Re: LSI 1030 mpt doesn't work if I build a new kernel

On Sun, Sep 24, 2006 at 04:16:01PM +0900, YONETANI Tomokazu wrote:
>
> Recently I tried installing FreeBSD 5.4-RELEASE on an IBM X335 in my
> office and tried to upgrade to 6.2-PRERELEASE, and found that although
> it doesn't hang or panic during boot, running I/O intensive applications
> (including buildworld) ends up in an I/O error, and eventually panicked and
> rebooted.
>
	This would be best on -STABLE, which the 6x thread is. Anyway,
   I have:

[root_at_tigerfish2 ~]# camcontrol devlist -v
scbus0 on sbp0 bus 0:
<  >                               at scbus0 target -1 lun -1 ()
scbus1 on mpt0 bus 0:
<SEAGATE DAT    06240-XXX 8040>    at scbus1 target 0 lun 0 (sa0,pass0)
<PLEXTOR CD-ROM PX-40TW 1.04>      at scbus1 target 4 lun 0 (pass1,cd0)
<IBM DDYS-T18350N S96H>            at scbus1 target 5 lun 0 (da0,pass2)
<  >                               at scbus1 target -1 lun -1 ()
scbus2 on mpt1 bus 0:
<SEAGATE ST336607LW 0007>          at scbus2 target 6 lun 0 (da1,pass3)
<  >                               at scbus2 target -1 lun -1 ()
scbus3 on asr0 bus 0:
<ADAPTEC RAID-5 370F>              at scbus3 target 1 lun 0 (da2,pass4)
<ADAPTEC REDIRECT DRIVE 370F>      at scbus3 target 5 lun 0 (da3,pass5)
<SUPER GEM318 0>                   at scbus3 target 6 lun 0 (ses0,pass6)
<  >                               at scbus3 target -1 lun -1 ()
scbus4 on asr0 bus 1:
<  >                               at scbus4 target -1 lun -1 ()
scbus5 on ata0 bus 0:
<SONY DVD RW DRU-800A KY01>        at scbus5 target 0 lun 0 (pass7,cd1)
<  >                               at scbus5 target -1 lun -1 ()
scbus6 on ata1 bus 0:
<  >                               at scbus6 target -1 lun -1 ()
scbus-1 on xpt0 bus 0:
<  > 

mpt0_at_pci10:6:0: class=0x010000 card=0x289510f1 chip=0x00301000 rev=0x07 hdr=0x00
    vendor   = 'LSI Logic (Was: Symbios Logic, NCR)'
    device   = 'LSI53C1020/1030 PCI-X to Ultra320 SCSI Controller'
    class    = mass storage
    subclass = SCSI
mpt1_at_pci10:6:1: class=0x010000 card=0x289510f1 chip=0x00301000 rev=0x07 hdr=0x00
    vendor   = 'LSI Logic (Was: Symbios Logic, NCR)'
    device   = 'LSI53C1020/1030 PCI-X to Ultra320 SCSI Controller'
    class    = mass storage
    subclass = SCSI

FreeBSD tigerfish2.my.domain 6.1-STABLE FreeBSD 6.1-STABLE #6: Sun Aug 27 11:03:43 CDT 2006 

   and have not had any problems with the mpt device. The controller is
   built into the Tyan S2895/Thunder K8WE board.

	I am not using the Seagate drive - it will be used to hold the
   AMD64 installation when I get around to doing that, while the IBM
   drive will continue to hold the i386 install if I need to switch 
   back. The RAID holds user data, and is not an issue when performing
   kernel builds.

	Have you tried to install the 6.1 release from CD/DVD?

							Bruce
-- 
------------------------------------------------------------------------
  "I like bad!"                         Bruce Burden    Austin, TX.
        - Thuganlitha
        The Power and the Prophet
        Robert Don Hughes