At 03:20 PM 06/07/2005, John Baldwin wrote: >On Wednesday 06 July 2005 01:54 pm, Mike Tancsa wrote: > > At 12:23 PM 06/07/2005, Mike Tancsa wrote: > > >At 11:53 AM 06/07/2005, Mike Tancsa wrote: > > >>At 11:43 AM 06/07/2005, Scott Long wrote: > > >>>According to the original dmesg, the hang happens well after bus > > >>>enumeration is complete and interrupts have been enabled. It's > > >>>happening on a taste I/O from GEOM. > > >> > > >>Here is a boot -v that is a little more upto date. I am just netbooting > > >>with various kernel configs to try and sort out whats going on. > > > > And here is the box booting up with RELENG_5 off the disk. I did at one > > point install HEAD on the disk, but it was the same behaviour as I see with > > a netboot. > >Hmm, this dmesg has ACPI disabled whereas the 6.0 one had ACPI enabled. Are >all the IRQs the same in the 5.x and 6.0 cases? Actually, on RELENG_5, ACPI does not work in that my NIC errors out at boot up time /boot/kernel/acpi.ko text=0x414dc data=0x1dc4+0x112c syms=[0x4+0x7670+0x4+0x9d05] Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.4-STABLE #0: Thu Jun 30 19:15:07 EDT 2005 mdtancsa_at_hippo.sentex.ca:/usr/obj/usr/src/sys/hippo Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Pentium III/Pentium III Xeon/Celeron (500.02-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x672 Stepping = 2 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 2147475456 (2047 MB) avail memory = 2096021504 (1998 MB) ACPI APIC Table: <DELL PE6350 > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs cpu0 (BSP): APIC ID: 3 cpu1 (AP): APIC ID: 0 cpu2 (AP): APIC ID: 1 cpu3 (AP): APIC ID: 2 ioapic0: Changing APIC ID to 4 ioapic0 <Version 1.1> irqs 0-23 on motherboard npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <DELL PE6350> on motherboard acpi0: Power Button (fixed) Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 cpu2: <ACPI CPU> on acpi0 cpu3: <ACPI CPU> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 isab0: <PCI-ISA bridge> at device 2.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel PIIX4 UDMA33 controller> port 0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 2.1 on pci0 ata0: channel #0 on atapci0 ata1: channel #1 on atapci0 pci0: <serial bus, USB> at device 2.2 (no driver attached) pci0: <bridge> at device 2.3 (no driver attached) pci0: <display, VGA> at device 4.0 (no driver attached) pcib1: <ACPI Host-PCI bridge> on acpi0 pci1: <ACPI PCI bus> on pcib1 pcib2: <ACPI Host-PCI bridge> on acpi0 pci2: <ACPI PCI bus> on pcib2 em0: <Intel(R) PRO/1000 Network Connection, Version - 1.7.35> port 0xecc0-0xecff mem 0xfeb00000-0xfeb1ffff,0xfeb20000-0xfeb3ffff ir2 em0: Hardware Initialization Failedem0: Unable to initialize the hardware device_attach: em0 attach returned 5 pcib3: <ACPI PCI-PCI bridge> at device 7.0 on pci2 pci3: <ACPI PCI bus> on pcib3 pcib4: <PCI-PCI bridge> at device 0.0 on pci3 pci4: <PCI bus> on pcib4 amr0: <LSILogic MegaRAID 1.51> mem 0xf0000000-0xf7ffffff irq 16 at device 0.0 on pci4 amr0: <LSILogic PERC 3/DC> Firmware 161J, BIOS 3.17, 128MB RAM pci3: <mass storage, SCSI> at device 1.0 (no driver attached) fdc0: <floppy drive controller> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0 fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 psm: keyboard controller failed. sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A, console sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled orm0: <ISA Option ROMs> at iomem 0xc8000-0xc8fff,0xc0000-0xc7fff on isa0 pmtimer0 on isa0 ppc0: parallel port not found. sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounters tick every 10.000 msec amrd0: <LSILogic MegaRAID logical drive> on amr0 amrd0: 34556MB (70770688 sectors) RAID 5 (optimal) ses0 at amr0 bus 0 target 6 lun 0 ses0: <DELL 1x3 U2W SCSI BP 5.12> Fixed Processor SCSI-2 device ses0: SAF-TE Compliant Device SMP: AP CPU #1 Launched! SMP: AP CPU #2 Launched! SMP: AP CPU #3 Launched! Mounting root from ufs:/dev/amrd0s1a Pre-seeding PRNG: kickstart. Loading configuration files. Entropy harvesting: interrupts ethernet point_to_point kickstart. swapon: adding /dev/amrd0s1b as swap device Starting file system checks: /dev/amrd0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/amrd0s1a: clean, 220341 free (661 frags, 27460 blocks, 0.3% fragmentation) /dev/amrd0s1e: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/amrd0s1e: clean, 506481 free (41 frags, 63305 blocks, 0.0% fragmentation) /dev/amrd0s1f: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/amrd0s1f: clean, 11257854 free (34774 frags, 1402885 blocks, 0.3% fragmentation) /dev/amrd0s1d: FILE SYSTEM CLEAN; SKIPPING CHECKS /dev/amrd0s1d: clean, 2528867 free (387 frags, 316060 blocks, 0.0% fragmentation) Setting hostname: hippo.sentex.ca. lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 Additional routing options: IP gateway=YES. Starting devd. Mounting NFS file systems:. Starting syslogd. ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/X11R6/lib /usr/local/lib a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout /usr/X11R6/lib/aout Recovering vi editor sessions:. Starting local daemons:. Updating motd. Configuring syscons: blanktime. Starting sshd. Initial i386 initialization:. Additional ABI support:. Starting cron. Local package initialization:. Additional TCP options:.Received on Wed Jul 06 2005 - 19:20:41 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:38 UTC