I didn't notice this issue until now. So I don't know when this issue started. The issue is that I can't attach floppy disk drive. I doesn't disable FDC on BIOS, and I can boot from floppy disk. What should I do? # kldload fdc fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: [FILTER] device_attach: fdc0 attach returned 12 fdc1: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc1: [FILTER] device_attach: fdc1 attach returned 12 # uname -a FreeBSD nadesico.ninth-nine.com 7.0-CURRENT FreeBSD 7.0-CURRENT #61: Thu Jun 14 14:39:24 JST 2007 nork_at_nadesico.ninth-nine.com:/usr/obj/usr/src/sys/NADESICO i386 # dmesg Copyright (c) 1992-2007 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.0-CURRENT #61: Thu Jun 14 14:39:24 JST 2007 nork_at_nadesico.ninth-nine.com:/usr/obj/usr/src/sys/NADESICO acpi_alloc_wakeup_handler: can't alloc wake memory Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Pentium(R) III CPU family 1133MHz (1188.97-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6b1 Stepping = 1 Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE> real memory = 2147418112 (2047 MB) avail memory = 2095558656 (1998 MB) ACPI APIC Table: <VIA694 AWRDACPI> FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 ioapic0 <Version 1.1> irqs 0-23 on motherboard kbd1 at kbdmux0 smbios0: <System Management BIOS> at iomem 0xf13e0-0xf13fe on motherboard smbios0: Version: 2.3, BCD Revision: 2.3 cryptosoft0: <software crypto> on motherboard acpi0: <VIA694 AWRDACPI> on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of f0000, 4000 (3) failed acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 7fef0000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0 cpu0: <ACPI CPU> on acpi0 cpu1: <ACPI CPU> on acpi0 acpi_button0: <Power Button> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff,0x4000-0x407f,0x4080-0x40ff,0x5000-0x500f on acpi0 pci0: <ACPI PCI bus> on pcib0 agp0: <VIA 8633 (Pro 266) host to PCI bridge> on hostb0 pcib1: <PCI-PCI bridge> at device 1.0 on pci0 pci1: <PCI bus> on pcib1 vgapci0: <VGA-compatible display> port 0x9000-0x90ff mem 0xd0000000-0xdfffffff,0xf9000000-0xf900ffff irq 16 at device 0.0 on pci1 vgapci1: <VGA-compatible display> mem 0xe0000000-0xefffffff,0xf9010000-0xf901ffff at device 0.1 on pci1 uhci0: <VIA 83C572 USB controller> port 0xa000-0xa01f irq 17 at device 7.0 on pci0 uhci0: [GIANT-LOCKED] uhci0: [ITHREAD] usb0: <VIA 83C572 USB controller> on uhci0 usb0: USB revision 1.0 uhub0: <VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 2 ports with 2 removable, self powered uhci1: <VIA 83C572 USB controller> port 0xa400-0xa41f irq 18 at device 7.1 on pci0 uhci1: [GIANT-LOCKED] uhci1: [ITHREAD] usb1: <VIA 83C572 USB controller> on uhci1 usb1: USB revision 1.0 uhub1: <VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 uhub1: 2 ports with 2 removable, self powered ehci0: <VIA VT6202 USB 2.0 controller> mem 0xfb117000-0xfb1170ff irq 19 at device 7.2 on pci0 ehci0: [GIANT-LOCKED] ehci0: [ITHREAD] usb2: EHCI version 1.0 usb2: companion controllers, 2 ports each: usb0 usb1 usb2: <VIA VT6202 USB 2.0 controller> on ehci0 usb2: USB revision 2.0 uhub2: <VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2 uhub2: 4 ports with 4 removable, self powered pcm0: <ESS Technology Maestro3> port 0xa800-0xa8ff mem 0xfb112000-0xfb113fff irq 18 at device 8.0 on pci0 pcm0: [ITHREAD] pcm0: <SigmaTel STAC9744/45 AC97 Codec> fwohci0: <Texas Instruments TSB82AA2> mem 0xfb115000-0xfb1157ff,0xfb108000-0xfb10bfff irq 19 at device 9.0 on pci0 fwohci0: [FILTER] fwohci0: OHCI version 1.10 (ROM=1) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 01:d2:00:00:04:23:01:b4 fwohci0: invalid speed 7 (fixed to 3). fwohci0: Phy 1394a available S800, 3 ports. fwohci0: Link S800, max_rec 4096 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:d2:00:23:01:b4 fwe0: Ethernet address: 02:d2:00:23:01:b4 sbp0: <SBP-2/SCSI over FireWire> on firewire0 dcons_crom0: <dcons configuration ROM> on firewire0 dcons_crom0: bus_addr 0x48000 fwohci0: Initiate bus reset fwohci0: BUS reset fwohci0: node_id=0x8800ffc0, gen=1, non CYCLEMASTER mode hifn0 mem 0xfb114000-0xfb114fff,0xfb10e000-0xfb10ffff,0xfb100000-0xfb107fff irq 16 at device 10.0 on pci0 hifn0: [ITHREAD] hifn0: Hifn 7955, rev 0, 32KB dram, pll=0x801<ext clk, 4x mult> sym0: <1010-33> port 0xac00-0xacff mem 0xfb119000-0xfb1193ff,0xfb10c000-0xfb10dfff irq 17 at device 11.0 on pci0 sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: handling phase mismatch from SCRIPTS. sym0: SCAN AT BOOT disabled for targets 0 1 2 3 4 5 6 8 9 10 11 12 13 14 15. sym0: SCAN FOR LUNS disabled for targets 0 1 2 3 4 5 6 8 9 10 11 12 13 14 15. sym0: [GIANT-LOCKED] sym0: [ITHREAD] sym1: <1010-33> port 0xb000-0xb0ff mem 0xfb116000-0xfb1163ff,0xfb110000-0xfb111fff irq 17 at device 11.1 on pci0 sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking sym1: open drain IRQ line driver, using on-chip SRAM sym1: using LOAD/STORE-based firmware. sym1: handling phase mismatch from SCRIPTS. sym1: SCAN AT BOOT disabled for targets 1 2 3 4 5 6 8 9 10 11 12 13 14 15. sym1: SCAN FOR LUNS disabled for targets 0 1 2 3 4 5 6 8 9 10 11 12 13 14 15. sym1: [GIANT-LOCKED] sym1: [ITHREAD] pci0: <network, ethernet> at device 13.0 (no driver attached) isab0: <PCI-ISA bridge> at device 17.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <VIA 8233 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xb800-0xb80f at device 17.1 on pci0 ata0: <ATA channel 0> on atapci0 ata0: [ITHREAD] ata1: <ATA channel 1> on atapci0 ata1: [ITHREAD] uhci2: <VIA 83C572 USB controller> port 0xbc00-0xbc1f irq 10 at device 17.2 on pci0 uhci2: [GIANT-LOCKED] uhci2: [ITHREAD] usb3: <VIA 83C572 USB controller> on uhci2 usb3: USB revision 1.0 uhub3: <VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3 uhub3: 2 ports with 2 removable, self powered uhci3: <VIA 83C572 USB controller> port 0xc000-0xc01f irq 10 at device 17.3 on pci0 uhci3: [GIANT-LOCKED] uhci3: [ITHREAD] usb4: <VIA 83C572 USB controller> on uhci3 usb4: USB revision 1.0 uhub4: <VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4 uhub4: 2 ports with 2 removable, self powered uhci4: <VIA 83C572 USB controller> port 0xc400-0xc41f irq 10 at device 17.4 on pci0 uhci4: [GIANT-LOCKED] uhci4: [ITHREAD] usb5: <VIA 83C572 USB controller> on uhci4 usb5: USB revision 1.0 uhub5: <VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb5 uhub5: 2 ports with 2 removable, self powered acpi_tz0: <Thermal Zone> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xc0000-0xccfff,0xd0000-0xd3fff pnpid ORM0000 on isa0 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> ums0: <Logitech USB Mouse, class 0/0, rev 1.10/6.20, addr 2> on uhub3 ums0: 3 buttons and Z dir. WARNING: ZFS is considered to be an experimental feature in FreeBSD. Timecounters tick every 1.000 msec firewire0: 3 nodes, maxhop <= 2, cable IRM = 2 ZFS filesystem version 6 ZFS storage pool version 6 ad0: 78533MB <HDS728080PLAT20 PF2OA21B> at ata0-master UDMA100 ad1: 238475MB <I-O DATA NAKA-HDRM 2.10.8> at ata1-master UDMA100 (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered. (noperiph:sym1:0:-1:-1): SCSI BUS reset delivered. fwohci0: txd err= 3 miss Ack err firewire0: New S400 device ID:00110600000039bd fwohci0: txd err= 3 miss Ack err fwohci0: txd err= 3 miss Ack err GEOM_LABEL: Label for provider ad1 is ufs/HDS250G. SMP: AP CPU #1 Launched! da0 at sym1 bus 0 target 0 lun 0 da0: <IBM DNES-318350W SA30> Fixed Direct Access SCSI-3 device da0: 40.000MB/s transfers (20.000MHz, offset 31, 16bit) da0: Command Queueing Enabled da0: 17501MB (35843670 512 byte sectors: 255H 63S/T 2231C) Trying to mount root from ufs:/dev/ad0s1a tap0: Ethernet address: 00:bd:ae:31:00:00 tap1: Ethernet address: 00:bd:b4:31:00:01 tap2: Ethernet address: 00:bd:b7:31:00:02 drm0: <ATI Radeon AP 9600> on vgapci0 info: [drm] AGP at 0xf0000000 128MB info: [drm] Initialized radeon 1.25.0 20060524 info: [drm] Setting GART location based on new memory map info: [drm] Loading R300 Microcode info: [drm] writeback test succeeded in 1 usecs drm0: [ITHREAD] pid 8570 (scim-helper-manager), uid 1001: exited on signal 11 fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fdc0: [FILTER] device_attach: fdc0 attach returned 12 fdc1: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0 fdc1: [FILTER] device_attach: fdc1 attach returned 12Received on Thu Jun 14 2007 - 13:56:55 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:12 UTC