On Mon, 2007-08-13 at 14:15 +0000, Wildes Miranda de Oliveira wrote: > can anyone help me ? Looking at the output, you may be better off asking on the freebsd-acpi mailing list. Gavin > thanks. > > On Mon, 6 Aug 2007 22:03:46 +0000, Wildes Miranda de Oliveira <wildes_at_itecgyn.com.br> wrote: > >> hi list, > >> > >> excuse-me my poorly english. > >> > >> recently i bought one notebook acer aspire 3680, and i have had problems > >> for load network interfaces on them. > >> the problem is that the interface ethernet Marvell Yukon don't load with > >> acpi enabled, and the interface > >> wireless Atheros AR5005 don't load with acpi disabled, with this itīs > >> never load on same bootstrap. > >> i'm annexing informations about dmesg with acpi enabled/disabled , > >> acpidump and pciconf -lv. > >> > >> i wish ask you about tunning of acpi described in man page. could this > >> solve my problem ? > >> > >> LOADER TUNABLES > >> Tunables can be set at the loader(8) prompt before booting the > > kernel > >> or > >> stored in /boot/loader.conf. Many of these tunables also have a > >> matching > >> > >> hw.acpi.serialize_methods > >> > >> Allow override of whether methods execute in parallel or > > not. > >> Enable this for serial behavior, which fixes > >> "AE_ALREADY_EXISTS" > >> errors for AML that really cannot handle parallel method > >> execu- > >> tion. It is off by default since this breaks recursive > >> methods > >> and some IBMs use such code. > >> > >> hw.pci.link.%s.%d.irq > >> > >> Override the interrupt to use for this link and index. > > This > >> capability should be used carefully, and only if a device > > is > >> not > >> working with acpi enabled. "%s" is the name of the link > >> (e.g., > >> LNKA). "%d" is the resource index when the link supports > >> multi- > >> ple IRQs. Most PCI links only have one IRQ resource, so > > the > >> below form should be used. > >> > >> hw.pci.link.%s.irq > >> > >> Override the interrupt to use. This capability should be > >> used > >> carefully, and only if a device is not working with acpi > >> enabled. > >> "%s" is the name of the link (e.g., LNKA). > >> > >> #================= ACPI DISABLED > > ==================================== > >> > >> Copyright (c) 1992-2007 The FreeBSD Project. > >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > >> The Regents of the University of California. All rights reserved. > >> FreeBSD is a registered trademark of The FreeBSD Foundation. > >> FreeBSD 7.0-CURRENT-200706 #0: Sun Jun 3 18:41:02 UTC 2007 > >> root_at_almeida.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC > >> WARNING: WITNESS option enabled, expect reduced performance. > >> MPTable: <INTEL Napa ERB > > >> Timecounter "i8254" frequency 1193182 Hz quality 0 > >> CPU: Intel(R) Celeron(R) M CPU 430 _at_ 1.73GHz (1733.41-MHz > >> 686-class CPU) > >> Origin = "GenuineIntel" Id = 0x6e8 Stepping = 8 > >> > >> > > Features=0xafe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE> > >> Features2=0xc109<SSE3,MON,TM2,xTPR,PDCM> > >> AMD Features=0x100000<NX> > >> real memory = 526974976 (502 MB) > >> avail memory = 501780480 (478 MB) > >> ioapic0: Assuming intbase of 0 > >> ioapic0 <Version 2.0> irqs 0-23 on motherboard > >> kbd1 at kbdmux0 > >> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, > > RF5413) > >> cpu0 on motherboard > >> pcib0: <MPTable Host-PCI bridge> pcibus 0 on motherboard > >> pci0: <PCI bus> on pcib0 > >> vgapci0: <VGA-compatible display> port 0x1800-0x1807 mem > >> 0xd0200000-0xd027ffff,0xc0000000-0xcfffffff,0xd0300000-0xd033ffff irq 16 > > at > >> device 2.0 on pci0 > >> agp0: <Intel 82945GM (945GM GMCH) SVGA controller> on vgapci0 > >> agp0: detected 7932k stolen memory > >> agp0: aperture size is 256M > >> vgapci1: <VGA-compatible display> mem 0xd0280000-0xd02fffff at device > > 2.1 > >> on pci0 > >> pci0: <multimedia> at device 27.0 (no driver attached) > >> pcib1: <MPTable PCI-PCI bridge> irq 16 at device 28.0 on pci0 > >> pci2: <PCI bus> on pcib1 > >> mskc0: <Marvell Yukon 88E8038 Gigabit Ethernet> port 0x2000-0x20ff mem > >> 0xd0100000-0xd0103fff irq 16 at device 0.0 on pci2 > >> msk0: <Marvell Technology Group Ltd. Yukon FE Id 0xb7 Rev 0x01> on mskc0 > >> msk0: Ethernet address: 00:16:36:d1:56:ce > >> miibus0: <MII bus> on msk0 > >> e1000phy0: <Marvell 88E3082 10/100 Fast Ethernet PHY> PHY 0 on miibus0 > >> e1000phy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > >> ukphy0: <Generic IEEE 802.3u media interface> PHY 3 on miibus0 > >> ukphy0: no media present > >> ukphy1: <Generic IEEE 802.3u media interface> PHY 6 on miibus0 > >> ukphy1: no media present > >> mskc0: [FILTER] > >> pcib2: <PCI-PCI bridge> irq 17 at device 28.1 on pci0 > >> pci3: <PCI bus> on pcib2 > >> pcib3: <PCI-PCI bridge> irq 18 at device 28.2 on pci0 > >> pci4: <PCI bus> on pcib3 > >> pcib4: <PCI-PCI bridge> irq 19 at device 28.3 on pci0 > >> pci5: <PCI bus> on pcib4 > >> uhci0: <UHCI (generic) USB controller> port 0x1820-0x183f irq 23 at > > device > >> 29.0 on pci0 > >> uhci0: [GIANT-LOCKED] > >> uhci0: [ITHREAD] > >> usb0: <UHCI (generic) USB controller> on uhci0 > >> usb0: USB revision 1.0 > >> uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 > >> uhub0: 2 ports with 2 removable, self powered > >> uhci1: <UHCI (generic) USB controller> port 0x1840-0x185f irq 19 at > > device > >> 29.1 on pci0 > >> uhci1: [GIANT-LOCKED] > >> uhci1: [ITHREAD] > >> usb1: <UHCI (generic) USB controller> on uhci1 > >> usb1: USB revision 1.0 > >> uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 > >> uhub1: 2 ports with 2 removable, self powered > >> uhci2: <UHCI (generic) USB controller> port 0x1860-0x187f irq 18 at > > device > >> 29.2 on pci0 > >> uhci2: [GIANT-LOCKED] > >> uhci2: [ITHREAD] > >> usb2: <UHCI (generic) USB controller> on uhci2 > >> usb2: USB revision 1.0 > >> uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2 > >> uhub2: 2 ports with 2 removable, self powered > >> uhci3: <UHCI (generic) USB controller> port 0x1880-0x189f irq 16 at > > device > >> 29.3 on pci0 > >> uhci3: [GIANT-LOCKED] > >> uhci3: [ITHREAD] > >> usb3: <UHCI (generic) USB controller> on uhci3 > >> usb3: USB revision 1.0 > >> uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3 > >> uhub3: 2 ports with 2 removable, self powered > >> ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem > >> 0xd0544000-0xd05443ff irq 23 at device 29.7 on pci0 > >> ehci0: [GIANT-LOCKED] > >> ehci0: [ITHREAD] > >> usb4: EHCI version 1.0 > >> usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 > >> usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0 > >> usb4: USB revision 2.0 > >> uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4 > >> uhub4: 8 ports with 8 removable, self powered > >> pcib5: <MPTable PCI-PCI bridge> at device 30.0 on pci0 > >> pci10: <PCI bus> on pcib5 > >> ath0: <Atheros 5212> mem 0xd0000000-0xd000ffff at device 3.0 on pci10 > >> pcib5: unable to route slot 3 INTA > >> ath0: could not map interrupt > >> device_attach: ath0 attach returned 6 > >> cbb0: <PCI-CardBus Bridge> mem 0xd0014000-0xd0014fff irq 20 at device > > 9.0 > >> on pci10 > >> cardbus0: <CardBus bus> on cbb0 > >> pccard0: <16-bit PCCard bus> on cbb0 > >> cbb0: [ITHREAD] > >> pci10: <mass storage> at device 9.2 (no driver attached) > >> isab0: <PCI-ISA bridge> at device 31.0 on pci0 > >> isa0: <ISA bus> on isab0 > >> atapci0: <Intel ICH7M SATA300 controller> port > >> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x18b0-0x18bf at device 31.2 on pci0 > >> ata0: <ATA channel 0> on atapci0 > >> ata0: [ITHREAD] > >> ata1: <ATA channel 1> on atapci0 > >> ata1: [ITHREAD] > >> pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > >> pmtimer0 on isa0 > >> orm0: <ISA Option ROMs> at iomem 0xcf000-0xcffff,0xdf800-0xdffff pnpid > >> ORM0000 on isa0 > >> atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0 > >> atkbd0: <AT Keyboard> irq 1 on atkbdc0 > >> kbd0 at atkbd0 > >> atkbd0: [GIANT-LOCKED] > >> atkbd0: [ITHREAD] > >> psm0: <PS/2 Mouse> irq 12 on atkbdc0 > >> psm0: [GIANT-LOCKED] > >> psm0: [ITHREAD] > >> psm0: model Generic PS/2 mouse, device ID 0 > >> ppc0: parallel port not found. > >> sc0: <System console> at flags 0x100 on isa0 > >> sc0: VGA <16 virtual consoles, flags=0x300> > >> sio0: configured irq 4 not in bitmap of probed irqs 0 > >> sio0: port may not be enabled > >> sio0: configured irq 4 not in bitmap of probed irqs 0 > >> sio0: port may not be enabled > >> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > >> sio0: type 8250 or not responding > >> sio0: [FILTER] > >> sio1: configured irq 3 not in bitmap of probed irqs 0 > >> sio1: port may not be enabled > >> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on > > isa0 > >> unknown: <PNP0c01> can't assign resources (memory) > >> unknown: <PNP0303> can't assign resources (port) > >> unknown: <PNP0c02> can't assign resources (memory) > >> unknown: <PNP0c02> can't assign resources (memory) > >> unknown: <PNP0c02> can't assign resources (memory) > >> unknown: <PNP0c02> can't assign resources (memory) > >> unknown: <INT0800> can't assign resources (memory) > >> unknown: <PNP0f13> can't assign resources (irq) > >> Timecounter "TSC" frequency 1733412980 Hz quality 800 > >> Timecounters tick every 1.000 msec > >> ad0: 76319MB <TOSHIBA MK8034GSX AH301J> at ata0-master SATA150 > >> acd0: CDRW <TSSTcorpCDW/DVD TS-L462D/AC01> at ata1-master UDMA33 > >> GEOM_LABEL: Label for provider ad0s3 is msdosfs/DADOS. > >> Trying to mount root from ufs:/dev/ad0s1a > >> msk0: link state changed to UP > >> > >> #====================== ACPI ENABLED > > ==================================== > >> > >> Copyright (c) 1992-2007 The FreeBSD Project. > >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > >> The Regents of the University of California. All rights reserved. > >> FreeBSD is a registered trademark of The FreeBSD Foundation. > >> FreeBSD 7.0-CURRENT-200706 #0: Sun Jun 3 18:41:02 UTC 2007 > >> root_at_almeida.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC > >> WARNING: WITNESS option enabled, expect reduced performance. > >> ACPI APIC Table: <INTEL CALISTGA> > >> Timecounter "i8254" frequency 1193182 Hz quality 0 > >> CPU: Intel(R) Celeron(R) M CPU 430 _at_ 1.73GHz (1733.41-MHz > >> 686-class CPU) > >> Origin = "GenuineIntel" Id = 0x6e8 Stepping = 8 > >> > >> > > Features=0xafe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,PBE> > >> Features2=0xc109<SSE3,MON,TM2,xTPR,PDCM> > >> AMD Features=0x100000<NX> > >> real memory = 526974976 (502 MB) > >> avail memory = 501760000 (478 MB) > >> ioapic0 <Version 2.0> irqs 0-23 on motherboard > >> kbd1 at kbdmux0 > >> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, > > RF5413) > >> acpi0: <ACRSYS ACRPRDCT> on motherboard > >> acpi0: [ITHREAD] > >> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on > >> acpi0 > >> Timecounter "HPET" frequency 14318180 Hz quality 2000 > >> acpi0: Power Button (fixed) > >> unknown: I/O range not supported > >> acpi0: reservation of fed00000, 400 (3) failed > >> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 > >> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 > >> acpi_ec0: <Embedded Controller: GPE 0x17> port 0x62,0x66 on acpi0 > >> cpu0: <ACPI CPU> on acpi0 > >> acpi_throttle0: <ACPI CPU Throttling> on cpu0 > >> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 > >> pci0: <ACPI PCI bus> on pcib0 > >> vgapci0: <VGA-compatible display> port 0x1800-0x1807 mem > >> 0xd0200000-0xd027ffff,0xc0000000-0xcfffffff,0xd0300000-0xd033ffff irq 16 > > at > >> device 2.0 on pci0 > >> agp0: <Intel 82945GM (945GM GMCH) SVGA controller> on vgapci0 > >> agp0: detected 7932k stolen memory > >> agp0: aperture size is 256M > >> vgapci1: <VGA-compatible display> mem 0xd0280000-0xd02fffff at device > > 2.1 > >> on pci0 > >> pci0: <multimedia> at device 27.0 (no driver attached) > >> pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0 > >> pci2: <ACPI PCI bus> on pcib1 > >> mskc0: <Marvell Yukon 88E8038 Gigabit Ethernet> irq 16 at device 0.0 on > >> pci2 > >> mskc0: 0x4000 bytes of rid 0x10 res 3 failed (0, 0xffffffff). > >> mskc0: unknown device: id=0x00, rev=0x00 > >> device_attach: mskc0 attach returned 6 > >> pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0 > >> pci3: <ACPI PCI bus> on pcib2 > >> pcib3: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0 > >> pci4: <ACPI PCI bus> on pcib3 > >> uhci0: <UHCI (generic) USB controller> port 0x1820-0x183f irq 23 at > > device > >> 29.0 on pci0 > >> uhci0: [GIANT-LOCKED] > >> uhci0: [ITHREAD] > >> usb0: <UHCI (generic) USB controller> on uhci0 > >> usb0: USB revision 1.0 > >> uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 > >> uhub0: 2 ports with 2 removable, self powered > >> uhci1: <UHCI (generic) USB controller> port 0x1840-0x185f irq 19 at > > device > >> 29.1 on pci0 > >> uhci1: [GIANT-LOCKED] > >> uhci1: [ITHREAD] > >> usb1: <UHCI (generic) USB controller> on uhci1 > >> usb1: USB revision 1.0 > >> uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 > >> uhub1: 2 ports with 2 removable, self powered > >> uhci2: <UHCI (generic) USB controller> port 0x1860-0x187f irq 18 at > > device > >> 29.2 on pci0 > >> uhci2: [GIANT-LOCKED] > >> uhci2: [ITHREAD] > >> usb2: <UHCI (generic) USB controller> on uhci2 > >> usb2: USB revision 1.0 > >> uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2 > >> uhub2: 2 ports with 2 removable, self powered > >> uhci3: <UHCI (generic) USB controller> port 0x1880-0x189f irq 16 at > > device > >> 29.3 on pci0 > >> uhci3: [GIANT-LOCKED] > >> uhci3: [ITHREAD] > >> usb3: <UHCI (generic) USB controller> on uhci3 > >> usb3: USB revision 1.0 > >> uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3 > >> uhub3: 2 ports with 2 removable, self powered > >> ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem > >> 0xd0544000-0xd05443ff irq 23 at device 29.7 on pci0 > >> ehci0: [GIANT-LOCKED] > >> ehci0: [ITHREAD] > >> usb4: EHCI version 1.0 > >> usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 > >> usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0 > >> usb4: USB revision 2.0 > >> uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4 > >> uhub4: 8 ports with 8 removable, self powered > >> pcib4: <ACPI PCI-PCI bridge> at device 30.0 on pci0 > >> pci10: <ACPI PCI bus> on pcib4 > >> ath0: <Atheros 5212> mem 0xd0000000-0xd000ffff at device 3.0 on pci10 > >> ath0: [ITHREAD] > >> ath0: using obsoleted if_watchdog interface > >> ath0: Ethernet address: 00:19:7d:47:ed:84 > >> ath0: mac 7.8 phy 4.5 radio 5.6 > >> cbb0: <PCI-CardBus Bridge> mem 0xd0014000-0xd0014fff irq 20 at device > > 9.0 > >> on pci10 > >> cardbus0: <CardBus bus> on cbb0 > >> pccard0: <16-bit PCCard bus> on cbb0 > >> cbb0: [ITHREAD] > >> pci10: <mass storage> at device 9.2 (no driver attached) > >> isab0: <PCI-ISA bridge> at device 31.0 on pci0 > >> isa0: <ISA bus> on isab0 > >> atapci0: <Intel ICH7M SATA300 controller> port > >> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x18b0-0x18bf at device 31.2 on pci0 > >> ata0: <ATA channel 0> on atapci0 > >> ata0: [ITHREAD] > >> ata1: <ATA channel 1> on atapci0 > >> ata1: [ITHREAD] > >> pci0: <serial bus, SMBus> at device 31.3 (no driver attached) > >> acpi_acad0: <AC Adapter> on acpi0 > >> battery0: <ACPI Control Method Battery> on acpi0 > >> acpi_lid0: <Control Method Lid Switch> on acpi0 > >> acpi_button0: <Power Button> on acpi0 > >> acpi_button1: <Sleep Button> on acpi0 > >> acpi_tz0: <Thermal Zone> on acpi0 > >> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 > >> atkbd0: <AT Keyboard> irq 1 on atkbdc0 > >> kbd0 at atkbd0 > >> atkbd0: [GIANT-LOCKED] > >> atkbd0: [ITHREAD] > >> psm0: <PS/2 Mouse> irq 12 on atkbdc0 > >> psm0: [GIANT-LOCKED] > >> psm0: [ITHREAD] > >> psm0: model Generic PS/2 mouse, device ID 0 > >> pmtimer0 on isa0 > >> orm0: <ISA Option ROMs> at iomem 0xcf000-0xcffff,0xdf800-0xdffff pnpid > >> ORM0000 on isa0 > >> ppc0: parallel port not found. > >> sc0: <System console> at flags 0x100 on isa0 > >> sc0: VGA <16 virtual consoles, flags=0x300> > >> sio0: configured irq 4 not in bitmap of probed irqs 0 > >> sio0: port may not be enabled > >> sio0: configured irq 4 not in bitmap of probed irqs 0 > >> sio0: port may not be enabled > >> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > >> sio0: type 8250 or not responding > >> sio0: [FILTER] > >> sio1: configured irq 3 not in bitmap of probed irqs 0 > >> sio1: port may not be enabled > >> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on > > isa0 > >> Timecounter "TSC" frequency 1733409431 Hz quality 800 > >> Timecounters tick every 1.000 msec > >> ad0: 76319MB <TOSHIBA MK8034GSX AH301J> at ata0-master SATA150 > >> acd0: CDRW <TSSTcorpCDW/DVD TS-L462D/AC01> at ata1-master UDMA33 > >> GEOM_LABEL: Label for provider ad0s3 is msdosfs/DADOS. > >> Trying to mount root from ufs:/dev/ad0s1a > >> > >> #======================== PCICONF -LV > > ==================================== > >> > >> hostb0_at_pci0:0:0: class=0x060000 card=0x01101025 chip=0x27a08086 rev=0x03 > >> hdr=0x00 > >> vendor = 'Intel Corporation' > >> device = '955XM/945GM/PM/GMS/940GML Express Processor to DRAM > >> Controller' > >> class = bridge > >> subclass = HOST-PCI > >> vgapci0_at_pci0:2:0: class=0x030000 card=0x01101025 chip=0x27a28086 > > rev=0x03 > >> hdr=0x00 > >> vendor = 'Intel Corporation' > >> device = 'Mobile Integrated Graphics Controller' > >> class = display > >> subclass = VGA > >> vgapci1_at_pci0:2:1: class=0x038000 card=0x01101025 chip=0x27a68086 > > rev=0x03 > >> hdr=0x00 > >> vendor = 'Intel Corporation' > >> device = 'Mobile Integrated Graphics Controller' > >> class = display > >> none0_at_pci0:27:0: class=0x040300 card=0x01101025 chip=0x27d88086 rev=0x02 > >> hdr=0x00 > >> vendor = 'Intel Corporation' > >> device = '82801G (ICH7 Family) High Definition Audio' > >> class = multimedia > >> pcib1_at_pci0:28:0: class=0x060400 card=0x01101025 chip=0x27d08086 rev=0x02 > >> hdr=0x01 > >> vendor = 'Intel Corporation' > >> device = '82801G (ICH7 Family) PCI Express Root Port' > >> class = bridge > >> subclass = PCI-PCI > >> pcib2_at_pci0:28:1: class=0x060400 card=0x01101025 chip=0x27d28086 rev=0x02 > >> hdr=0x01 > >> vendor = 'Intel Corporation' > >> device = '82801G (ICH7 Family) PCI Express Root Port' > >> class = bridge > >> subclass = PCI-PCI > >> pcib3_at_pci0:28:2: class=0x060400 card=0x01101025 chip=0x27d48086 rev=0x02 > >> hdr=0x01 > >> vendor = 'Intel Corporation' > >> device = '82801G (ICH7 Family) PCI Express Root Port' > >> class = bridge > >> subclass = PCI-PCI > >> uhci0_at_pci0:29:0: class=0x0c0300 card=0x01101025 chip=0x27c88086 rev=0x02 > >> hdr=0x00 > >> vendor = 'Intel Corporation' > >> device = '82801G (ICH7 Family) USB Universal Host Controller' > >> class = serial bus > >> subclass = USB > >> uhci1_at_pci0:29:1: class=0x0c0300 card=0x01101025 chip=0x27c98086 rev=0x02 > >> hdr=0x00 > >> vendor = 'Intel Corporation' > >> device = '82801G (ICH7 Family) USB Universal Host Controller' > >> class = serial bus > >> subclass = USB > >> uhci2_at_pci0:29:2: class=0x0c0300 card=0x01101025 chip=0x27ca8086 rev=0x02 > >> hdr=0x00 > >> vendor = 'Intel Corporation' > >> device = '82801G (ICH7 Family) USB Universal Host Controller' > >> class = serial bus > >> subclass = USB > >> uhci3_at_pci0:29:3: class=0x0c0300 card=0x01101025 chip=0x27cb8086 rev=0x02 > >> hdr=0x00 > >> vendor = 'Intel Corporation' > >> device = '82801G (ICH7 Family) USB Universal Host Controller' > >> class = serial bus > >> subclass = USB > >> ehci0_at_pci0:29:7: class=0x0c0320 card=0x01101025 chip=0x27cc8086 rev=0x02 > >> hdr=0x00 > >> vendor = 'Intel Corporation' > >> device = '82801G (ICH7 Family) USB 2.0 Enhanced Host Controller' > >> class = serial bus > >> subclass = USB > >> pcib4_at_pci0:30:0: class=0x060401 card=0x01101025 chip=0x24488086 rev=0xe2 > >> hdr=0x01 > >> vendor = 'Intel Corporation' > >> device = '82801BAM/CAM/DBM (ICH2-M/3-M/4-M) Hub Interface to PCI > >> Bridge' > >> class = bridge > >> subclass = PCI-PCI > >> isab0_at_pci0:31:0: class=0x060100 card=0x01101025 chip=0x27b98086 rev=0x02 > >> hdr=0x00 > >> vendor = 'Intel Corporation' > >> device = '82801GBM (ICH7-M) LPC Interface Controller' > >> class = bridge > >> subclass = PCI-ISA > >> atapci0_at_pci0:31:2: class=0x010180 card=0x01101025 chip=0x27c48086 > > rev=0x02 > >> hdr=0x00 > >> vendor = 'Intel Corporation' > >> device = '82801GBM/GHM (ICH7-M Family) Serial ATA Storage > >> Controller' > >> class = mass storage > >> subclass = ATA > >> none1_at_pci0:31:3: class=0x0c0500 card=0x01101025 chip=0x27da8086 rev=0x02 > >> hdr=0x00 > >> vendor = 'Intel Corporation' > >> device = '82801G (ICH7 Family) SMBus Controller' > >> class = serial bus > >> subclass = SMBus > >> mskc0_at_pci2:0:0: class=0x020000 card=0x01101025 chip=0x435211ab rev=0x14 > >> hdr=0x00 > >> vendor = 'Marvell Semiconductor (Was: Galileo Technology Ltd)' > >> device = 'Yukon 88E8038 PCI-E Fast Ethernet Controller' > >> class = network > >> subclass = ethernet > >> ath0_at_pci10:3:0: class=0x020000 card=0x04181468 chip=0x001a168c rev=0x01 > >> hdr=0x00 > >> vendor = 'Atheros Communications Inc.' > >> device = 'Atheros AR5005G Atheros AR5005G 802.11abg NIC Chipset' > >> class = network > >> subclass = ethernet > >> cbb0_at_pci10:9:0: class=0x060700 card=0x01101025 chip=0x8039104c rev=0x00 > >> hdr=0x02 > >> vendor = 'Texas Instruments (TI)' > >> device = 'PCIxx12 Cardbus Controller' > >> class = bridge > >> subclass = PCI-CardBus > >> none2_at_pci10:9:2: class=0x018000 card=0x01101025 chip=0x803b104c rev=0x00 > >> hdr=0x00 > >> vendor = 'Texas Instruments (TI)' > >> device = 'PCIxx12 Integrated Flash Media Controller' > >> class = mass storage > > _______________________________________________ > freebsd-current_at_freebsd.org mailing list > http://lists.freebsd.org/mailman/listinfo/freebsd-current > To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"Received on Fri Aug 24 2007 - 11:42:36 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:16 UTC