Søren, Maybe this problem isn't yours.... I spent this afternoon and booted a 5.4 FixIt CD and pull the information from the mirror array (which worked). I removed the array from the SIS 180 RAID controller and reconfigured it as simply JBOD. I thought I would see my two drives available and switch to gmirror, alas it doesn't work. Even the BTX loader at the begnning only sees disk0-2 while the v5.4 BTX loader sees disk0-5. v6.0-RC1 does not even see the SATA drives hanging off the SIS 180 RAID controller, but it does see the controller. I've even removed Hyper-Threading (no change) and checked the BIOS for some kind of compatibility mode, but none exists. Please advise if I should actually open a ticket regarding this issue. Thanks! The following is my latest boot attempt w/JBOD instead of RAID-0 .... ======================================== Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 6.0-RC1 #0: Sat Oct 15 13:32:44 EDT 2005 root_at_mercury.kingsquarry.net:/usr/obj/usr/src/sys/GENERIC ACPI APIC Table: <RS300 AWRDACPI> Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3006.90-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf34 Stepping = 4 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x441d<SSE3,RSVD2,MON,DS_CPL,CNTX-ID,<b14>> Hyperthreading: 2 logical CPUs real memory = 535756800 (510 MB) avail memory = 514928640 (491 MB) ioapic0: Changing APIC ID to 2 ioapic0 <Version 1.1> irqs 0-23 on motherboard npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <RS300 AWRDACPI> on motherboard acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21 acpi0: Power Button (fixed) pci_link0: <ACPI PCI Link LNKA> irq 0 on acpi0 pci_link1: <ACPI PCI Link LNKB> irq 0 on acpi0 pci_link2: <ACPI PCI Link LNKC> irq 0 on acpi0 pci_link3: <ACPI PCI Link LNKD> irq 0 on acpi0 Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 cpu0: <ACPI CPU> on acpi0 acpi_throttle0: <ACPI CPU Throttling> on cpu0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pci1: <display, VGA> at device 5.0 (no driver attached) skc0: <Marvell Gigabit Ethernet> port 0xe400-0xe4ff mem 0xe1000000-0xe1003fff irq 19 at device 13.0 on pci0 skc0: Marvell Yukon Lite Gigabit Ethernet rev. A3(0x7) sk0: <Marvell Semiconductor, Inc. Yukon> on skc0 sk0: Ethernet address: 00:11:2f:9e:f6:f0 miibus0: <MII bus> on sk0 e1000phy0: <Marvell 88E1000 Gigabit PHY> on miibus0 e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto ohci0: <OHCI (generic) USB controller> mem 0xe1004000-0xe1004fff irq 19 at device 19.0 on pci0 ohci0: [GIANT-LOCKED] usb0: OHCI version 1.0, legacy support usb0: SMM does not respond, resetting usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: (0x1002) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 3 ports with 3 removable, self powered ohci1: <OHCI (generic) USB controller> mem 0xe1005000-0xe1005fff irq 19 at device 19.1 on pci0 ohci1: [GIANT-LOCKED] usb1: OHCI version 1.0, legacy support usb1: SMM does not respond, resetting usb1: <OHCI (generic) USB controller> on ohci1 usb1: USB revision 1.0 uhub1: (0x1002) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 3 ports with 3 removable, self powered ehci0: <EHCI (generic) USB 2.0 controller> mem 0xe1006000-0xe1006fff irq 19 at device 19.2 on pci0 ehci0: [GIANT-LOCKED] usb2: EHCI version 1.0 usb2: companion controllers, 3 ports each: usb0 usb1 usb2: <EHCI (generic) USB 2.0 controller> on ehci0 usb2: USB revision 2.0 uhub2: (0x1002) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub2: 6 ports with 6 removable, self powered pci0: <serial bus, SMBus> at device 20.0 (no driver attached) atapci0: <ATI IXP200 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 20.1 on pci0 ata0: <ATA channel 0> on atapci0 ata1: <ATA channel 1> on atapci0 isab0: <PCI-ISA bridge> at device 20.3 on pci0 isa0: <ISA bus> on isab0 pcib2: <ACPI PCI-PCI bridge> at device 20.4 on pci0 pci2: <ACPI PCI bus> on pcib2 fwohci0: <VIA Fire II (VT6306)> port 0xc000-0xc07f mem 0xe0000000-0xe00007ff irq 17 at device 9.0 on pci2 fwohci0: OHCI version 1.0 (ROM=1) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:e0:18:00:00:a2:7f:e5 fwohci0: Phy 1394a available S400, 2 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:e0:18:a2:7f:e5 fwe0: Ethernet address: 02:e0:18:a2:7f:e5 fwe0: if_start running deferred for Giant sbp0: <SBP-2/SCSI over FireWire> on firewire0 fwohci0: Initiate bus reset fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) atapci1: <SiS 180 SATA150 controller> port 0xc400-0xc407,0xc800-0xc803,0xcc00-0xcc07,0xd000-0xd003,0xd400-0xd40f irq 18 at device 10.0 on pci2 ata2: <ATA channel 0> on atapci1 ata3: <ATA channel 1> on atapci1 pci0: <multimedia, audio> at device 20.5 (no driver attached) acpi_tz0: <Thermal Zone> on acpi0 fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: [FAST] sio0: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 flags 0x10 on acpi0 sio0: type 16550A sio1: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0 sio1: type 16550A atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model Generic PS/2 mouse, device ID 0 pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xcc000-0xcffff,0xd0000-0xd3fff on isa0 ppc0: parallel port not found. sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 3006903735 Hz quality 800 Timecounters tick every 1.000 msec ad0: 76319MB <WDC WD800BB-22JHA0 05.01C05> at ata0-master UDMA100 ad2: DMA limited to UDMA33, device found non-ATA66 cable ad2: 76319MB <WDC WD800BB-22JHA0 05.01C05> at ata1-master UDMA33 acd0: CDROM <CD-56E/3.0D> at ata1-slave PIO3 Trying to mount root from ufs:/dev/ad0s1a ======================================== Thanks! - Jeff Jeff Doolittle wrote: > Søren, > > This post is almost identical to my original request for help on 10/13. > > I've upgrade one of my machines from 5.4-stable to 6.0-RC1 and the Sis > 180 RAID mirror is no longer recognized. The worked perfectly in > 5.4.... Attached below is the output from the dmesg based on a World > / Generic kernel cvsup'd today: > > ======================================== > > Copyright (c) 1992-2005 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 6.0-RC1 #0: Sat Oct 15 13:32:44 EDT 2005 > root_at_mercury.kingsquarry.net:/usr/obj/usr/src/sys/GENERIC > ACPI APIC Table: <RS300 AWRDACPI> > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz (3006.86-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0xf34 Stepping = 4 > > Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> > > Features2=0x441d<SSE3,RSVD2,MON,DS_CPL,CNTX-ID,<b14>> > Hyperthreading: 2 logical CPUs > real memory = 535756800 (510 MB) > avail memory = 514928640 (491 MB) > ioapic0: Changing APIC ID to 2 > ioapic0 <Version 1.1> irqs 0-23 on motherboard > npx0: [FAST] > npx0: <math processor> on motherboard > npx0: INT 16 interface > acpi0: <RS300 AWRDACPI> on motherboard > acpi0: Overriding SCI Interrupt from IRQ 9 to IRQ 21 > acpi0: Power Button (fixed) > pci_link0: <ACPI PCI Link LNKA> irq 0 on acpi0 > pci_link1: <ACPI PCI Link LNKB> irq 0 on acpi0 > pci_link2: <ACPI PCI Link LNKC> irq 0 on acpi0 > pci_link3: <ACPI PCI Link LNKD> irq 0 on acpi0 > Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 > acpi_timer0: <32-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 > cpu0: <ACPI CPU> on acpi0 > acpi_throttle0: <ACPI CPU Throttling> on cpu0 > acpi_button0: <Power Button> on acpi0 > pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > pci0: <ACPI PCI bus> on pcib0 > pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 > pci1: <ACPI PCI bus> on pcib1 > pci1: <display, VGA> at device 5.0 (no driver attached) > skc0: <Marvell Gigabit Ethernet> port 0xe400-0xe4ff mem > 0xe1000000-0xe1003fff irq 19 at device 13.0 on pci0 > skc0: Marvell Yukon Lite Gigabit Ethernet rev. A3(0x7) > sk0: <Marvell Semiconductor, Inc. Yukon> on skc0 > sk0: Ethernet address: 00:11:2f:9e:f6:f0 > miibus0: <MII bus> on sk0 > e1000phy0: <Marvell 88E1000 Gigabit PHY> on miibus0 > e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, > 1000baseTX-FDX, auto > ohci0: <OHCI (generic) USB controller> mem 0xe1004000-0xe1004fff irq > 19 at device 19.0 on pci0 > ohci0: [GIANT-LOCKED] > usb0: OHCI version 1.0, legacy support > usb0: SMM does not respond, resetting > usb0: <OHCI (generic) USB controller> on ohci0 > usb0: USB revision 1.0 > uhub0: (0x1002) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub0: 3 ports with 3 removable, self powered > ohci1: <OHCI (generic) USB controller> mem 0xe1005000-0xe1005fff irq > 19 at device 19.1 on pci0 > ohci1: [GIANT-LOCKED] > usb1: OHCI version 1.0, legacy support > usb1: SMM does not respond, resetting > usb1: <OHCI (generic) USB controller> on ohci1 > usb1: USB revision 1.0 > uhub1: (0x1002) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 > uhub1: 3 ports with 3 removable, self powered > ehci0: <EHCI (generic) USB 2.0 controller> mem 0xe1006000-0xe1006fff > irq 19 at device 19.2 on pci0 > ehci0: [GIANT-LOCKED] > usb2: EHCI version 1.0 > usb2: companion controllers, 3 ports each: usb0 usb1 > usb2: <EHCI (generic) USB 2.0 controller> on ehci0 > usb2: USB revision 2.0 > uhub2: (0x1002) EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 > uhub2: 6 ports with 6 removable, self powered > pci0: <serial bus, SMBus> at device 20.0 (no driver attached) > atapci0: <ATI IXP200 UDMA100 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 20.1 on pci0 > ata0: <ATA channel 0> on atapci0 > ata1: <ATA channel 1> on atapci0 > isab0: <PCI-ISA bridge> at device 20.3 on pci0 > isa0: <ISA bus> on isab0 > pcib2: <ACPI PCI-PCI bridge> at device 20.4 on pci0 > pci2: <ACPI PCI bus> on pcib2 > fwohci0: <VIA Fire II (VT6306)> port 0xc000-0xc07f mem > 0xe0000000-0xe00007ff irq 17 at device 9.0 on pci2 > fwohci0: OHCI version 1.0 (ROM=1) > fwohci0: No. of Isochronous channels is 4. > fwohci0: EUI64 00:e0:18:00:00:a2:7f:e5 > fwohci0: Phy 1394a available S400, 2 ports. > fwohci0: Link S400, max_rec 2048 bytes. > firewire0: <IEEE1394(FireWire) bus> on fwohci0 > fwe0: <Ethernet over FireWire> on firewire0 > if_fwe0: Fake Ethernet address: 02:e0:18:a2:7f:e5 > fwe0: Ethernet address: 02:e0:18:a2:7f:e5 > fwe0: if_start running deferred for Giant > sbp0: <SBP-2/SCSI over FireWire> on firewire0 > fwohci0: Initiate bus reset > fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode > firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) > firewire0: bus manager 0 (me) > atapci1: <SiS 180 SATA150 controller> port > 0xc400-0xc407,0xc800-0xc803,0xcc00-0xcc07,0xd000-0xd003,0xd400-0xd40f > irq 18 at device 10.0 on pci2 > ata2: <ATA channel 0> on atapci1 > ata3: <ATA channel 1> on atapci1 > pci0: <multimedia, audio> at device 20.5 (no driver attached) > acpi_tz0: <Thermal Zone> on acpi0 > fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on > acpi0 > fdc0: [FAST] > sio0: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 flags 0x10 > on acpi0 > sio0: type 16550A > sio1: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0 > sio1: type 16550A > atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 > atkbd0: <AT Keyboard> irq 1 on atkbdc0 > kbd0 at atkbd0 > atkbd0: [GIANT-LOCKED] > psm0: <PS/2 Mouse> irq 12 on atkbdc0 > psm0: [GIANT-LOCKED] > psm0: model VersaPad, device ID 0 > pmtimer0 on isa0 > orm0: <ISA Option ROMs> at iomem 0xcc000-0xcffff,0xd0000-0xd3fff on isa0 > ppc0: parallel port not found. > sc0: <System console> at flags 0x100 on isa0 > sc0: VGA <16 virtual consoles, flags=0x300> > vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 > Timecounter "TSC" frequency 3006859935 Hz quality 800 > Timecounters tick every 1.000 msec > ad0: 76319MB <WDC WD800BB-22JHA0 05.01C05> at ata0-master UDMA100 > ad2: DMA limited to UDMA33, device found non-ATA66 cable > ad2: 76319MB <WDC WD800BB-22JHA0 05.01C05> at ata1-master UDMA33 > acd0: CDROM <CD-56E/3.0D> at ata1-slave PIO3 > Trying to mount root from ufs:/dev/ad0s1a > > ======================================== > > As you can see the SiS 180 is recognized and it's associated SATA > controllers (ata2 /ata3) but the ar0 device is never created. > > I've checked UPDATING but didn't see any comments about existing RAID > support being removed so I assume there must be a bug. > > Thank you! > > - Jeff > > _______________________________________________ > freebsd-current_at_freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to > "freebsd-current-unsubscribe_at_freebsd.org"Received on Sun Oct 16 2005 - 19:35:43 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:45 UTC