I updated two boxes to recent kernels from a kernel around October 7 or so, and they now both hang on boot if I have a Neterion 10gbps ethernet card in the PCIe slot. Since I don't have the driver loaded at boot, it seems more likely it's a kernel bug. Both identical machines now have the following vpd warning during boot, which wasn't present previously, but may be unrelated: miibus0: <MII bus> on bge0 brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge0: Ethernet address: 00:17:a4:ff:79:0d pcib3: <ACPI PCI-PCI bridge> at device 13.0 on pci0 pci3: <ACPI PCI bus> on pcib3 pci3:0:0: bad VPD cksum, remain 14 bge1: <Broadcom BCM5750 B1, ASIC rev. 0x4101> mem 0xca100000-0xca10ffff irq 19 at device 0.0 on pci3 miibus1: <MII bus> on bge1 ... Then they wedge here: ... pcib4: <ACPI PCI-PCI bridge> at device 14.0 on pci0 pci4: <ACPI PCI bus> on pcib4 pcib5: <ACPI Host-PCI bridge> on acpi0 pci128: <ACPI PCI bus> on pcib5 pcib6: <ACPI PCI-PCI bridge> at device 1.0 on pci128 pci129: <ACPI PCI bus> on pcib6 <hang> Complete boot -v until the point of unhappiness below. Robert N M Watson Computer Laboratory University of Cambridge OK boot -sv GDB: no debug ports present KDB: debugger backends: ddb KDB: current backend: ddb SMAP type=01 base=0000000000000000 len=0000000000098800 SMAP type=02 base=0000000000098800 len=0000000000007800 SMAP type=02 base=00000000000c2000 len=000000000003e000 SMAP type=01 base=0000000000100000 len=00000000bfe20000 SMAP type=03 base=00000000bff20000 len=0000000000009000 SMAP type=04 base=00000000bff29000 len=0000000000057000 SMAP type=02 base=00000000bff80000 len=0000000000080000 SMAP type=02 base=00000000d8000000 len=0000000000000400 SMAP type=02 base=00000000d8001000 len=0000000000000400 SMAP type=02 base=00000000e0000000 len=0000000010000000 SMAP type=02 base=00000000fec00000 len=0000000000000400 SMAP type=02 base=00000000fee00000 len=0000000000001000 SMAP type=02 base=00000000fff80000 len=0000000000080000 SMAP type=01 base=0000000100000000 len=0000000140000000 Copyright (c) 1992-2006 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.0-CURRENT #5: Tue Nov 14 06:33:45 GMT 2006 root_at_noisier.cam.watson.org:/usr/obj/usr/src/sys/GENERIC WARNING: WITNESS option enabled, expect reduced performance. Using 16 colors for the VM-PQ tuning (1024, 16) Preloaded elf kernel "/boot/kernel/kernel" at 0xffffffff80b67000. Calibrating clock(s) ... i8254 clock: 1193200 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 2210192952 Hz CPU: Dual Core AMD Opteron(tm) Processor 275 (2210.19-MHz K8-class CPU) Origin = "AuthenticAMD" Id = 0x20f12 Stepping = 2 Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT> Features2=0x1<SSE3> AMD Features=0xe2500800<SYSCALL,NX,MMX+,FFXSR,LM,3DNow!+,3DNow!> AMD Features2=0x3<LAHF,CMP> HTT bit cleared - FreeBSD does not have licensing issues requiring it. Cores per package: 2 L1 2MB data TLB: 8 entries, fully associative L1 2MB instruction TLB: 8 entries, fully associative L1 4KB data TLB: 32 entries, fully associative L1 4KB instruction TLB: 32 entries, fully associative L1 data cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L1 instruction cache: 64 kbytes, 64 bytes/line, 1 lines/tag, 2-way associative L2 2MB unified TLB: 0 entries, disabled/not present L2 4KB data TLB: 512 entries, 4-way associative L2 4KB instruction TLB: 512 entries, 4-way associative L2 unified cache: 1024 kbytes, 64 bytes/line, 1 lines/tag, 16-way associative usable memory = 8576610304 (8179 MB) Physical memory chunk(s): 0x0000000000001000 - 0x0000000000094fff, 606208 bytes (148 pages) 0x0000000000c69000 - 0x00000000bff1ffff, 3207294976 bytes (783031 pages) 0x0000000100000000 - 0x000000022f177fff, 5085036544 bytes (1241464 pages) avail memory = 8281690112 (7898 MB) INTR: Adding local APIC 0 as a target ACPI APIC Table: <PTLTD APIC > INTR: Adding local APIC 1 as a target INTR: Adding local APIC 2 as a target INTR: Adding local APIC 3 as a target FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 cpu2 (AP): APIC ID: 2 cpu3 (AP): APIC ID: 3 APIC: CPU 0 has ACPI ID 0 APIC: CPU 1 has ACPI ID 1 APIC: CPU 2 has ACPI ID 2 APIC: CPU 3 has ACPI ID 3 MADT: Found IO APIC ID 4, Interrupt 0 at 0xfec00000 ioapic0: Routing external 8259A's -> intpin 0 ioapic0: intpin 0 -> ExtINT (edge, high) ioapic0: intpin 1 -> ISA IRQ 1 (edge, high) ioapic0: intpin 2 -> ISA IRQ 2 (edge, high) ioapic0: intpin 3 -> ISA IRQ 3 (edge, high) ioapic0: intpin 4 -> ISA IRQ 4 (edge, high) ioapic0: intpin 5 -> ISA IRQ 5 (edge, high) ioapic0: intpin 6 -> ISA IRQ 6 (edge, high) ioapic0: intpin 7 -> ISA IRQ 7 (edge, high) ioapic0: intpin 8 -> ISA IRQ 8 (edge, high) ioapic0: intpin 9 -> ISA IRQ 9 (edge, high) ioapic0: intpin 10 -> ISA IRQ 10 (edge, high) ioapic0: intpin 11 -> ISA IRQ 11 (edge, high) ioapic0: intpin 12 -> ISA IRQ 12 (edge, high) ioapic0: intpin 13 -> ISA IRQ 13 (edge, high) ioapic0: intpin 14 -> ISA IRQ 14 (edge, high) ioapic0: intpin 15 -> ISA IRQ 15 (edge, high) ioapic0: intpin 16 -> PCI IRQ 16 (level, low) ioapic0: intpin 17 -> PCI IRQ 17 (level, low) ioapic0: intpin 18 -> PCI IRQ 18 (level, low) ioapic0: intpin 19 -> PCI IRQ 19 (level, low) ioapic0: intpin 20 -> PCI IRQ 20 (level, low) ioapic0: intpin 21 -> PCI IRQ 21 (level, low) ioapic0: intpin 22 -> PCI IRQ 22 (level, low) ioapic0: intpin 23 -> PCI IRQ 23 (level, low) MADT: Found IO APIC ID 5, Interrupt 24 at 0xd8000000 ioapic1: intpin 0 -> PCI IRQ 24 (level, low) ioapic1: intpin 1 -> PCI IRQ 25 (level, low) ioapic1: intpin 2 -> PCI IRQ 26 (level, low) ioapic1: intpin 3 -> PCI IRQ 27 (level, low) ioapic1: intpin 4 -> PCI IRQ 28 (level, low) ioapic1: intpin 5 -> PCI IRQ 29 (level, low) ioapic1: intpin 6 -> PCI IRQ 30 (level, low) MADT: Found IO APIC ID 6, Interrupt 31 at 0xd8001000 ioapic2: intpin 0 -> PCI IRQ 31 (level, low) ioapic2: intpin 1 -> PCI IRQ 32 (level, low) ioapic2: intpin 2 -> PCI IRQ 33 (level, low) ioapic2: intpin 3 -> PCI IRQ 34 (level, low) ioapic2: intpin 4 -> PCI IRQ 35 (level, low) ioapic2: intpin 5 -> PCI IRQ 36 (level, low) ioapic2: intpin 6 -> PCI IRQ 37 (level, low) MADT: Interrupt override: source 9, irq 9 ioapic0: intpin 9 trigger: level ioapic0: intpin 9 polarity: low ioapic1: Routing NMI -> intpin 4 ioapic2: Routing NMI -> intpin 4 lapic0: Routing NMI -> LINT1 lapic0: LINT1 trigger: edge lapic0: LINT1 polarity: high lapic1: Routing NMI -> LINT1 lapic1: LINT1 trigger: edge lapic1: LINT1 polarity: high lapic2: Routing NMI -> LINT1 lapic2: LINT1 trigger: edge lapic2: LINT1 polarity: high lapic3: Routing NMI -> LINT1 lapic3: LINT1 trigger: edge lapic3: LINT1 polarity: high ioapic0 <Version 1.1> irqs 0-23 on motherboard ioapic1 <Version 1.1> irqs 24-30 on motherboard ioapic2 <Version 1.1> irqs 31-37 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x00040010 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00000000 err: 0x00010000 pcm: 0x00010000 wlan: <802.11 Link Layer> ath_rate: version 1.2 <SampleRate bit-rate selection algorithm> null: <null device, zero device> random: <entropy source, Software, Yarrow> nfslock: pseudo-device kbd: new array size 4 kbd1 at kbdmux0 mem: <memory> io: <I/O> ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) rr232x: RocketRAID 232x controller driver v1.02 (Nov 14 2006 06:32:52) acpi0: <PTLTD RSDT> on motherboard ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48 acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x80801148 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=058000] [hdr=00] is there (id=005e10de) acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 1 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 1 func 0 acpi0: Power Button (fixed) acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 24 func 1 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 1 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 1 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 1 func 0 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 1 func 1 acpi_bus_number: root bus has no _BBN, assuming 0 AcpiOsDerivePciId: bus 0 dev 1 func 1 ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x8008-0x800b on acpi0 pci_link0: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 16 Validation 0 255 N 0 16 After Disable 0 255 N 0 16 pci_link1: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 17 Validation 0 255 N 0 17 After Disable 0 255 N 0 17 pci_link2: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 18 Validation 0 255 N 0 18 After Disable 0 255 N 0 18 pci_link3: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 19 Validation 0 255 N 0 19 After Disable 0 255 N 0 19 pci_link4: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 19 Validation 0 255 N 0 19 After Disable 0 255 N 0 19 pci_link5: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 20 21 22 23 Validation 0 255 N 0 20 21 22 23 After Disable 0 255 N 0 20 21 22 23 pci_link6: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 20 21 22 23 Validation 0 255 N 0 20 21 22 23 After Disable 0 255 N 0 20 21 22 23 pci_link7: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 20 21 22 23 Validation 0 255 N 0 20 21 22 23 After Disable 0 255 N 0 20 21 22 23 pci_link8: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 20 21 22 23 Validation 0 255 N 0 20 21 22 23 After Disable 0 255 N 0 20 21 22 23 pci_link9: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 20 21 22 23 Validation 0 255 N 0 20 21 22 23 After Disable 0 255 N 0 20 21 22 23 pci_link10: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 20 21 22 23 Validation 0 255 N 0 20 21 22 23 After Disable 0 255 N 0 20 21 22 23 cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 cpu2: <ACPI CPU> on acpi0 cpu3: <ACPI CPU> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x10de, dev=0x005e, revid=0xa3 bus=0, slot=0, func=0 class=05-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x10de, dev=0x0051, revid=0xa3 bus=0, slot=1, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x000f, statreg=0x00a0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) map[10]: type 4, range 32, base 0x8c00, size 10, enabled found-> vendor=0x10de, dev=0x0052, revid=0xa2 bus=0, slot=1, func=1 class=0c-05-00, hdrtype=0x00, mfdev=1 cmdreg=0x0001, statreg=0x00b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 map[10]: type 4, range 32, base 0, size 5, enabled map[20]: type 4, range 32, base 0x5000, size 6, enabled map[24]: type 4, range 32, base 0x5040, size 6, enabled found-> vendor=0x10de, dev=0x005a, revid=0xa2 bus=0, slot=2, func=0 class=0c-03-10, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base 0xc8000000, size 12, enabled pcib0: matched entry for 0.2.INTA (src \_SB_.PCI0.LUS0:0) pci_link6: Picked IRQ 20 with weight 0 ioapic0: Changing polarity for pin 20 to high pcib0: slot 2 INTA routed to irq 20 via \_SB_.PCI0.LUS0 found-> vendor=0x10de, dev=0x005b, revid=0xa3 bus=0, slot=2, func=1 class=0c-03-20, hdrtype=0x00, mfdev=1 cmdreg=0x0006, statreg=0x00b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns) intpin=b, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 1, range 32, base 0xc8001000, size 8, enabled pcib0: matched entry for 0.2.INTB (src \_SB_.PCI0.LUS2:0) pci_link7: Picked IRQ 21 with weight 0 ioapic0: Changing polarity for pin 21 to high pcib0: slot 2 INTB routed to irq 21 via \_SB_.PCI0.LUS2 found-> vendor=0x10de, dev=0x0053, revid=0xa2 bus=0, slot=6, func=0 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x00b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns) powerspec 2 supports D0 D3 current D0 map[20]: type 4, range 32, base 0x1400, size 4, enabled found-> vendor=0x10de, dev=0x0055, revid=0xa3 bus=0, slot=8, func=0 class=01-01-85, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x00b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x01 (250 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 map[10]: type 4, range 32, base 0x1430, size 3, enabled map[14]: type 4, range 32, base 0x1424, size 2, enabled map[18]: type 4, range 32, base 0x1428, size 3, enabled map[1c]: type 4, range 32, base 0x1420, size 2, enabled map[20]: type 4, range 32, base 0x1410, size 4, enabled map[24]: type 1, range 32, base 0xc8002000, size 12, enabled pcib0: matched entry for 0.8.INTA (src \_SB_.PCI0.LSI1:0) pci_link9: Picked IRQ 22 with weight 0 ioapic0: Changing polarity for pin 22 to high pcib0: slot 8 INTA routed to irq 22 via \_SB_.PCI0.LSI1 found-> vendor=0x10de, dev=0x005c, revid=0xa2 bus=0, slot=9, func=0 class=06-04-01, hdrtype=0x01, mfdev=0 cmdreg=0x0107, statreg=0x00a0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x0c (3000 ns), maxlat=0x02 (500 ns) found-> vendor=0x10de, dev=0x005d, revid=0xa3 bus=0, slot=12, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) found-> vendor=0x10de, dev=0x005d, revid=0xa3 bus=0, slot=13, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) found-> vendor=0x10de, dev=0x005d, revid=0xa3 bus=0, slot=14, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1100, revid=0x00 bus=0, slot=24, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1101, revid=0x00 bus=0, slot=24, func=1 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1102, revid=0x00 bus=0, slot=24, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1103, revid=0x00 bus=0, slot=24, func=3 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1100, revid=0x00 bus=0, slot=25, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1101, revid=0x00 bus=0, slot=25, func=1 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1102, revid=0x00 bus=0, slot=25, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x1103, revid=0x00 bus=0, slot=25, func=3 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) pci0: <memory> at device 0.0 (no driver attached) isab0: <PCI-ISA bridge> at device 1.0 on pci0 isa0: <ISA bus> on isab0 pci0: <serial bus, SMBus> at device 1.1 (no driver attached) ohci0: <OHCI (generic) USB controller> mem 0xc8000000-0xc8000fff irq 20 at device 2.0 on pci0 ohci0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xc8000000 ioapic0: routing intpin 20 (PCI IRQ 20) to vector 49 ohci0: [GIANT-LOCKED] usb0: OHCI version 1.0, legacy support usb0: SMM does not respond, resetting usb0: <OHCI (generic) USB controller> on ohci0 usb0: USB revision 1.0 uhub0: <nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 4 ports with 4 removable, self powered ehci0: <NVIDIA nForce4 USB 2.0 controller> mem 0xc8001000-0xc80010ff irq 21 at device 2.1 on pci0 ehci0: Reserved 0x100 bytes for rid 0x10 type 3 at 0xc8001000 ioapic0: routing intpin 21 (PCI IRQ 21) to vector 50 ehci0: [GIANT-LOCKED] usb1: EHCI version 1.0 usb1: companion controller, 4 ports each: usb0 usb1: <NVIDIA nForce4 USB 2.0 controller> on ehci0 usb1: USB revision 2.0 uhub1: <nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb1 device_attach: uhub1 attach returned 6 usb1: port 0, set config at addr 1 failed usb1: root hub problem, error=4 atapci0: <nVidia nForce CK804 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1400-0x140f at device 6.0 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1400 ata0: <ATA channel 0> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=60 ostat1=70 ata0: stat0=0x20 err=0x20 lsb=0x20 msb=0x20 ata0: stat1=0x30 err=0x30 lsb=0x30 msb=0x30 ata0: reset tp2 stat0=20 stat1=30 devices=0x0 ioapic0: routing intpin 14 (ISA IRQ 14) to vector 51 ata0: [MPSAFE] ata1: <ATA channel 1> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=03 ostat0=60 ostat1=70 ata1: stat0=0x20 err=0x20 lsb=0x20 msb=0x20 ata1: stat1=0x30 err=0x30 lsb=0x30 msb=0x30 ata1: reset tp2 stat0=20 stat1=30 devices=0x0 ioapic0: routing intpin 15 (ISA IRQ 15) to vector 52 ata1: [MPSAFE] atapci1: <nVidia nForce CK804 SATA300 controller> port 0x1430-0x1437,0x1424-0x1427,0x1428-0x142f,0x1420-0x1423,0x1410-0x141f mem 0xc8002000-0xc8002fff irq 22 at device 8.0 on pci0 atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1410 ioapic0: routing intpin 22 (PCI IRQ 22) to vector 53 atapci1: [MPSAFE] atapci1: Reserved 0x1000 bytes for rid 0x24 type 3 at 0xc8002000 ata2: <ATA channel 0> on atapci1 atapci1: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1430 atapci1: Reserved 0x4 bytes for rid 0x14 type 4 at 0x1424 ata2: SATA connect ready time=0ms ata2: sata_connect devices=0x1<ATA_MASTER> ata2: [MPSAFE] ata3: <ATA channel 1> on atapci1 atapci1: Reserved 0x8 bytes for rid 0x18 type 4 at 0x1428 atapci1: Reserved 0x4 bytes for rid 0x1c type 4 at 0x1420 ata3: SATA connect ready time=0ms ata3: sata_connect devices=0x1<ATA_MASTER> ata3: [MPSAFE] pcib1: <ACPI PCI-PCI bridge> at device 9.0 on pci0 pcib1: secondary bus 1 pcib1: subordinate bus 1 pcib1: I/O decode 0xf000-0xfff pcib1: memory decode 0xc9000000-0xc9ffffff pcib1: prefetched decode 0xd0000000-0xd7ffffff pcib1: Subtractively decoded bridge. pci1: <ACPI PCI bus> on pcib1 pci1: physical bus=1 found-> vendor=0x10de, dev=0x0110, revid=0xb2 bus=1, slot=5, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x01 (250 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base 0xc9000000, size 24, enabled pcib1: requested memory range 0xc9000000-0xc9ffffff: good map[14]: type 3, range 32, base 0xd0000000, size 27, enabled pcib1: requested memory range 0xd0000000-0xd7ffffff: good pcib1: matched entry for 1.5.INTA (src \_SB_.PCI0.LNK1:0) pci_link0: Picked IRQ 16 with weight 0 ioapic0: Changing polarity for pin 16 to high pcib1: slot 5 INTA routed to irq 16 via \_SB_.PCI0.LNK1 vgapci0: <VGA-compatible display> mem 0xc9000000-0xc9ffffff,0xd0000000-0xd7ffffff irq 16 at device 5.0 on pci1 pcib2: <ACPI PCI-PCI bridge> at device 12.0 on pci0 pcib2: secondary bus 2 pcib2: subordinate bus 2 pcib2: I/O decode 0xf000-0xfff pcib2: memory decode 0xca000000-0xca0fffff pcib2: no prefetched decode pci2: <ACPI PCI bus> on pcib2 pci2: physical bus=2 pci2:0:0: bad VPD cksum, remain 14 found-> vendor=0x14e4, dev=0x1659, revid=0x11 bus=2, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0146, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 VPD Ident: Broadcom NetXtreme Gigabit Ethernet Controller MSI supports 8 messages, 64 bit map[10]: type 1, range 64, base 0xca000000, size 16, enabled pcib2: requested memory range 0xca000000-0xca00ffff: good pcib2: matched entry for 2.0.INTA (src \_SB_.PCI0.LNK1:0) pcib2: slot 0 INTA routed to irq 16 via \_SB_.PCI0.LNK1 bge0: <Broadcom BCM5750 B1, ASIC rev. 0x4101> mem 0xca000000-0xca00ffff irq 16 at device 0.0 on pci2 bge0: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xca000000 miibus0: <MII bus> on bge0 brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0 brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge0: bpf attached bge0: Ethernet address: 00:17:a4:ff:79:0d ioapic0: routing intpin 16 (PCI IRQ 16) to vector 54 bge0: [MPSAFE] pcib3: <ACPI PCI-PCI bridge> at device 13.0 on pci0 pcib3: secondary bus 3 pcib3: subordinate bus 3 pcib3: I/O decode 0xf000-0xfff pcib3: memory decode 0xca100000-0xca1fffff pcib3: no prefetched decode pci3: <ACPI PCI bus> on pcib3 pci3: physical bus=3 pci3:0:0: bad VPD cksum, remain 14 found-> vendor=0x14e4, dev=0x1659, revid=0x11 bus=3, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0146, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 VPD Ident: Broadcom NetXtreme Gigabit Ethernet Controller MSI supports 8 messages, 64 bit map[10]: type 1, range 64, base 0xca100000, size 16, enabled pcib3: requested memory range 0xca100000-0xca10ffff: good pcib3: matched entry for 3.0.INTA (src \_SB_.PCI0.LNK4:0) pci_link3: Picked IRQ 19 with weight 0 ioapic0: Changing polarity for pin 19 to high pcib3: slot 0 INTA routed to irq 19 via \_SB_.PCI0.LNK4 bge1: <Broadcom BCM5750 B1, ASIC rev. 0x4101> mem 0xca100000-0xca10ffff irq 19 at device 0.0 on pci3 bge1: Reserved 0x10000 bytes for rid 0x10 type 3 at 0xca100000 miibus1: <MII bus> on bge1 brgphy1: <BCM5750 10/100/1000baseTX PHY> on miibus1 brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto bge1: bpf attached bge1: Ethernet address: 00:17:a4:ff:79:0c ioapic0: routing intpin 19 (PCI IRQ 19) to vector 55 bge1: [MPSAFE] pcib4: <ACPI PCI-PCI bridge> at device 14.0 on pci0 pcib4: secondary bus 4 pcib4: subordinate bus 4 pcib4: I/O decode 0xf000-0xfff pcib4: no prefetched decode pci4: <ACPI PCI bus> on pcib4 pci4: physical bus=4 pcib5: <ACPI Host-PCI bridge> on acpi0 pcib5: could not get PCI interrupt routing table for \_SB_.PCI1 - AE_NOT_FOUND pci128: <ACPI PCI bus> on pcib5 pci128: physical bus=128 found-> vendor=0x1022, dev=0x7458, revid=0x12 bus=128, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0157, statreg=0x0810, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x25 (9250 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7459, revid=0x12 bus=128, slot=1, func=1 class=08-00-10, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7458, revid=0x12 bus=128, slot=2, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0157, statreg=0x0810, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x25 (9250 ns), maxlat=0x00 (0 ns) found-> vendor=0x1022, dev=0x7459, revid=0x12 bus=128, slot=2, func=1 class=08-00-10, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) pcib6: <ACPI PCI-PCI bridge> at device 1.0 on pci128 pcib6: secondary bus 129 pcib6: subordinate bus 133 pcib6: I/O decode 0xf000-0xfff pcib6: prefetched decode 0xd8300000-0xd84fffff pci129: <ACPI PCI bus> on pcib6 pci129: physical bus=129 <hang>Received on Tue Nov 14 2006 - 12:53:14 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:02 UTC