******************************************************************* Click here to view our e-mail legal notice: http://www.mxit.co.za/pdfs/mxit_legal.pdf or call: +27 21 888 5000 ******************************************************************* > HARDWARE= DELL 1955 BLADE > OS Version= CURRENT i386(2007-02-01) > > When I assign an IP to one of the BCE interfaces on the system the kernel > PANICS. > > >From KDB: > --------------------------------------------------------------- > Panic: invalid ife->ifm_date (0xa) in mii_phy_setmedia > I guess ukphy(4) was used to serve the PHY. Would you post verbosed boot message? > Cpuid = 0 > KDB: enter:panic > [ thread pid 715 tid 100041] > Stopped at kdb_enter + 0x2b:nop > --------------------------------------------------------------- > > I then type "panic" and it writes a vmcore dump. > > But when I analyze the vmcore using kgdb and run a "bt" it only gives me the > backtrace of the kdb and shutdown. > > Is there a way to write a dump without kdb interfering? > > Another thing, I tried to install CURRENT-snapshot-2007-01(AMD64), but after it > boots from the USB DVDROM. Sysinstall cannot access the USB DVDROM. > Is this a known problem? Hope this is what your requested. ---------------------------------------------------------------------------- Copyright (c) 1992-2007 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.0-CURRENT #1: Tue Jan 9 16:14:37 UTC 2007 root_at_:/usr/obj/usr/src/sys/GENERIC WARNING: WITNESS option enabled, expect reduced performance. Using 64 colors for the VM-PQ tuning (4096, 16) Preloaded elf kernel "/boot/kernel/kernel" at 0xc0c17000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0c17160. Calibrating clock(s) ... i8254 clock: 1193181 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 1995012030 Hz CPU: Intel(R) Xeon(R) CPU 5130 _at_ 2.00GHz (1995.01-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6f6 Stepping = 6 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMO V,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x4e33d<SSE3,RSVD2,MON,DS_CPL,VMX,TM2,SSSE3,CX16,XTPR,<b15>,<b18>> AMD Features=0x20100000<NX,LM> AMD Features2=0x1<LAHF> Cores per package: 2 Instruction TLB: 4 KB Pages, 4-way set associative, 128 entries 1st-level instruction cache: 32 KB, 8-way set associative, 64 byte line size 1st-level data cache: 32 KB, 8-way set associative, 64 byte line size L2 cache: 4096 kbytes, 16-way associative, 64 bytes/line real memory = 3489300480 (3327 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000001028000 - 0x00000000cc4cefff, 3410653184 bytes (832679 pages) avail memory = 3410173952 (3252 MB) MP Configuration Table version 1.4 found at 0xc00f0000 Table 'FACP' at 0xf3698 Table 'APIC' at 0xf378c MADT: Found table at 0xf378c APIC: Using the MADT enumerator. MADT: Found CPU APIC ID 0 ACPI ID 1: enabled SMP: Added CPU 0 (AP) MADT: Found CPU APIC ID 1 ACPI ID 2: enabled SMP: Added CPU 1 (AP) MADT: Found CPU APIC ID 18 ACPI ID 3: disabled MADT: Found CPU APIC ID 19 ACPI ID 4: disabled MADT: Found CPU APIC ID 20 ACPI ID 5: disabled MADT: Found CPU APIC ID 21 ACPI ID 6: disabled MADT: Found CPU APIC ID 22 ACPI ID 7: disabled MADT: Found CPU APIC ID 23 ACPI ID 8: disabled INTR: Adding local APIC 0 as a target ACPI APIC Table: <DELL PE_SC3 > INTR: Adding local APIC 1 as a target FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 bios32: Found BIOS32 Service Directory header at 0xc00ffe80 bios32: Entry = 0xffe90 (c00ffe90) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xf0000+0xb43e pnpbios: Found PnP BIOS data at 0xc00fe2d0 pnpbios: Entry = f0000:e2f4 Rev = 1.0 Other BIOS signatures found: APIC: CPU 0 has ACPI ID 1 APIC: CPU 1 has ACPI ID 2 MADT: Found IO APIC ID 2, Interrupt 0 at 0xfec00000 ioapic0: Changing APIC ID to 2 ioapic0: Routing external 8259A's -> intpin 0 MADT: Found IO APIC ID 3, Interrupt 32 at 0xfec80000 ioapic1: Changing APIC ID to 3 ioapic1: WARNING: intbase 32 != expected base 24 MADT: Found IO APIC ID 4, Interrupt 192 at 0xfec85000 ioapic2: Changing APIC ID to 4 ioapic2: WARNING: intbase 192 != expected base 56 lapic0: Routing NMI -> LINT1 lapic0: LINT1 trigger: edge lapic0: LINT1 polarity: high lapic1: Routing NMI -> LINT1 lapic1: LINT1 trigger: edge lapic1: LINT1 polarity: high MADT: Ignoring local NMI routed to ACPI CPU 3 MADT: Ignoring local NMI routed to ACPI CPU 4 MADT: Ignoring local NMI routed to ACPI CPU 5 MADT: Ignoring local NMI routed to ACPI CPU 6 MADT: Ignoring local NMI routed to ACPI CPU 7 MADT: Ignoring local NMI routed to ACPI CPU 8 MADT: Interrupt override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 MADT: Interrupt override: source 9, irq 9 ioapic0: intpin 9 trigger: level ioapic0 <Version 2.0> irqs 0-23 on motherboard ioapic1 <Version 2.0> irqs 32-55 on motherboard ioapic2 <Version 2.0> irqs 192-215 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000 ath_rate: version 1.2 <SampleRate bit-rate selection algorithm> wlan: <802.11 Link Layer> null: <null device, zero device> random: <entropy source, Software, Yarrow> nfslock: pseudo-device io: <I/O> kbd: new array size 4 kbd1 at kbdmux0 mem: <memory> Pentium Pro MTRR support enabled ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) rr232x: RocketRAID 232x controller driver v1.02 (Jan 9 2007 16:14:25) npx0: INT 16 interface acpi0: <DELL PE_SC3> on motherboard ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48 acpi0: [MPSAFE] pci_open(1): mode 1 addr port (0x0cf8) is 0x800080e0 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=25d88086) pcibios: BIOS version 2.10 AcpiOsDerivePciId: bus 0 dev 31 func 0 acpi0: Power Button (fixed) acpi0: wakeup code va 0xda723000 pa 0x9d000 AcpiOsDerivePciId: bus 0 dev 16 func 1 AcpiOsDerivePciId: bus 0 dev 16 func 0 ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 pci_link0: Index IRQ Rtd Ref IRQs Initial Probe 0 11 N 0 3 4 5 6 7 10 11 12 Validation 0 11 N 0 3 4 5 6 7 10 11 12 After Disable 0 255 N 0 3 4 5 6 7 10 11 12 pci_link1: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 Validation 0 255 N 0 3 4 5 6 7 10 11 12 After Disable 0 255 N 0 3 4 5 6 7 10 11 12 pci_link2: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 Validation 0 255 N 0 3 4 5 6 7 10 11 12 After Disable 0 255 N 0 3 4 5 6 7 10 11 12 pci_link3: Index IRQ Rtd Ref IRQs Initial Probe 0 10 N 0 3 4 5 6 7 10 11 12 Validation 0 10 N 0 3 4 5 6 7 10 11 12 After Disable 0 255 N 0 3 4 5 6 7 10 11 12 pci_link4: Index IRQ Rtd Ref IRQs Initial Probe 0 14 N 0 3 4 5 6 7 10 11 12 Validation 0 255 N 0 3 4 5 6 7 10 11 12 After Disable 0 255 N 0 3 4 5 6 7 10 11 12 pci_link5: Index IRQ Rtd Ref IRQs Initial Probe 0 15 N 0 3 4 5 6 7 10 11 12 Validation 0 255 N 0 3 4 5 6 7 10 11 12 After Disable 0 255 N 0 3 4 5 6 7 10 11 12 pci_link6: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 Validation 0 255 N 0 3 4 5 6 7 10 11 12 After Disable 0 255 N 0 3 4 5 6 7 10 11 12 pci_link7: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 3 4 5 6 7 10 11 12 Validation 0 255 N 0 3 4 5 6 7 10 11 12 After Disable 0 255 N 0 3 4 5 6 7 10 11 12 cpu0: <ACPI CPU> on acpi0 cpu0: switching to generic Cx mode cpu1: <ACPI CPU> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x8086, dev=0x25d8, revid=0x92 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0144, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 MSI supports 2 messages found-> vendor=0x8086, dev=0x25e2, revid=0x92 bus=0, slot=2, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 MSI supports 2 messages found-> vendor=0x8086, dev=0x25e3, revid=0x92 bus=0, slot=3, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 MSI supports 2 messages found-> vendor=0x8086, dev=0x25e4, revid=0x92 bus=0, slot=4, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 MSI supports 2 messages found-> vendor=0x8086, dev=0x25e5, revid=0x92 bus=0, slot=5, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 MSI supports 2 messages found-> vendor=0x8086, dev=0x25e6, revid=0x92 bus=0, slot=6, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 MSI supports 2 messages found-> vendor=0x8086, dev=0x25e7, revid=0x92 bus=0, slot=7, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 MSI supports 2 messages found-> vendor=0x8086, dev=0x25f0, revid=0x92 bus=0, slot=16, func=0 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x25f0, revid=0x92 bus=0, slot=16, func=1 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x25f0, revid=0x92 bus=0, slot=16, func=2 class=06-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x25f1, revid=0x92 bus=0, slot=17, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x25f3, revid=0x92 bus=0, slot=19, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x25f5, revid=0x92 bus=0, slot=21, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x25f6, revid=0x92 bus=0, slot=22, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2690, revid=0x09 bus=0, slot=28, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 MSI supports 1 message found-> vendor=0x8086, dev=0x2688, revid=0x09 bus=0, slot=29, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=15 map[20]: type 4, range 32, base 0xcce0, size 5, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 21 found-> vendor=0x8086, dev=0x2689, revid=0x09 bus=0, slot=29, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=14 map[20]: type 4, range 32, base 0xccc0, size 5, enabled pcib0: matched entry for 0.29.INTB pcib0: slot 29 INTB hardwired to IRQ 20 found-> vendor=0x8086, dev=0x268c, revid=0x09 bus=0, slot=29, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=15 powerspec 2 supports D0 D3 current D0 map[10]: type 1, range 32, base 0xfc600000, size 10, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 21 found-> vendor=0x8086, dev=0x244e, revid=0xd9 bus=0, slot=30, func=0 class=06-04-01, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x0b (2750 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x2670, revid=0x09 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x0147, statreg=0x0200, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0 pcib1: secondary bus 3 pcib1: subordinate bus 8 pcib1: I/O decode 0xf000-0xfff pcib1: memory decode 0xf2000000-0xf7ffffff pcib1: no prefetched decode pci3: <ACPI PCI bus> on pcib1 pci3: physical bus=3 found-> vendor=0x8086, dev=0x3500, revid=0x01 bus=3, slot=0, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 found-> vendor=0x8086, dev=0x350c, revid=0x01 bus=3, slot=0, func=3 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci3 pcib2: secondary bus 4 pcib2: subordinate bus 7 pcib2: I/O decode 0xf000-0xfff pcib2: memory decode 0xf4000000-0xf7ffffff pcib2: no prefetched decode pci4: <ACPI PCI bus> on pcib2 pci4: physical bus=4 found-> vendor=0x8086, dev=0x3510, revid=0x01 bus=4, slot=0, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit found-> vendor=0x8086, dev=0x3514, revid=0x01 bus=4, slot=1, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x03 (750 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit pcib3: <ACPI PCI-PCI bridge> at device 0.0 on pci4 pcib3: secondary bus 5 pcib3: subordinate bus 6 pcib3: I/O decode 0xf000-0xfff pcib3: memory decode 0xf4000000-0xf7ffffff pcib3: no prefetched decode pci5: <ACPI PCI bus> on pcib3 pci5: physical bus=5 found-> vendor=0x1166, dev=0x0103, revid=0xc3 bus=5, slot=0, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 pcib4: <PCI-PCI bridge> at device 0.0 on pci5 pcib4: secondary bus 6 pcib4: subordinate bus 6 pcib4: I/O decode 0xf000-0xfff pcib4: memory decode 0xf4000000-0xf7ffffff pcib4: no prefetched decode pci6: <PCI bus> on pcib4 pci6: physical bus=6 pci6:0:0: bad VPD cksum, remain 228 found-> vendor=0x14e4, dev=0x16ac, revid=0x12 bus=6, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x015e, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 VPD Ident: Broadcom NetXtreme II Ethernet Controller MSI supports 1 message, 64 bit map[10]: type 1, range 64, base 0xf4000000, size 25, enabled pcib4: requested memory range 0xf4000000-0xf5ffffff: good pcib3: requested memory range 0xf4000000-0xf5ffffff: good pcib2: requested memory range 0xf4000000-0xf5ffffff: good pcib1: requested memory range 0xf4000000-0xf5ffffff: good pcib3: matched entry for 5.0.INTA pcib3: slot 0 INTA hardwired to IRQ 16 pcib4: slot 0 INTA is routed to irq 16 bce0: <Broadcom NetXtreme II BCM5708S 1000Base-T (B2), v0.9.6> mem 0xf4000000-0xf5ffffff irq 16 at device 0.0 on pci6 bce0: Reserved 0x2000000 bytes for rid 0x10 type 3 at 0xf4000000 bce0: attempting to allocate 1 MSI vectors (1 supported) bce0: using IRQ 256 for MSI bce0: ASIC ID 0x57081021; Revision (B2); PCI-X 64-bit 133MHz miibus0: <MII bus> on bce0 gentbi0: <Generic ten-bit interface> PHY 2 on miibus0 gentbi0: OUI 0x0050ef, model 0x0015, rev. 1 gentbi0: 1000baseSX, 1000baseSX-FDX, auto bce0: bpf attached bce0: Ethernet address: 00:15:c5:fc:fa:5f bce0: [MPSAFE] pcib5: <ACPI PCI-PCI bridge> at device 1.0 on pci4 pcib5: secondary bus 7 pcib5: subordinate bus 7 pcib5: I/O decode 0xf000-0xfff pcib5: no prefetched decode pci7: <ACPI PCI bus> on pcib5 pci7: physical bus=7 pcib6: <ACPI PCI-PCI bridge> at device 0.3 on pci3 pcib6: secondary bus 8 pcib6: subordinate bus 8 pcib6: I/O decode 0xf000-0xfff pcib6: no prefetched decode pci8: <ACPI PCI bus> on pcib6 pci8: physical bus=8 pcib7: <ACPI PCI-PCI bridge> at device 3.0 on pci0 pcib7: secondary bus 9 pcib7: subordinate bus 9 pcib7: I/O decode 0xf000-0xfff pcib7: no prefetched decode pci9: <ACPI PCI bus> on pcib7 pci9: physical bus=9 pcib8: <ACPI PCI-PCI bridge> at device 4.0 on pci0 pcib8: secondary bus 10 pcib8: subordinate bus 10 pcib8: I/O decode 0xf000-0xfff pcib8: no prefetched decode pci10: <ACPI PCI bus> on pcib8 pci10: physical bus=10 pcib9: <PCI-PCI bridge> at device 5.0 on pci0 pcib9: secondary bus 11 pcib9: subordinate bus 11 pcib9: I/O decode 0xf000-0xfff pcib9: no prefetched decode pci11: <PCI bus> on pcib9 pci11: physical bus=11 pcib10: <ACPI PCI-PCI bridge> at device 6.0 on pci0 pcib10: secondary bus 12 pcib10: subordinate bus 12 pcib10: I/O decode 0xf000-0xfff pcib10: no prefetched decode pci12: <ACPI PCI bus> on pcib10 pci12: physical bus=12 pcib11: <ACPI PCI-PCI bridge> at device 7.0 on pci0 pcib11: secondary bus 13 pcib11: subordinate bus 14 pcib11: I/O decode 0xe000-0xefff pcib11: memory decode 0xfc300000-0xfc5fffff pcib11: no prefetched decode pci13: <ACPI PCI bus> on pcib11 pci13: physical bus=13 found-> vendor=0x8086, dev=0x032c, revid=0x09 bus=13, slot=0, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit pcib12: <ACPI PCI-PCI bridge> at device 0.0 on pci13 pcib12: secondary bus 14 pcib12: subordinate bus 14 pcib12: I/O decode 0xe000-0xefff pcib12: memory decode 0xfc400000-0xfc5fffff pcib12: no prefetched decode pci14: <ACPI PCI bus> on pcib12 pci14: physical bus=14 found-> vendor=0x1000, dev=0x0054, revid=0x01 bus=14, slot=8, func=0 class=01-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0157, statreg=0x0230, cachelnsz=16 (dwords) lattimer=0x48 (2160 ns), mingnt=0x40 (16000 ns), maxlat=0x0a (2500 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 MSI supports 1 message, 64 bit MSI-X supports 1 message in map 0x14 map[10]: type 4, range 32, base 0xec00, size 8, enabled pcib12: requested I/O range 0xec00-0xecff: in range pcib11: requested I/O range 0xec00-0xecff: in range map[14]: type 1, range 64, base 0xfc4fc000, size 14, enabled pcib12: requested memory range 0xfc4fc000-0xfc4fffff: good pcib11: requested memory range 0xfc4fc000-0xfc4fffff: good map[1c]: type 1, range 64, base 0xfc4e0000, size 16, enabled pcib12: requested memory range 0xfc4e0000-0xfc4effff: good pcib11: requested memory range 0xfc4e0000-0xfc4effff: good pcib12: matched entry for 14.8.INTA pcib12: slot 8 INTA hardwired to IRQ 192 mpt0: <LSILogic SAS/SATA Adapter> port 0xec00-0xecff mem 0xfc4fc000-0xfc4fffff,0xfc4e0000-0xfc4effff irq 192 at device 8.0 on pci14 mpt0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xec00 mpt0: Reserved 0x4000 bytes for rid 0x14 type 3 at 0xfc4fc000 ioapic2: routing intpin 0 (PCI IRQ 192) to vector 50 mpt0: [GIANT-LOCKED] mpt0: MPI Version=1.5.12.0 mpt0: mpt_cam_event: 0x16 mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). mpt0: mpt_cam_event: 0x12 mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required). mpt0: mpt_cam_event: 0x12 mpt0: Unhandled Event Notify Frame. Event 0x12 (ACK not required). mpt0: mpt_cam_event: 0x16 mpt0: Unhandled Event Notify Frame. Event 0x16 (ACK not required). pcib13: <ACPI PCI-PCI bridge> at device 28.0 on pci0 pcib13: secondary bus 1 pcib13: subordinate bus 2 pcib13: I/O decode 0xf000-0xfff pcib13: memory decode 0xf8000000-0xfbffffff pcib13: no prefetched decode pci1: <ACPI PCI bus> on pcib13 pci1: physical bus=1 found-> vendor=0x1166, dev=0x0103, revid=0xc3 bus=1, slot=0, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 cmdreg=0x0147, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x06 (1500 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 pcib14: <PCI-PCI bridge> at device 0.0 on pci1 pcib14: secondary bus 2 pcib14: subordinate bus 2 pcib14: I/O decode 0xf000-0xfff pcib14: memory decode 0xf8000000-0xfbffffff pcib14: no prefetched decode pci2: <PCI bus> on pcib14 pci2: physical bus=2 pci2:0:0: bad VPD cksum, remain 228 found-> vendor=0x14e4, dev=0x16ac, revid=0x12 bus=2, slot=0, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x015e, statreg=0x02b0, cachelnsz=16 (dwords) lattimer=0x20 (960 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 VPD Ident: Broadcom NetXtreme II Ethernet Controller MSI supports 1 message, 64 bit map[10]: type 1, range 64, base 0xf8000000, size 25, enabled pcib14: requested memory range 0xf8000000-0xf9ffffff: good pcib13: requested memory range 0xf8000000-0xf9ffffff: good pcib13: matched entry for 1.0.INTA pcib13: slot 0 INTA hardwired to IRQ 16 pcib14: slot 0 INTA is routed to irq 16 bce1: <Broadcom NetXtreme II BCM5708S 1000Base-T (B2), v0.9.6> mem 0xf8000000-0xf9ffffff irq 16 at device 0.0 on pci2 bce1: Reserved 0x2000000 bytes for rid 0x10 type 3 at 0xf8000000 bce1: attempting to allocate 1 MSI vectors (1 supported) bce1: using IRQ 257 for MSI bce1: ASIC ID 0x57081021; Revision (B2); PCI-X 64-bit 133MHz miibus1: <MII bus> on bce1 gentbi1: <Generic ten-bit interface> PHY 2 on miibus1 gentbi1: OUI 0x0050ef, model 0x0015, rev. 1 gentbi1: 1000baseSX, 1000baseSX-FDX, auto bce1: bpf attached bce1: Ethernet address: 00:15:c5:fc:fa:5d bce1: [MPSAFE] uhci0: <UHCI (generic) USB controller> port 0xcce0-0xccff irq 21 at device 29.0 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xcce0 ioapic0: routing intpin 21 (PCI IRQ 21) to vector 52 uhci0: [GIANT-LOCKED] usb0: <UHCI (generic) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 2 ports with 2 removable, self powered uhci1: <UHCI (generic) USB controller> port 0xccc0-0xccdf irq 20 at device 29.1 on pci0 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0xccc0 ioapic0: routing intpin 20 (PCI IRQ 20) to vector 53 uhci1: [GIANT-LOCKED] usb1: <UHCI (generic) USB controller> on uhci1 usb1: USB revision 1.0 uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 uhub1: 2 ports with 2 removable, self powered ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfc600000-0xfc6003ff irq 21 at device 29.7 on pci0 ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xfc600000 ehci0: [GIANT-LOCKED] usb2: EHCI version 1.0 usb2: companion controllers, 2 ports each: usb0 usb1 usb2: <EHCI (generic) USB 2.0 controller> on ehci0 usb2: USB revision 2.0 uhub2: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2 uhub2: 4 ports with 4 removable, self powered umass0: <Seagate ST94811U2-RK, class 0/0, rev 2.00/2.00, addr 2> on uhub2 umass0:1:0:-1: Attached to scbus1 pcib15: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib15: secondary bus 15 pcib15: subordinate bus 15 pcib15: I/O decode 0xd000-0xdfff pcib15: memory decode 0xfc100000-0xfc2fffff pcib15: prefetched decode 0xd8000000-0xdfffffff pcib15: Subtractively decoded bridge. pci15: <ACPI PCI bus> on pcib15 pci15: physical bus=15 found-> vendor=0x1002, dev=0x515e, revid=0x02 bus=15, slot=13, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x01a7, statreg=0x0290, cachelnsz=16 (dwords) lattimer=0x20 (960 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type 3, range 32, base 0xd8000000, size 27, enabled pcib15: requested memory range 0xd8000000-0xdfffffff: good map[14]: type 4, range 32, base 0xdc00, size 8, enabled pcib15: requested I/O range 0xdc00-0xdcff: in range map[18]: type 1, range 32, base 0xfc1f0000, size 16, enabled pcib15: requested memory range 0xfc1f0000-0xfc1fffff: good pcib15: matched entry for 15.13.INTA pcib15: slot 13 INTA hardwired to IRQ 19 vgapci0: <VGA-compatible display> port 0xdc00-0xdcff mem 0xd8000000-0xdfffffff,0xfc1f0000-0xfc1fffff irq 19 at device 13.0 on pci15 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 acpi_hpet0: vend: 0x8086 rev: 0x1 num: 1 hz: 14318180 opts: leg_route count_size Timecounter "HPET" frequency 14318180 Hz quality 2000 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0065 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 ioapic0: routing intpin 1 (ISA IRQ 1) to vector 54 atkbd0: [GIANT-LOCKED] psm0: unable to allocate IRQ psmcpnp0: <PS/2 mouse port> irq 12 on acpi0 psm0: current command byte:0065 psm0: <PS/2 Mouse> irq 12 on atkbdc0 ioapic0: routing intpin 12 (ISA IRQ 12) to vector 55 psm0: [GIANT-LOCKED] psm0: model IntelliMouse Explorer, device ID 4-00, 5 buttons psm0: config:00000000, flags:00000008, packet size:4 psm0: syncmask:08, syncbits:00 unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff ex_isa_identify() atkbdc: atkbdc0 already exists; skipping it pnp_identify: Trying Read_Port at 203 pnp_identify: Trying Read_Port at 243 pnp_identify: Trying Read_Port at 283 pnp_identify: Trying Read_Port at 2c3 pnp_identify: Trying Read_Port at 303 pnp_identify: Trying Read_Port at 343 pnp_identify: Trying Read_Port at 383 pnp_identify: Trying Read_Port at 3c3 PNP Identify complete ahc_isa_probe 0: ioport 0xc00 alloc failed ahc_isa_probe 12: ioport 0xcc00 alloc failed ahc_isa_probe 13: ioport 0xdc00 alloc failed ahc_isa_probe 14: ioport 0xec00 alloc failed sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xc8fff,0xec000-0xeffff pnpid ORM0000 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0 ata0: reset tp1 mask=00 ostat0=ff ostat1=ff ioapic0: routing intpin 14 (ISA IRQ 14) to vector 56 ata0: [MPSAFE] ata1 at port 0x170-0x177,0x376 irq 15 on isa0 ata1: reset tp1 mask=00 ostat0=ff ostat1=ff ioapic0: routing intpin 15 (ISA IRQ 15) to vector 57 ata1: [MPSAFE] bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fe0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) ppc0: parallel port not found. ppc0: <Parallel port> failed to probe at irq 7 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0x4c03 0x4c03 0x4c03 0x4c03 sio0: probe failed test(s): 0 1 2 4 6 7 9 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0x4c03 0x4c03 0x4c03 0x4c03 sio0: probe failed test(s): 0 1 2 4 6 7 9 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 or not responding ioapic0: routing intpin 4 (ISA IRQ 4) to vector 58 sio0: [FAST] sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0x4c03 0x4c03 0x4c03 0x4c03 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. Reducing kern.maxvnodes 214565 -> 100000 procfs registered lapic: Divisor 2, Frequency 166251043 hz Timecounter "TSC" frequency 1995012030 Hz quality -100 Timecounters tick every 1.000 msec lo0: bpf attached rr232x: no controller detected. (probe0:mpt0:0:0:0): error 22 (probe0:mpt0:0:0:0): Unretryable Error (probe0:mpt0:0:0:0): error 22 (probe0:mpt0:0:0:0): Unretryable Error (probe0:mpt0:0:0:1): error 22 (probe0:mpt0:0:0:1): Unretryable Error (probe0:mpt0:0:0:2): error 22 (probe0:mpt0:0:0:2): Unretryable Error (probe0:mpt0:0:0:3): error 22 (probe0:mpt0:0:0:3): Unretryable Error (probe0:mpt0:0:0:4): error 22 (probe0:mpt0:0:0:4): Unretryable Error (probe0:mpt0:0:0:5): error 22 (probe0:mpt0:0:0:5): Unretryable Error (probe0:mpt0:0:0:6): error 22 (probe0:mpt0:0:0:6): Unretryable Error (probe0:mpt0:0:0:7): error 22 (probe0:mpt0:0:0:7): Unretryable Error (probe8:mpt0:0:8:0): error 22 (probe8:mpt0:0:8:0): Unretryable Error (probe8:mpt0:0:8:0): error 22 (probe8:mpt0:0:8:0): Unretryable Error (probe63:umass-sim0:0:0:0): Down reving Protocol Version from 2 to 0? (probe63:umass-sim0:0:0:0): Uninitialized Transport 5:c6791bd0? ses0 at mpt0 bus 0 target 8 lun 0 ses0: <DP BACKPLANE 1.00> Fixed Enclosure Services SCSI-5 device ses0: 300.000MB/s transfers ses0: SCSI-3 SES Device pass0 at mpt0 bus 0 target 0 lun 0 pass0: <Dell VIRTUAL DISK 1028> Fixed Direct Access SCSI-5 device pass0: 300.000MB/s transfers pass0: Command Queueing Enabled pass1 at mpt0 bus 0 target 8 lun 0 pass1: <DP BACKPLANE 1.00> Fixed Enclosure Services SCSI-5 device pass1: 300.000MB/s transfers pass2 at umass-sim0 bus 0 target 0 lun 0 pass2: <ST375064 0A 3.AA> Fixed Direct Access SCSI-0 device pass2: Serial Number 3QD0LVJJ pass2: 40.000MB/s transfers da0 at mpt0 bus 0 target 0 lun 0 da0: <Dell VIRTUAL DISK 1028> Fixed Direct Access SCSI-5 device da0: 300.000MB/s transfers da0: Command Queueing Enabled da0: 69618MB (142577664 512 byte sectors: 255H 63S/T 8875C) GEOM: new disk da0da1 at umass-sim0 bus 0 target 0 lun 0 da1: <ST375064 0A 3.AA> Fixed Direct Access SCSI-0 device da1: Serial Number 3QD0LVJJ da1: 40.000MB/s transfers da1: 715404MB (1465149168 512 byte sectors: 255H 63S/T 91201C) GEOM: new disk da1 ATA PseudoRAID loaded SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000200ef therm: 0x00010000 err: 0x00010000 pcm: 0x00010000 ioapic0: Assigning ISA IRQ 1 to local APIC 0 ioapic0: Assigning ISA IRQ 4 to local APIC 1 ioapic0: Assigning ISA IRQ 9 to local APIC 0 ioapic0: Assigning ISA IRQ 12 to local APIC 1 ioapic0: Assigning ISA IRQ 14 to local APIC 0 ioapic0: Assigning ISA IRQ 15 to local APIC 1 ioapic0: Assigning PCI IRQ 20 to local APIC 0 ioapic0: Assigning PCI IRQ 21 to local APIC 1 ioapic2: Assigning PCI IRQ 192 to local APIC 0 msi: Assigning MSI IRQ 256 to local APIC 1 msi: Assigning MSI IRQ 257 to local APIC 0 Trying to mount root from ufs:/dev/da0s1a WARNING: / was not properly dismounted start_init: trying /sbin/init WARNING: /tmp was not properly dismounted WARNING: /usr was not properly dismounted WARNING: /var was not properly dismounted
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:05 UTC