Re: Solid hang with bge interface

Lawrence Farr wrote:
> I have a Supermicro H8DAR-T based server, that was happily 
> running 6-stable from last year sometime. I swapped it out and
> have been trying to get -CURRENT installed on it but it hangs
> solid as soon as you configure the bge0 interface. The bge1
> interface will work occasionally tho. To try and rule out a 
> hardware fault I booted an AMD64-6.0RC1 cd that I had, which 
> had no problems at all with the interface: 
> 
> http://www.epcdirect.com/bootlog/6boot.txt
> 
> But the current snapshot from June, and from todays source
> hangs solid as soon as you try to set up the bge0 interface.
> 
> http://www.epcdirect.com/bootlog/currentboot.txt
> 
> As you can see, it hangs solid at "Setting hostname".
> 
> I've also removed the 3ware card "just in case" but it made
> no difference. Latest BIOS too. I found some references to
> a similar problem with bge recently too:
> 
> http://lists.freebsd.org/pipermail/freebsd-current/2007-August/075998.html
> 
> 
> Anyone else seeing this?
> 

Same here with a Supermicro H8SSL-I2 (Serverworks HT1000 based).

bge0 locks the system hard when going up, bge1 OK (but goes down a few 
hours after start). Also, an ifconfig indicates:

bge0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
         options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
         ether 00:30:48:5e:6e:56
         media: Ethernet autoselect (none <hw-loopback>)
                                     ^^^^^^^^^^^^^^^^^^
         status: no carrier
bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
         options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM>
         ether 00:30:48:5e:6e:57
         inet 192.168.1.49 netmask 0xffffff00 broadcast 192.168.1.255
         media: Ethernet autoselect (1000baseTX <full-duplex>)
         status: active

An the dmesg shows: (see "^^^^..")

	.
	.
bge0: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 
0x2100> mem 0xff4f0000-0xff4fffff irq 24 at device 3.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseTX PHY> PHY 1 on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
bge0: Ethernet address: 00:30:48:5e:6e:56
bge0: [ITHREAD]
pci2:3:1: bad VPD cksum, remain 14
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
bge1: <Broadcom NetXtreme Gigabit Ethernet Controller, ASIC rev. 0x2100> 
mem 0xff4e0000-0xff4effff irq 25 at device 3.1 on pci2
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseTX PHY> PHY 1 on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
bge1: Ethernet address: 00:30:48:5e:6e:57
bge1: [ITHREAD]
	.
	.

(I also have strange problems with the SATA controller and recent 
kernels (that works fine on other machines) that seems to read random 
sectors (at least not those requested) causing core-dumps, compiler 
internal errors, trashed sources and false positives about corrupted 
filesystems.I don't know what is going on on this platform but it 
smells^Gdoesn't looks very sane.)

RN.
IeM