Re: yongari nfe problems

--- Pyun YongHyeon <pyunyh_at_gmail.com> wrote:

> On Fri, Mar 09, 2007 at 08:08:56PM +0900, To Mr.
> Darren wrote:
>  > On Thu, Mar 08, 2007 at 04:33:36PM -0800, Mr.
> Darren wrote:
>  >  > I tried the following overhauled nfe drivers
> after no
>  >  > success in getting nfe to work with my
> hardware.  
>  >  > >
> http://people.freebsd.org/~yongari/nfe/if_nfe.c
>  >  > >  > >  > > >
>  >  > >
> http://people.freebsd.org/~yongari/nfe/if_nfereg.h
>  >  > >  > >  > > >
>  >  > >
> http://people.freebsd.org/~yongari/nfe/if_nfevar.h
>  >  > 
>  >  > It still doesn't work, but I have a new set of
> errors.
>  >  > 
>  >  > nfe0: <NVIDIA nForce MCP55 Networking Adapter>
> port
>  >  > 0xb000-0xb007 mem
>  >  >
>
0xfe02a000-0xfe02afff,0xfe029000-0xfe0290ff,0xfe028000-0xfe02800f
>  >  > irq 10 at device 16.0 on pci0
>  >  > nfe0: Ethernet address: 00:15:f2:f4:af:5e
>  >  > miibus1: <MII bus> on nfe0
>  >  > nfe0: [ITHREAD]
>  >  > nfe1: <NVIDIA nForce MCP55 Networking Adapter>
> port
>  >  > 0xac00-0xac07 mem
>  >  >
>
0xfe027000-0xfe027fff,0xfe026000-0xfe0260ff,0xfe025000-0xfe02500f
>  >  > irq 11 at device 17.0 on pci0
>  >  > nfe1: Ethernet address: 00:15:f2:f4:af:5f
>  >  > miibus2: <MII bus> on nfe1
>  >  > nfe1: [ITHREAD]
>  >  > nfe0: link state changed to DOWN
>  >  > nfe0: link state changed to UP
>  >  > nfe0: watchdog timeout (missed Tx interrupts)
> --
>  >  > recovering
>  >  > nfe0: watchdog timeout (missed Tx interrupts)
> --
>  >  > recovering
>  >  > 
>  > 
>  > According to Shigeaki Tagashira'page nForce 590
> is supported by
>  > nfe(4). ATM I have no idea why it shows watchdog
> timeout errors.
>  > Btw, I don't see what PHY driver was attached in
> your message.
>  > (You can check it with dmesg(8) and normally it
> would pick up
>  > e1000phy(4).)
>  > 
> 
> Oops, I think I've posted wrong version.
> Please re-fetch and try again.
> 
>  >  > 
>  >  > the missing tx interrupts were made while
> trying
>  >  > /sbin/dhclient nfe0
>  >  > 
>  >  > My motherboard is the ASUS crosshair NVIDIA
> nForce 590
>  >  > FreeBSD DARREN 7.0-CURRENT FreeBSD 7.0-CURRENT
> #12:
>  >  > Thu Mar  8 16:57:38 UTC 2007    
>  >  > root_at_DARREN:/usr/obj/usr/src/sys/DARREN  amd64
>  >  > the cvsup this kernel was compiled with is
> less than 1
>  >  > week old.
>  >  > 
>  >  > -Darren
>  > -- 
>  > Regards,
>  > Pyun YongHyeon
> 
> -- 
> Regards,
> Pyun YongHyeon
> 


e1000phy0: <Marvell 88E1116 Gigabit PHY> PHY 1 on
miibus1
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX,
100baseTX-FDX, 1000baseTX-FDX, auto
e1000phy1: <Marvell 88E1116 Gigabit PHY> PHY 1 on
miibus2
e1000phy1:  10baseT, 10baseT-FDX, 100baseTX,
100baseTX-FDX, 1000baseTX-FDX, auto

same problem with the new driver downloaded from 
http://people.freebsd.org/~yongari/nfe/ .  again,
while /sbin/dhclient nfe0 while in communication to my
router.

nfe0: link state changed to DOWN
nfe0: link state changed to UP
nfe0: watchdog timeout (missed Tx interrupts) --
recovering
nfe0: watchdog timeout (missed Tx interrupts) --
recovering
nfe0: watchdog timeout (missed Tx interrupts) --
recovering
nfe0: watchdog timeout (missed Tx interrupts) --
recovering
nfe0: watchdog timeout (missed Tx interrupts) --
recovering



 
____________________________________________________________________________________
8:00? 8:25? 8:40? Find a flick in no time 
with the Yahoo! Search movie showtime shortcut.
http://tools.search.yahoo.com/shortcuts/#news