0x88ff,0x8400-0x84ff mem 0xfc8fe000-0xfc8fffff irq 25 at device 6.1 on pci2 ahd1: Defaulting to MEMIO on ahd1: Reserved 0x2000 bytes for rid 0x14 type 3 at 0xfc8fe000 ahd1: Enabling 39Bit Addressing ahd1: Reading VPD from SEEPROM...ahd1: VPD parsing successful ahd1: Reading SEEPROM...done. ahd1: STPWLEVEL is on ahd1: Manual Primary Termination ahd1: Manual Secondary Termination ahd1: Primary High byte termination Enabled ahd1: Primary Low byte termination Enabled ahd1: Secondary High byte termination Disabled ahd1: Secondary Low byte termination Disabled ahd1: Downloading Sequencer Program... 697 instructions downloaded ahd1: Features 0x3c101, Bugs 0x740002, Flags 0x143f0 ioapic1: routing intpin 1 (PCI IRQ 25) to vector 53 ahd1: [GIANT-LOCKED] aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs pci0: <base peripheral, interrupt controller> at device 10.1 (no driver attached) pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0 pcib3: secondary bus 1 pcib3: subordinate bus 1 pcib3: I/O decode 0x0-0x0 pcib3: memory decode 0xfff00000-0xfffff pcib3: prefetched decode 0xfff00000-0xfffff pci1: <ACPI PCI bus> on pcib3 pci1: physical bus=1 pci0: <base peripheral, interrupt controller> at device 11.1 (no driver attached) acpi_button0: <Power Button> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000 ioapic0: routing intpin 1 (ISA IRQ 1) to vector 54 atkbd0: [GIANT-LOCKED] psm0: unable to allocate IRQ psmcpnp0: <PS/2 mouse port> irq 12 on acpi0 psm0: current command byte:0065 psm0: <PS/2 Mouse> irq 12 on atkbdc0 ioapic0: routing intpin 12 (ISA IRQ 12) to vector 55 psm0: [GIANT-LOCKED] psm0: model Generic PS/2 mouse, device ID 0-00, 3 buttons psm0: config:00000000, flags:00000008, packet size:3 psm0: syncmask:c0, syncbits:00 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0 0 0 0 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A ioapic0: routing intpin 4 (ISA IRQ 4) to vector 56 sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0 0 0 0 sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0 sio1: type 16550A ioapic0: routing intpin 3 (ISA IRQ 3) to vector 57 fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: ic_type 90 part_id 80 ioapic0: routing intpin 6 (ISA IRQ 6) to vector 58 fdc0: [MPSAFE] fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 ppc0: using extended I/O port range ppc0: SPP ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 plip0: bpf attached lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 ioapic0: routing intpin 7 (ISA IRQ 7) to vector 59 acpi_hpet0: <HPET - High Precision Event Timers> iomem 0xfec01000-0xfec013ff irq 0,8 on acpi0 acpi_hpet0: Vendor: 0x1022 acpi_hpet0: Leg_Route_Cap: 1 acpi_hpet0: Count_Size_Cap: 0 acpi_hpet0: Num_Tim_Cap: 8 acpi_hpet0: Rev_id: 0x3 acpi_hpet0: Period: 69841279 fs (14318180 Hz) acpi_hpet0: HPET attach Timecounter "HPET" frequency 14318180 Hz quality -200 atkbdc: atkbdc0 already exists; skipping it fdc: fdc0 already exists; skipping it ppc: ppc0 already exists; skipping it sio: sio0 already exists; skipping it sio: sio1 already exists; skipping it pnp_identify: Trying Read_Port at 203 pnp_identify: Trying Read_Port at 243 pnp_identify: Trying Read_Port at 283 pnp_identify: Trying Read_Port at 2c3 pnp_identify: Trying Read_Port at 303 pnp_identify: Trying Read_Port at 343 pnp_identify: Trying Read_Port at 383 pnp_identify: Trying Read_Port at 3c3 PNP Identify complete sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it ahc_isa_probe 0: ioport 0xc00 alloc failed ahc_isa_probe 8: ioport 0x8c00 alloc failed ahc_isa_probe 10: ioport 0xac00 alloc failed ahc_isa_probe 11: ioport 0xbc00 alloc failed ahc_isa_probe 12: ioport 0xcc00 alloc failed isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcc7ff,0xd5800-0xd9fff pnpid ORM0000 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <8 virtual consoles, flags=0x300> sc0: fb0, kbd0, terminal emulator: sc (syscons terminal) sio2: not probed (disabled) sio3: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 isa_probe_children: probing PnP devices Device configuration finished. Reducing kern.maxvnodes 243854 -> 100000 procfs registered linprocfs registered lapic: Divisor 2, Frequency 99712590 hz Timecounter "TSC" frequency 2193676782 Hz quality -100 Timecounters tick every 1.000 msec Linux ELF exec handler installed lo0: bpf attached Waiting 3 seconds for SCSI devices to settle (noperiph:ahd0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. (noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. (noperiph:ahd1:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted. ahd0: Selection Timeout on A:3. 0 SCBs aborted ahd1: Selection Timeout on A:0. 0 SCBs aborted ahc0: Selection Timeout on A:3. 0 SCBs aborted ahd0: Selection Timeout on A:4. 0 SCBs aborted ahd1: Selection Timeout on A:1. 0 SCBs aborted ahc0: Selection Timeout on A:6. 0 SCBs aborted ahd0: Selection Timeout on A:5. 0 SCBs aborted ahd1: Selection Timeout on A:3. 0 SCBs aborted ahc0: Selection Timeout on A:1. 0 SCBs aborted ahd0: Selection Timeout on A:11. 0 SCBs aborted ahd1: Selection Timeout on A:4. 0 SCBs aborted ahc0: Selection Timeout on A:2. 0 SCBs aborted (probe15:ahc0:0:0:0): Retrying Command (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f ahc0: target 4 synchronous at 10.0MHz, offset = 0xf (ahc0:A:5:0): Sending SDTR period 19, offset f (ahc0:A:5:0): Received SDTR period 32, offset f Filtered to period 32, offset f ahc0: target 5 synchronous at 5.0MHz, offset = 0xf (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (ahc0:A:5:0): Sending SDTR period 32, offset f (ahc0:A:5:0): Received SDTR period 32, offset f Filtered to period 32, offset f (ahc0:A:0:0): Sending SDTR period 19, offset f (ahc0:A:0:0): Received SDTR period 19, offset f Filtered to period 19, offset f ahc0: target 0 synchronous at 10.0MHz, offset = 0xf ahd0: Selection Timeout on A:12. 0 SCBs aborted ahd1: Selection Timeout on A:5. 0 SCBs aborted ahd0: Selection Timeout on A:13. 0 SCBs aborted ahd1: Selection Timeout on A:6. 0 SCBs aborted ahd0: Selection Timeout on A:1. 0 SCBs aborted ahd1: Selection Timeout on A:8. 0 SCBs aborted ahd0: Selection Timeout on A:2. 0 SCBs aborted ahd1: Selection Timeout on A:9. 0 SCBs aborted ahd0: Selection Timeout on A:6. 0 SCBs aborted ahd1: Selection Timeout on A:10. 0 SCBs aborted ahd0: Selection Timeout on A:8. 0 SCBs aborted ahd1: Selection Timeout on A:11. 0 SCBs aborted ahd0: Selection Timeout on A:9. 0 SCBs aborted ahd1: Selection Timeout on A:12. 0 SCBs aborted ahd0: Selection Timeout on A:10. 0 SCBs aborted ahd1: Selection Timeout on A:13. 0 SCBs aborted ahd0: Selection Timeout on A:14. 0 SCBs aborted ahd1: Selection Timeout on A:14. 0 SCBs aborted ahd0: Selection Timeout on A:15. 0 SCBs aborted (probe0:ahd0:0:0:0): Retrying Command (ahd0:A:0:0): Sending PPR bus_width 1, period 8, offset fe, ppr_options ff ahd1: Selection Timeout on A:15. 0 SCBs aborted (ahd0:A:0:0): Received PPR width 1, period 8, offset 3f,options ff Filtered to width 1, period 8, offset 3f, options ff ahd0: target 0 using 16bit transfers ahd0: target 0 synchronous with period = 0x8, offset = 0x3f(RDSTRM|DT|IU|RTI|QAS) ahd1: Selection Timeout on A:2. 0 SCBs aborted pass0 at ahd0 bus 0 target 0 lun 0 pass0: <SEAGATE ST373307LW 0007> Fixed Direct Access SCSI-3 device pass0: Serial Number 3HZ805ZE00007436F79B pass0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing Enabled pass1 at ahc0 bus 0 target 0 lun 0 pass1: <SEAGATE ST39216N 0010> Fixed Direct Access SCSI-3 device pass1: Serial Number 3BN12XT600007124NH7V pass1: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled pass2 at ahc0 bus 0 target 4 lun 0 pass2: <PLEXTOR CD-R PX-W4012S 1.01> Removable CD-ROM SCSI-2 device pass2: Serial Number 3 pass2: 10.000MB/s transfers (10.000MHz, offset 15) pass3 at ahc0 bus 0 target 5 lun 0 pass3: <DEC DLT2000 8B37> Removable Sequential Access SCSI-2 device pass3: Serial Number CX837T0309 pass3: 5.000MB/s transfers (5.000MHz, offset 15) sa0 at ahc0 bus 0 target 5 lun 0 sa0: <DEC DLT2000 8B37> Removable Sequential Access SCSI-2 device sa0: Serial Number CX837T0309 sa0: 5.000MB/s transfers (5.000MHz, offset 15) da1 at ahc0 bus 0 target 0 lun 0 da1: <SEAGATE ST39216N 0010> Fixed Direct Access SCSI-3 device da1: Serial Number 3BN12XT600007124NH7V da1: 10.000MB/s transfers (10.000MHz, offset 15), Tagged Queueing Enabled da1: 8761MB (17942584 512 byte sectors: 255H 63S/T 1116C) da0 at ahd0 bus 0 target 0 lun 0 da0: <SEAGATE ST373307LW 0007> Fixed Direct Access SCSI-3 device da0: Serial Number 3HZ805ZE00007436F79B da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged Queueing Enabled da0: 70007MB (143374744 512 byte sectors: 255H 63S/T 8924C) GEOM: new disk da0(ahc0:A:4:0): Sending SDTR period 19, offset f GEOM: n(ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f ew disk da1(cd0:ahc0:0:4:0): Retrying Command GEOM: new disk cd0 SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x01000000 VER: 0x00040010 LDR: 0x02000000 DFR: 0x0fffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000200ef therm: 0x00000000 err: 0x00010000 pcm: 0x00010000 ioapic0: routing intpin 1 (ISA IRQ 1) to cluster 0 ioapic0: routing intpin 3 (ISA IRQ 3) to cluster 0 ioapic0: routing intpin 4 (ISA IRQ 4) to cluster 0 ioapic0: routing intpin 6 (ISA IRQ 6) to cluster 0 ioapic0: routing intpin 7 (ISA IRQ 7) to cluster 0 ioapic0: routing intpin 9 (ISA IRQ 9) to cluster 0 ioapic0: routing intpin 12 (ISA IRQ 12) to cluster 0 ioapic0: routing intpin 16 (PCI IRQ 16) to cluster 0 ioapic0: routing intpin 18 (PCI IRQ 18) to cluster 0 ioapic0: routing intpin 19 (PCI IRQ 19) to cluster 0 ioapic1: routing intpin 0 (PCI IRQ 24) to cluster 0 ioapic1: routing intpin 1 (PCI IRQ 25) to cluster 0 (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f cd0 at ahc0 bus 0 target 4 lun 0 cd0: <PLEXTOR CD-R PX-W4012S 1.01> Removable CD-ROM SCSI-2 device cd0: Serial Number 3 cd0: 10.000MB/s transfers (10.000MHz, offset 15) cd0: cd present [190950 x 2048 byte records] (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 (cd0:ahc0:0:4:0): CAM Status: SCSI Status Error (cd0:ahc0:0:4:0): SCSI Status: Check Condition (cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0 (cd0:ahc0:0:4:0): Illegal mode for this track (cd0:ahc0:0:4:0): (cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 (cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0 (cd0:ahc0:0:4:0): Illegal mode for this track Unretryable error (cd0:ahc0:0:4:0): error 6 (cd0:ahc0:0:4:0): Unretryable Error (cd0:ahc0:0:4:0): cddone: got error 0x6 back (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 1 0 0 1 0 (cd0:ahc0:0:4:0): CAM Status: SCSI Status Error (cd0:ahc0:0:4:0): SCSI Status: Check Condition (cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0 (cd0:ahc0:0:4:0): Illegal mode for this track (cd0:ahc0:0:4:0): (cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 1 0 0 1 0 (cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0 (cd0:ahc0:0:4:0): Illegal mode for this track Unretryable error (cd0:ahc0:0:4:0): error 6 (cd0:ahc0:0:4:0): Unretryable Error (cd0:ahc0:0:4:0): cddone: got error 0x6 back (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 (cd0:ahc0:0:4:0): CAM Status: SCSI Status Error (cd0:ahc0:0:4:0): SCSI Status: Check Condition (cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0 (cd0:ahc0:0:4:0): Illegal mode for this track (cd0:ahc0:0:4:0): (cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 (cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0 (cd0:ahc0:0:4:0): Illegal mode for this track Unretryable error (cd0:ahc0:0:4:0): error 6 (cd0:ahc0:0:4:0): Unretryable Error (cd0:ahc0:0:4:0): cddone: got error 0x6 back (ahc0:A:4:0): Sending SDTR period 19, offset f (ahc0:A:4:0): Received SDTR period 19, offset f Filtered to period 19, offset f (cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 (cd0:ahc0:0:4:0): CAM Status: SCSI Status Error (cd0:ahc0:0:4:0): SCSI Status: Check Condition (cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0 (cd0:ahc0:0:4:0): Illegal mode for this track (cd0:ahc0:0:4:0): (cd0:ahc0:0:4:0): READ(10). CDB: 28 0 0 0 0 0 0 0 1 0 (cd0:ahc0:0:4:0): ILLEGAL REQUEST asc:64,0 (cd0:ahc0:0:4:0): Illegal mode for this track Unretryable error (cd0:ahc0:0:4:0): error 6 (cd0:ahc0:0:4:0): Unretryable Error (cd0:ahc0:0:4:0): cddone: got error 0x6 back Trying to mount root from ufs:/dev/da0s1a start_init: trying /sbin/init (da0:ahd0:0:0:0): Request Requeued (da0:ahd0:0:0:0): Retrying Command (da0:ahd0:0:0:0): Queue Full (da0:ahd0:0:0:0): tagged openings now 63 (da0:ahd0:0:0:0): Retrying CommandReceived on Wed Dec 21 2005 - 00:57:15 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:49 UTC