Hi, from few days Current to today morning Current, if load atapicam in boot time system freeze, after some minutes repeats: acd0: req=0xc5b10524 TEST_UNIT_READY semaphore timeout !! DANGER Will Robinson !! after about half hour system continues boot. /var/log/messages output Copyright (c) 1992-2006 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 7.0-CURRENT #0: Tue Jan 24 04:43:14 MSK 2006 root_at_sam.vvt:/usr/src/sys/i386/compile/SAM acpi_alloc_wakeup_handler: can't alloc wake memory Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: AMD Athlon(tm) 64 Processor 3000+ (1809.28-MHz 686-class CPU) Origin = "AuthenticAMD" Id = 0x20ff2 Stepping = 2 Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2> Features2=0x1<SSE3> AMD Features=0xe2500800<SYSCALL,NX,MMX+,FFXSR,LM,3DNow+,3DNow> AMD Features2=0x1<LAHF> real memory = 1073676288 (1023 MB) avail memory = 1041211392 (992 MB) ACPI APIC Table: <Nvidia AWRDACPI> ioapic0 <Version 1.1> irqs 0-23 on motherboard lockmgr: thread 0xc09dbe40 unlocking unheld lock netsmb_dev: loaded npx0: [FAST] npx0: <math processor> on motherboard npx0: INT 16 interface acpi0: <Nvidia AWRDACPI> on motherboard acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR acpi0: Power Button (fixed) acpi_bus_number: can't get _ADR acpi_bus_number: can't get _ADR Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 cpu0: <ACPI CPU> on acpi0 acpi_throttle0: <ACPI CPU Throttling> on cpu0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: <memory> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 1.0 on pci0 isa0: <ISA bus> on isab0 pci0: <serial bus, SMBus> at device 1.1 (no driver attached) ohci0: <OHCI (generic) USB controller> mem 0xd2104000-0xd2104fff irq 21 at device 2.0 on pci0 ohci0: [GIANT-LOCKED] usb0: OHCI version 1.0, legacy support usb0: SMM does not respond, resetting usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 8 ports with 8 removable, self powered ehci0: <NVIDIA nForce4 USB 2.0 controller> mem 0xd2105000-0xd21050ff irq 22 at device 2.1 on pci0 ehci0: [GIANT-LOCKED] usb1: EHCI version 1.0 usb1: companion controller, 4 ports each: usb0 usb1: <NVIDIA nForce4 USB 2.0 controller> on ehci0 usb1: USB revision 2.0 uhub1: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1 uhub1: 8 ports with 8 removable, self powered pcm0: <nVidia nForce4> port 0xdc00-0xdcff,0xe000-0xe0ff mem 0xd2103000-0xd2103fff irq 23 at device 4.0 on pci0 pcm0: <Avance Logic ALC655 AC97 Codec> atapci0: <nVidia nForce CK804 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 6.0 on pci0 ata0: <ATA channel 0> on atapci0 ata1: <ATA channel 1> on atapci0 atapci1: <nVidia nForce CK804 SATA300 controller> port 0x9f0-0x9f7,0xbf0-0xbf3,0x970-0x977,0xb70-0xb73,0xd800-0xd80f mem 0xd2102000-0xd2102fff irq 21 at device 7.0 on pci0 ata2: <ATA channel 0> on atapci1 ata3: <ATA channel 1> on atapci1 atapci2: <nVidia nForce CK804 SATA300 controller> port 0x9e0-0x9e7,0xbe0-0xbe3,0x960-0x967,0xb60-0xb63,0xc400-0xc40f mem 0xd2101000-0xd2101fff irq 22 at device 8.0 on pci0 ata4: <ATA channel 0> on atapci2 ata5: <ATA channel 1> on atapci2 pcib1: <ACPI PCI-PCI bridge> at device 9.0 on pci0 pci5: <ACPI PCI bus> on pcib1 fwohci0: <VIA Fire II (VT6306)> port 0xa000-0xa07f mem 0xd2000000-0xd20007ff irq 19 at device 2.0 on pci5 fwohci0: OHCI version 1.0 (ROM=1) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:11:d8:00:00:4a:69:61 fwohci0: Phy 1394a available S400, 2 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:11:d8:4a:69:61 fwe0: Ethernet address: 02:11:d8:4a:69:61 fwe0: if_start running deferred for Giant sbp0: <SBP-2/SCSI over FireWire> on firewire0 fwohci0: Initiate bus reset fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) emu10kx0: <Creative SBLive! 5.1 Digital [SB0220]> port 0xa400-0xa41f irq 18 at device 5.0 on pci5 pcm1: <EMU10Kx PCM Interface> on emu10kx0 pcm1: <eMicro EM28028 AC97 Codec> pci5: <input device> at device 5.1 (no driver attached) nve0: <NVIDIA nForce MCP9 Networking Adapter> port 0xb000-0xb007 mem 0xd2100000-0xd2100fff irq 23 at device 10.0 on pci0 nve0: Ethernet address 00:13:d4:53:33:da miibus0: <MII bus> on nve0 rlphy0: <RTL8201L 10/100 media interface> on miibus0 rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto nve0: Ethernet address: 00:13:d4:53:33:da pcib2: <ACPI PCI-PCI bridge> at device 11.0 on pci0 pci4: <ACPI PCI bus> on pcib2 pcib3: <ACPI PCI-PCI bridge> at device 12.0 on pci0 pci3: <ACPI PCI bus> on pcib3 pcib4: <ACPI PCI-PCI bridge> at device 13.0 on pci0 pci2: <ACPI PCI bus> on pcib4 pcib5: <ACPI PCI-PCI bridge> at device 14.0 on pci0 pci1: <ACPI PCI bus> on pcib5 vgapci0: <VGA-compatible display> port 0x9000-0x90ff mem 0xc0000000-0xcfffffff,0xd1000000-0xd100ffff irq 18 at device 0.0 on p ci1 drm0: <ATI Radeon RV370 X300SE> on vgapci0 info: [drm] Initialized radeon 1.19.0 20050911 vgapci1: <VGA-compatible display> mem 0xd1010000-0xd101ffff at device 0.1 on pci1 acpi_tz0: <Thermal Zone> on acpi0 fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc0: [FAST] fd0: <1440-KB 3.5" drive> on fdc0 drive 0 sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 sio0: type 16550A ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode ppbus0: <Parallel port bus> on ppc0 plip0: <PLIP network interface> on ppbus0 lpt0: <Printer> on ppbus0 lpt0: Interrupt-driven port ppi0: <Parallel I/O> on ppbus0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] psm0: <PS/2 Mouse> irq 12 on atkbdc0 psm0: [GIANT-LOCKED] psm0: model IntelliMouse, device ID 3 pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xcffff,0xd0000-0xd3fff pnpid ORM0000 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Timecounter "TSC" frequency 1809281080 Hz quality 800 Timecounters tick every 1.000 msec ipfw2 (+ipv6) initialized, divert loadable, rule-based forwarding enabled, default to deny, logging limited to 50000 packets/e ntry by default ad0: 114473MB <Seagate ST3120026A 3.06> at ata0-master UDMA100 acd0: DVDR <BENQ DVD DD DW1640/BSLB> at ata1-slave UDMA33 ************************ Freeze there ************************** acd0: req=0xc5b10524 TEST_UNIT_READY semaphore timeout !! DANGER Will Robinson !! acd0: req=0xc5b10524 TEST_UNIT_READY semaphore timeout !! DANGER Will Robinson !! cd0 at ata1 bus 0 target 1 lun 0 cd0: <BENQ DVD DD DW1640 BSLB> Removable CD-ROM SCSI-0 device cd0: 33.000MB/s transfers cd0: H\^L\^F?-+\^F??A\^F??W\^F?H+\^[?\^SW+?\^P cam_periph_alloc: attempt to re-allocate valid device cd0 rejected cdasync: Unable to attach new device due to status 0x6 cam_periph_alloc: attempt to re-allocate valid device pass0 rejected passasync: Unable to attach new device due to status 0x6: CCB request was invalid Trying to mount root from ufs:/dev/ad0s1a -- Best regards, Andrey mailto:samspeedu_at_mail.ruReceived on Tue Jan 24 2006 - 07:21:46 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:38:51 UTC