Re: Adaptec 39320A "Card was not paused"

Cameron Murdoch wrote:
> I am having a problem with an adaptec 39320A SCSI card accessing an 
> external raid box, (JetStor III 416S).
> 
> Host computer is a Dell PowerEdge2650 with a single processor.
> 
> 6-CURRENT from Saturday has the following relevant dmesg:
> 
> **snip**
> Jan 16 21:13:35  kernel: ahd0: <Adaptec 39320A Ultra320 SCSI adapter> 
> port 0xd800-0xd8ff,0xdc00-0xdcff mem 0xfcf02000-0xfcf03fff irq 20 at 
> device 8.0 on pci1
> Jan 16 21:13:35  kernel: ahd0: [GIANT-LOCKED]
> Jan 16 21:13:35  kernel: aic7902: Ultra320 Wide Channel A, SCSI Id=7, 
> PCI-X 101-133Mhz, 512 SCBs
> Jan 16 21:13:35  kernel: ahd1: <Adaptec 39320A Ultra320 SCSI adapter> 
> port 0xd000-0xd0ff,0xd400-0xd4ff mem 0xfcf00000-0xfcf01fff irq 21 at 
> device 8.1 on pci1
> Jan 16 21:13:35  kernel: ahd1: [GIANT-LOCKED]
> Jan 16 21:13:35  kernel: aic7902: Ultra320 Wide Channel B, SCSI Id=7, 
> PCI-X 101-133Mhz, 512 SCBs
> **snip**
> Jan 16 21:13:35  kernel: da0 at ahd0 bus 0 target 0 lun 0
> Jan 16 21:13:35  kernel: da0: <JetStor Volume Set # 00 R001> Fixed 
> Direct Access SCSI-3 device
> Jan 16 21:13:35  kernel: da0: 320.000MB/s transfers (160.000MHz, offset 
> 127, 16bit), Tagged Queueing Enabled
> Jan 16 21:13:35  kernel: da0: 1192092MB (2441405440 512 byte sectors: 
> 255H 63S/T 151970C)
> 
> Attempts to newfs a bsdlabeled slice results in the following errors:
> 
> Jan 16 21:20:21  kernel: ahd0: Recovery Initiated - Card was not paused
> Jan 16 21:20:21  kernel: >>>>>>>>>>>>>>>>>> Dump Card State Begins 
> <<<<<<<<<<<<<<<<<
> Jan 16 21:20:21  kernel: ahd0: Dumping Card State at program address 
> 0x81 Mode 0x22
> Jan 16 21:20:21  kernel: INTSTAT[0x0] SELOID[0x0] SELID[0x0] 
> HS_MAILBOX[0x0]
> Jan 16 21:20:21  kernel: INTCTL[0x80]:(SWTMINTMASK) SEQINTSTAT[0x0] 
> SAVED_MODE[0x11]
> Jan 16 21:20:21  kernel: DFFSTAT[0x33]:(CURRFIFO_NONE|FIFO0FREE|FIFO1FREE)
> Jan 16 21:20:21  kernel: SCSISIGI[0x25]:(P_DATAOUT_DT|ACKI|BSYI) 
> SCSIPHASE[0x0]
> Jan 16 21:20:21  kernel: SCSIBUS[0x0] LASTPHASE[0x1]:(P_DATAOUT|P_BUSFREE)
> Jan 16 21:20:21  kernel: SCSISEQ0[0x40]:(ENSELO) 
> SCSISEQ1[0x12]:(ENAUTOATNP|ENRSELI)
> Jan 16 21:20:21  kernel: SEQCTL0[0x0] SEQINTCTL[0x0] SEQ_FLAGS[0x0] 
> SEQ_FLAGS2[0x0]
> Jan 16 21:20:21  kernel: QFREEZE_COUNT[0x0] KERNEL_QFREEZE_COUNT[0x0] 
> MK_MESSAGE_SCB[0xff00]
> Jan 16 21:20:21  kernel: MK_MESSAGE_SCSIID[0xff] SSTAT0[0x10]:(SELINGO) 
> SSTAT1[0x8]:(BUSFREE)
> Jan 16 21:20:21  kernel: SSTAT2[0x0] SSTAT3[0x0] 
> PERRDIAG[0xc0]:(HIPERR|HIZERO)
> Jan 16 21:20:21  kernel: SIMODE1[0xa4]:(ENSCSIPERR|ENSCSIRST|ENSELTIMO) 
> LQISTAT0[0x0]
> Jan 16 21:20:21  kernel: LQISTAT1[0x0] LQISTAT2[0x80]:(PACKETIZED) 
> LQOSTAT0[0x0]
> Jan 16 21:20:21  kernel: LQOSTAT1[0x0] LQOSTAT2[0x40]
> **snip (lots of debugging output)**

You snipped off the output that was important.  Send a complete log, please.


Scott