> ...apparently the attachments got lost... ...and just did once Again? Must be the list software not liking them. I'll inline them: ----- dmesg start ----- Copyright (c) 1992-2005 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 6.0-BETA3 #0: Sat Sep 3 19:59:33 CEST 2005 maxlor_at_gaia.intranet:/usr/obj/usr/src/sys/GAIA ACPI APIC Table: <DELL PE600SC > Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2399.34-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0xf27 Stepping = 7 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x400<CNTX-ID> real memory = 268369920 (255 MB) avail memory = 253108224 (241 MB) ioapic0: Changing APIC ID to 1 ioapic1: Changing APIC ID to 2 ioapic2: Changing APIC ID to 3 MADT: Forcing active-low polarity and level trigger for SCI ioapic0 <Version 1.1> irqs 0-15 on motherboard ioapic1 <Version 1.1> irqs 16-31 on motherboard ioapic2 <Version 1.1> irqs 32-47 on motherboard npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <DELL PE600SC> on motherboard acpi0: Power Button (fixed) pci_link0: <ACPI PCI Link LNK0> on acpi0 pci_link1: <ACPI PCI Link LNK1> irq 10 on acpi0 pci_link2: <ACPI PCI Link LNK2> on acpi0 pci_link3: <ACPI PCI Link LNK3> on acpi0 pci_link4: <ACPI PCI Link LNK4> irq 5 on acpi0 pci_link5: <ACPI PCI Link LNK5> on acpi0 pci_link6: <ACPI PCI Link LNK6> on acpi0 pci_link7: <ACPI PCI Link LNK7> on acpi0 pci_link8: <ACPI PCI Link LNK8> on acpi0 pci_link9: <ACPI PCI Link LNK9> on acpi0 pci_link10: <ACPI PCI Link LNKA> on acpi0 pci_link11: <ACPI PCI Link LNKB> on acpi0 pci_link12: <ACPI PCI Link LNKC> on acpi0 pci_link13: <ACPI PCI Link LNKD> on acpi0 pci_link14: <ACPI PCI Link LNKE> on acpi0 pci_link15: <ACPI PCI Link LNKF> on acpi0 pci_link16: <ACPI PCI Link LN10> on acpi0 pci_link17: <ACPI PCI Link LN11> on acpi0 pci_link18: <ACPI PCI Link LN12> on acpi0 pci_link19: <ACPI PCI Link LN13> on acpi0 pci_link20: <ACPI PCI Link LN14> on acpi0 pci_link21: <ACPI PCI Link LN15> on acpi0 pci_link22: <ACPI PCI Link LN16> on acpi0 pci_link23: <ACPI PCI Link LN17> on acpi0 pci_link24: <ACPI PCI Link LN18> on acpi0 pci_link25: <ACPI PCI Link LN19> on acpi0 pci_link26: <ACPI PCI Link LN1A> on acpi0 pci_link27: <ACPI PCI Link LN1B> on acpi0 pci_link28: <ACPI PCI Link LN1C> on acpi0 pci_link29: <ACPI PCI Link LN1D> on acpi0 pci_link30: <ACPI PCI Link LN1E> on acpi0 pci_link31: <ACPI PCI Link LN1F> on acpi0 pci_link32: <ACPI PCI Link LUSB> irq 3 on acpi0 pci_link33: <ACPI PCI Link LTID> irq 11 on acpi0 Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000 acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 cpu0: <ACPI CPU> on acpi0 pcib0: <ACPI Host-PCI bridge> on acpi0 pci0: <ACPI PCI bus> on pcib0 em0: <Intel(R) PRO/1000 Network Connection, Version - 2.1.7> port 0xecc0-0xecff mem 0xfe100000-0xfe11ffff irq 17 at device 2.0 on pci0 em0: Ethernet address: 00:c0:9f:21:ac:ff em0: Speed:N/A Duplex:N/A amr0: <LSILogic MegaRAID 1.51> mem 0xfeb00000-0xfeb0ffff irq 20 at device 4.0 on pci0 amr0: <LSILogic PERC 3/SC> Firmware 1.78, BIOS 3.29, 32MB RAM pci0: <display, VGA> at device 8.0 (no driver attached) atapci0: <ServerWorks CSB6 UDMA66 controller> port 0x1e8-0x1ef,0x3ec-0x3ef,0x168-0x16f,0x36c-0x36f,0x900-0x90f irq 11 at device 14.0 on pci0 ata2: <ATA channel 0> on atapci0 ata3: <ATA channel 1> on atapci0 atapci1: <ServerWorks CSB6 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x8b0-0x8bf at device 15.1 on pci0 ata0: <ATA channel 0> on atapci1 ata1: <ATA channel 1> on atapci1 ohci0: <OHCI (generic) USB controller> mem 0xfe120000-0xfe120fff irq 3 at device 15.2 on pci0 ohci0: [GIANT-LOCKED] usb0: OHCI version 1.0, legacy support usb0: SMM does not respond, resetting usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: (0x1166) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered isab0: <PCI-ISA bridge> at device 15.3 on pci0 isa0: <ISA bus> on isab0 fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77f irq 7 drq 1 on acpi0 ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode ppc0: FIFO with 16/16/8 bytes threshold ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xec000-0xeffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 umass0: Western Digital Corporation Western Digital USB Hard Drive, rev 2.00/ff.ff, addr 2 Timecounter "TSC" frequency 2399338028 Hz quality 800 Timecounters tick every 1.000 msec acd0: CDROM <GCR-8481B/2.01> at ata2-master UDMA33 amrd0: <LSILogic MegaRAID logical drive> on amr0 amrd0: 34678MB (71020544 sectors) RAID 1 (optimal) da0 at umass-sim0 bus 0 target 0 lun 0 da0: <WDC WD800BB-00FRA0 77.0> Fixed Direct Access SCSI-2 device da0: 1.000MB/s transfers da0: 76319MB (156301488 512 byte sectors: 255H 63S/T 9729C) Trying to mount root from ufs:/dev/amrd0s2a p4tcc0: <CPU Frequency Thermal Control> on cpu0 ----- dmesg end ----- ----- kernel config start ----- machine i386 cpu I686_CPU ident GAIA # To statically compile in device wiring instead of /boot/device.hints #hints "GENERIC.hints" # Default places to look for devices. #makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols #options SCHED_ULE # ULE scheduler options SCHED_4BSD # 4BSD scheduler options PREEMPTION # Enable kernel thread preemption options INET # InterNETworking options INET6 # IPv6 communications protocols options FFS # Berkeley Fast Filesystem options SOFTUPDATES # Enable FFS soft updates support options UFS_ACL # Support for access control lists options UFS_DIRHASH # Improve performance on big directories options MD_ROOT # MD is a potential root device options NFSCLIENT # Network Filesystem Client options NFSSERVER # Network Filesystem Server options NFS_ROOT # NFS usable as /, requires NFSCLIENT options MSDOSFS # MSDOS Filesystem options CD9660 # ISO 9660 Filesystem options PROCFS # Process filesystem (requires PSEUDOFS) options PSEUDOFS # Pseudo-filesystem framework options GEOM_GPT # GUID Partition Tables. options COMPAT_43 # Compatible with BSD 4.3 [KEEP THIS!] options COMPAT_FREEBSD4 # Compatible with FreeBSD4 options COMPAT_FREEBSD5 # Compatible with FreeBSD5 options SCSI_DELAY=5000 # Delay (in ms) before probing SCSI options KTRACE # ktrace(1) support options SYSVSHM # SYSV-style shared memory options SYSVMSG # SYSV-style message queues options SYSVSEM # SYSV-style semaphores options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time extensions options KBD_INSTALL_CDEV # install a CDEV entry in /dev options AHC_REG_PRETTY_PRINT # Print register bitfields in debug # output. Adds ~128k to driver. options AHD_REG_PRETTY_PRINT # Print register bitfields in debug # output. Adds ~215k to driver. options ADAPTIVE_GIANT # Giant mutex is adaptive. # Debugging for use in -current #options KDB # Enable kernel debugger support. #options DDB # Support DDB. #options GDB # Support remote GDB. #options INVARIANTS # Enable calls of extra sanity checking #options INVARIANT_SUPPORT # Extra sanity checks of internal structures, required by INVARIANTS #options WITNESS # Enable checks to detect deadlocks and cycles #options WITNESS_SKIPSPIN # Don't run witness on spinlocks for speed # To make an SMP kernel, the next two lines are needed #options SMP # Symmetric MultiProcessor Kernel device apic # I/O APIC # Bus support. Do not remove isa, even if you have no isa slots device isa device eisa device pci # Floppy drives device fdc # ATA and ATAPI devices device ata device atadisk # ATA disk drives device ataraid # ATA RAID drives device atapicd # ATAPI CDROM drives device atapifd # ATAPI floppy drives device atapist # ATAPI tape drives options ATA_STATIC_ID # Static device numbering # SCSI Controllers #device ahb # EISA AHA1742 family #device ahc # AHA2940 and onboard AIC7xxx devices #device ahd # AHA39320/29320 and onboard AIC79xx devices #device amd # AMD 53C974 (Tekram DC-390(T)) #device isp # Qlogic family #device ispfw # Firmware for QLogic HBAs- normally a module #device mpt # LSI-Logic MPT-Fusion #device ncr # NCR/Symbios Logic #device sym # NCR/Symbios Logic (newer chipsets + those of `ncr') #device trm # Tekram DC395U/UW/F DC315U adapters #device adv # Advansys SCSI adapters #device adw # Advansys wide SCSI adapters #device aha # Adaptec 154x SCSI adapters #device aic # Adaptec 15[012]x SCSI adapters, AIC-6[23]60. #device bt # Buslogic/Mylex MultiMaster SCSI adapters #device ncv # NCR 53C500 #device nsp # Workbit Ninja SCSI-3 #device stg # TMC 18C30/18C50 # SCSI peripherals device scbus # SCSI bus (required for SCSI) device ch # SCSI media changers device da # Direct Access (disks) device sa # Sequential Access (tape etc) device cd # CD device pass # Passthrough device (direct SCSI access) device ses # SCSI Environmental Services (and SAF-TE) # RAID controllers interfaced to the SCSI subsystem device amr # AMI MegaRAID #device arcmsr # Areca SATA II RAID #device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID #device ciss # Compaq Smart RAID 5* #device dpt # DPT Smartcache III, IV - See NOTES for options #device hptmv # Highpoint RocketRAID 182x #device iir # Intel Integrated RAID #device ips # IBM (Adaptec) ServeRAID #device mly # Mylex AcceleRAID/eXtremeRAID #device twa # 3ware 9000 series PATA/SATA RAID # RAID controllers #device aac # Adaptec FSA RAID #device aacp # SCSI passthrough for aac (requires CAM) #device ida # Compaq Smart RAID #device mlx # Mylex DAC960 family #device pst # Promise Supertrak SX6000 #device twe # 3ware ATA RAID # atkbdc0 controls both the keyboard and the PS/2 mouse device atkbdc # AT keyboard controller device atkbd # AT keyboard device psm # PS/2 mouse device vga # VGA video card driver device splash # Splash screen and screen saver support # syscons is the default console driver, resembling an SCO console device sc # Enable this for the pcvt (VT220 compatible) console driver #device vt #options XSERVER # support for X server on a vt console #options FAT_CURSOR # start with block cursor device agp # support several AGP chipsets # Floating point support - do not disable. device npx # Power management support (see NOTES for more options) #device apm # Add suspend/resume support for the i8254. device pmtimer # PCCARD (PCMCIA) support # PCMCIA and cardbus bridge support #device cbb # cardbus (yenta) bridge #device pccard # PC Card (16-bit) bus #device cardbus # CardBus (32-bit) bus # Serial (COM) ports device sio # 8250, 16[45]50 based serial ports # Parallel port device ppc device ppbus # Parallel port bus (required) device lpt # Printer device plip # TCP/IP over parallel device ppi # Parallel port interface device #device vpo # Requires scbus and da # If you've got a "dumb" serial or parallel PCI card that is # supported by the puc(4) glue driver, uncomment the following # line to enable it (connects to the sio and/or ppc drivers): #device puc # PCI Ethernet NICs. #device de # DEC/Intel DC21x4x (``Tulip'') device em # Intel PRO/1000 adapter Gigabit Ethernet Card #device ixgb # Intel PRO/10GbE Ethernet Card #device txp # 3Com 3cR990 (``Typhoon'') #device vx # 3Com 3c590, 3c595 (``Vortex'') # PCI Ethernet NICs that use the common MII bus controller code. # NOTE: Be sure to keep the 'device miibus' line in order to use these NICs! #device miibus # MII bus support #device bfe # Broadcom BCM440x 10/100 Ethernet #device bge # Broadcom BCM570xx Gigabit Ethernet #device dc # DEC/Intel 21143 and various workalikes #device fxp # Intel EtherExpress PRO/100B (82557, 82558) #device lge # Level 1 LXT1001 gigabit Ethernet #device nge # NatSemi DP83820 gigabit Ethernet #device nve # nVidia nForce MCP on-board Ethernet Networking #device pcn # AMD Am79C97x PCI 10/100(precedence over 'lnc') #device re # RealTek 8139C+/8169/8169S/8110S #device rl # RealTek 8129/8139 #device sf # Adaptec AIC-6915 (``Starfire'') #device sis # Silicon Integrated Systems SiS 900/SiS 7016 #device sk # SysKonnect SK-984x & SK-982x gigabit Ethernet #device ste # Sundance ST201 (D-Link DFE-550TX) #device ti # Alteon Networks Tigon I/II gigabit Ethernet #device tl # Texas Instruments ThunderLAN #device tx # SMC EtherPower II (83c170 ``EPIC'') #device vge # VIA VT612x gigabit Ethernet #device vr # VIA Rhine, Rhine II #device wb # Winbond W89C840F #device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'') # ISA Ethernet NICs. pccard NICs included. #device cs # Crystal Semiconductor CS89x0 NIC # 'device ed' requires 'device miibus' #device ed # NE[12]000, SMC Ultra, 3c503, DS8390 cards #device ex # Intel EtherExpress Pro/10 and Pro/10+ #device ep # Etherlink III based cards #device fe # Fujitsu MB8696x based cards #device ie # EtherExpress 8/16, 3C507, StarLAN 10 etc. #device lnc # NE2100, NE32-VL Lance Ethernet cards #device sn # SMC's 9000 series of Ethernet chips #device xe # Xircom pccard Ethernet # ISA devices that use the old ISA shims #device le # Wireless NIC cards #device wlan # 802.11 support #device an # Aironet 4500/4800 802.11 wireless NICs. #device awi # BayStack 660 and others #device ral # Ralink Technology RT2500 wireless NICs. #device wi # WaveLAN/Intersil/Symbol 802.11 wireless NICs. #device wl # Older non 802.11 Wavelan wireless NIC. # Pseudo devices. device loop # Network loopback device mem # Memory and kernel memory devices device io # I/O device device random # Entropy device device ether # Ethernet support #device sl # Kernel SLIP #device ppp # Kernel PPP device tun # Packet tunnel. device pty # Pseudo-ttys (telnet etc) device md # Memory "disks" device gif # IPv6 and IPv4 tunneling device faith # IPv6-to-IPv4 relaying (translation) # The `bpf' device enables the Berkeley Packet Filter. # Be aware of the administrative consequences of enabling this! # Note that 'bpf' is required for DHCP. device bpf # Berkeley packet filter # USB support device uhci # UHCI PCI->USB interface device ohci # OHCI PCI->USB interface device ehci # EHCI PCI->USB interface (USB 2.0) device usb # USB Bus (required) #device udbp # USB Double Bulk Pipe devices device ugen # Generic device uhid # "Human Interface Devices" device ukbd # Keyboard device ulpt # Printer device umass # Disks/Mass storage - Requires scbus and da device ums # Mouse #device ural # Ralink Technology RT2500USB wireless NICs #device urio # Diamond Rio 500 MP3 player #device uscanner # Scanners # USB Ethernet, requires miibus #device aue # ADMtek USB Ethernet #device axe # ASIX Electronics USB Ethernet #device cdce # Generic USB over Ethernet #device cue # CATC USB Ethernet #device kue # Kawasaki LSI USB Ethernet #device rue # RealTek RTL8150 USB Ethernet # FireWire support #device firewire # FireWire bus code #device sbp # SCSI over FireWire (Requires scbus and da) #device fwe # Ethernet over FireWire (non-standard!) options ATKBD_DFLT_KEYMAP makeoptions ATKBD_DFLT_KEYMAP=us.dvorak options SC_HISTORY_SIZE=1000 ----- kernel config end -----
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:42 UTC