I try to enable touchpad support on an Acer Travelmate 8104 by setting hw.psm.synaptics_support="1" in loader.conf. After that any access to psm0 seems to hang the machine solid. For instance running 'moused -p /dev/psm0' or starting Xorg with psm0 as mousedevice freezes the machine immediately, and I have to use the power button to recover. This is an out-of-the-box 6.0RC1 Generic kernel. The only other change I've done is to disable acpi, though that doesn't change anything regarding the touchpad problem. Is anyone else seeing something similar (and preferably have a solution)? Output of dmesg is found below. -tom Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 6.0-RC1 #0: Sun Oct 9 20:32:57 UTC 2005 root_at_x64.samsco.home:/usr/obj/usr/src/sys/GENERIC Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) M processor 2.00GHz (1995.02-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6d8 Stepping = 8 Features=0xafe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE> Features2=0x180<EST,TM2> AMD Features=0x100000<NX> real memory = 1072168960 (1022 MB) avail memory = 1040318464 (992 MB) npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface cpu0 on motherboard pcib0: <Host to PCI bridge> pcibus 0 on motherboard pci0: <PCI bus> on pcib0 pcib1: <PCI-PCI bridge> irq 10 at device 1.0 on pci0 pci1: <PCI bus> on pcib1 pci1: <display, VGA> at device 0.0 (no driver attached) pci0: <multimedia> at device 27.0 (no driver attached) pcib2: <PCI-PCI bridge> irq 10 at device 28.0 on pci0 pci9: <PCI bus> on pcib2 pcib3: <PCI-PCI bridge> irq 10 at device 28.1 on pci0 pci10: <PCI bus> on pcib3 pcib4: <PCI-PCI bridge> irq 11 at device 28.2 on pci0 pci2: <PCI bus> on pcib4 uhci0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> port 0x1800-0x181f irq 11 at device 29.0 on pci0 uhci0: [GIANT-LOCKED] usb0: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-A> on uhci0 usb0: USB revision 1.0 uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> port 0x1820-0x183f irq 11 at device 29.1 on pci0 uhci1: [GIANT-LOCKED] usb1: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-B> on uhci1 usb1: USB revision 1.0 uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered uhci2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> port 0x1840-0x185f irq 11 at device 29.2 on pci0 uhci2: [GIANT-LOCKED] usb2: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-C> on uhci2 usb2: USB revision 1.0 uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub2: 2 ports with 2 removable, self powered uhci3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> port 0x1860-0x187f irq 10 at device 29.3 on pci0 uhci3: [GIANT-LOCKED] usb3: <Intel 82801FB/FR/FW/FRW (ICH6) USB controller USB-D> on uhci3 usb3: USB revision 1.0 uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub3: 2 ports with 2 removable, self powered ehci0: <EHCI (generic) USB 2.0 controller> mem 0xc8004000-0xc80043ff irq 11 at device 29.7 on pci0 ehci0: [GIANT-LOCKED] usb4: EHCI version 1.0 usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4: <EHCI (generic) USB 2.0 controller> on ehci0 usb4: USB revision 2.0 uhub4: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub4: 8 ports with 8 removable, self powered pcib5: <PCI-PCI bridge> at device 30.0 on pci0 pci6: <PCI bus> on pcib5 pci6: <network> at device 3.0 (no driver attached) bge0: <Broadcom BCM5788 Gigabit Ethernet, ASIC rev. 0x3003> mem 0xc8200000-0xc820ffff irq 10 at device 6.0 on pci6 miibus0: <MII bus> on bge0 brgphy0: <BCM5705 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge0: Ethernet address: 00:c0:9f:c0:73:7a fwohci0: <Texas Instruments TSB43AB21/A/AI/A-EP> mem 0xc8215000-0xc82157ff,0xc8210000-0xc8213fff irq 11 at device 7.0 on pci6 fwohci0: OHCI version 1.10 (ROM=1) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:c0:9f:00:00:67:04:ee fwohci0: Phy 1394a available S400, 1 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:c0:9f:67:04:ee fwe0: Ethernet address: 02:c0:9f:67:04:ee fwe0: if_start running deferred for Giant sbp0: <SBP-2/SCSI over FireWire> on firewire0 fwohci0: Initiate bus reset fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) cbb0: <PCI-CardBus Bridge> mem 0xc8216000-0xc8216fff irq 11 at device 9.0 on pci6 cardbus0: <CardBus bus> on cbb0 pccard0: <16-bit PCCard bus> on cbb0 cbb1: <PCI-CardBus Bridge> mem 0xc8217000-0xc8217fff irq 10 at device 9.1 on pci6 cardbus1: <CardBus bus> on cbb1 pccard1: <16-bit PCCard bus> on cbb1 pci6: <base peripheral> at device 9.2 (no driver attached) cbb2: <PCI-CardBus Bridge> at device 9.3 on pci6 cardbus2: <CardBus bus> on cbb2 pccard2: <16-bit PCCard bus> on cbb2 cbb: Unable to map IRQ... device_attach: cbb2 attach returned 12 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH6 SATA150 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x18a0-0x18af at device 31.2 on pci0 atapci0: failed to enable memory mapping! ata0: <ATA channel 0> on atapci0 ata1: <ATA channel 1> on atapci0 pci0: <serial bus, SMBus> at device 31.3 (no driver attached) pmtimer0 on isa0 orm0: <ISA Option ROM> at iomem 0xe0000-0xe17ff on isa0 atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model Synaptics Touchpad, device ID 0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 or not responding sio1 at port 0x2f8-0x2ff irq 3 on isa0 sio1: type 16550A vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 unknown: <PNP0303> can't assign resources (port) unknown: <INT0800> can't assign resources (memory) unknown: <PNP0c02> can't assign resources (memory) unknown: <PNP0f13> can't assign resources (irq) unknown: <HWPc224> can't assign resources (port) ppc1: parallel port not found. ugen0: Broadcom BCM2035, rev 1.10/1.00, addr 2 Timecounter "TSC" frequency 1995015913 Hz quality 800 Timecounters tick every 1.000 msec ad0: 95396MB <Seagate ST9100823A 3.01> at ata0-master SATA150 acd0: FAILURE - MODE_SENSE_BIG timed out acd0: DVDR <HL-DT-ST DVDRAM GMA-4080N/0H35> at ata1-master UDMA33 Trying to mount root from ufs:/dev/ad0s2a bge0: link state changed to UPReceived on Mon Oct 31 2005 - 13:53:38 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:46 UTC