At 12:27 AM 7/18/2007, Kip Macy wrote: >You need to use the module in order to update the firmware. The >firmware will be automatically be updated when you up an interface on >the card. Thanks, I just figured that out a few min ago by accident and the card looks happy now! [leopard1]% ifconfig cxgb0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 9000 options=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4> ether 00:07:43:04:01:2c inet 192.168.10.1 netmask 0xffffff00 broadcast 192.168.10.255 media: Ethernet 10Gbase-CX4 <full-duplex> (autoselect <full-duplex>) status: active [leopard1]% sysctl -a | grep cxg hw.cxgb.singleq: 1 hw.cxgb.ofld_disable: 0 hw.cxgb.msi_allowed: 2 dev.cxgbc.0.%desc: Chelsio T310 RNIC, 1 port dev.cxgbc.0.%driver: cxgbc dev.cxgbc.0.%location: slot=0 function=0 dev.cxgbc.0.%pnpinfo: vendor=0x1425 device=0x0030 subvendor=0x1425 subdevice=0x0001 class=0x020000 dev.cxgbc.0.%parent: pci10 dev.cxgbc.0.firmware_version: 4.5.0 dev.cxgbc.0.intr_coal: 5000 dev.cxgbc.0.enable_debug: 0 dev.cxgbc.0.collapse_free: 0 dev.cxgbc.0.mb_free_vec_free: 0 dev.cxgbc.0.collapse_mbufs: 0 dev.cxgbc.0.txq_overrun: 0 dev.cxgbc.0.bogus_imm: 1 dev.cxgb.0.%desc: Port 0 10GBASE-CX4 dev.cxgb.0.%driver: cxgb dev.cxgb.0.%parent: cxgbc0 [leopard1]% > -Kip > >On 7/17/07, Mike Tancsa <mike_at_sentex.net> wrote: >>Hi, >> >>I am trying to run a recent current with the Chelsio 10GigE card >>below and it tries to load but has the following complaint. >> >>cxgbc0: <Chelsio T310 RNIC, 1 port> mem >>0xe0201000-0xe0201fff,0xe0800000-0xe0ffffff,0xe0200000-0xe0200fff irq >>16 at device 0.0 on pci10 >>cxgbc0: found wrong FW version (4.0), driver needs version 4.5 >>cxgbc0: firmware needs to be updated to version 4.5.0 >>cxgbc0: found wrong TP version (0.0), driver needs version 1.1 >>cxgbc0: SRAM needs to be updated to version b-1.1.0 >>cxgb0: <Port 0 10GBASE-CX4> on cxgbc0 >>cxgb0: Ethernet address: 00:07:43:04:01:2c >> >>Where do I get the firmware from ? The website only has 4.3 ? Also, >>how do I update the SRAM. Sorry if these are obvious questions, but >>I am new to CURRENT with such drivers. I have the driver compiled >>into the kernel >> >> >>With the Myricom, it seems to work, but it doesnt detect the cx4 >>media type for some reason. >> >># ifconfig mxge0 >>mxge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 9000 >> >>options=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4> >> ether 00:60:dd:47:c6:c4 >> inet 192.168.10.3 netmask 0xffffff00 broadcast 192.168.10.255 >> media: <unknown type> (autoselect <full-duplex>) >> status: active >> >>The port is up and I can ping across it so it is working. >> >>TenGigabitEthernet2/3 is up, line protocol is up (connected) >> Hardware is C6k 10000Mb 802.3, address is 0018.bab0.2036 (bia >>0018.bab0.2036) >> Description: leopard3 mxge0 >> MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec, >> reliability 255/255, txload 1/255, rxload 1/255 >> Encapsulation ARPA, loopback not set >> Full-duplex, 10Gb/s >> input flow-control is off, output flow-control is on >> ARP type: ARPA, ARP Timeout 04:00:00 >> Last input never, output 00:00:55, output hang never >> Last clearing of "show interface" counters never >> Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0 >> Queueing strategy: fifo >> Output queue: 0/40 (size/max) >> 5 minute input rate 0 bits/sec, 0 packets/sec >> 5 minute output rate 0 bits/sec, 0 packets/sec >> 8 packets input, 588 bytes, 0 no buffer >> Received 5 broadcasts, 0 runts, 0 giants, 0 throttles >> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored >> 0 input packets with dribble condition detected >> 403 packets output, 30468 bytes, 0 underruns >> 0 output errors, 0 collisions, 1 interface resets >> 0 babbles, 0 late collision, 0 deferred >> 0 lost carrier, 0 no carrier >> 0 output buffer failures, 0 output buffers swapped out >> >> >> ---Mike >> >> >>-------------------------------------------------------------------- >>Mike Tancsa, tel +1 519 651 3400 >>Sentex Communications, mike_at_sentex.net >>Providing Internet since 1994 www.sentex.net >>Cambridge, Ontario Canada www.sentex.net/mike >> >>_______________________________________________ >>freebsd-current_at_freebsd.org mailing list >>http://lists.freebsd.org/mailman/listinfo/freebsd-current >>To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"Received on Wed Jul 18 2007 - 02:34:28 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:14 UTC