Re: CFT: nfe(4) MSI/MSIX support

On Wed, May 09, 2007 at 10:19:47PM +0200, Rainer Hurling wrote:
 > Hello Pyun YongHyeon,
 > 
 > my mainboard is K9N Neo from MSI with BIOS version 1.60.
 > 
 > I compiled CURRENT from 05/09/07 on i386 with your new if_nfe files and
 > your patch for ciphy (/usr/src/sys/dev/mii). Before, I had to use 
 > polling mode with nfe(4), now this is not neccessary any more :-)
 > 
 > 
 > boot -v gives me:
 > -------------------
 > pcib0: slot 1 INTA routed to irq 20 via \\_SB_.LSMB
 > MSI supports 4 messages, 64 bit
 > ...
 > pcib0: slot 5 INTA routed to irq 23 via \\_SB_.LSA0
 > MSI supports 4 messages, 64 bit
 > ...
 > pcib0: slot 5 INTB routed to irq 20 via \\_SB_.LSA1
 > MSI supports 1 message, 64 bit, vector masks
 > ...
 > pcib0: slot 6 INTB routed to irq 21 via \\_SB_.LAZA
 > MSI supports 8 messages, 64 bit, vector masks
 > MSI-X supports 8 messages in maps 0x18 and 0x1c
 > ...
 > pcib0: slot 8 INTA routed to irq 22 via \\_SB_.LMAC
 > MSI supports 2 messages, 64 bit
 > MSI supports 2 messages, 64 bit
 > MSI supports 2 messages, 64 bit
 > MSI supports 2 messages, 64 bit
 > MSI supports 2 messages, 64 bit
 > ...
 > pci6: physical bus=6
 > MSI supports 1 message, 64 bit
 > ...
 > nfe0: <NVIDIA nForce MCP55 Networking Adapter> port 0xb000-0xb007 mem
 > 0xfbef3000-0xfbef3fff,0xfbefa800-0xfbefa8ff,0
 > xfbefa400-0xfbefa40f irq 22 at device 8.0 on pci0
 > nfe0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xfbef3000
 > nfe0: attempting to allocate 8 MSI vectors (8 supported)
 > msi: routing MSI IRQ 256 to vector 56
 > msi: routing MSI IRQ 257 to vector 57
 > msi: routing MSI IRQ 258 to vector 58
 > msi: routing MSI IRQ 259 to vector 59
 > msi: routing MSI IRQ 260 to vector 60
 > msi: routing MSI IRQ 261 to vector 61
 > msi: routing MSI IRQ 262 to vector 62
 > msi: routing MSI IRQ 263 to vector 63
 > nfe0: using IRQs 256-263 for MSI
 > nfe0: Using 8 MSI messages
 > miibus0: <MII bus> on nfe0
 > ciphy0: <VSC8601 10/100/1000TX PHY> PHY 1 on miibus0
 > ciphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
 > 1000baseT-FDX, auto
 > nfe0: bpf attached
 > nfe0: Ethernet address: xx:xx:xx:xx:xx:xx
 > nfe0: [MPSAFE]
 > nfe0: [FILTER]
 > nfe0: [MPSAFE]
 > nfe0: [FILTER]
 > nfe0: [MPSAFE]
 > nfe0: [FILTER]
 > nfe0: [MPSAFE]
 > nfe0: [FILTER]
 > nfe0: [MPSAFE]
 > nfe0: [FILTER]
 > nfe0: [MPSAFE]
 > nfe0: [FILTER]
 > nfe0: [MPSAFE]
 > nfe0: [FILTER]
 > nfe0: [MPSAFE]
 > nfe0: [FILTER]
 > ...
 > msi: Assigning MSI IRQ 256 to local APIC 0
 > msi: Assigning MSI IRQ 257 to local APIC 1
 > msi: Assigning MSI IRQ 258 to local APIC 0
 > msi: Assigning MSI IRQ 259 to local APIC 1
 > msi: Assigning MSI IRQ 260 to local APIC 0
 > msi: Assigning MSI IRQ 261 to local APIC 1
 > msi: Assigning MSI IRQ 262 to local APIC 0
 > msi: Assigning MSI IRQ 263 to local APIC 1
 > -------------------
 > 
 > 
 > It seems that everything is alright know.

Ok, thanks a lot for testing!
 > 
 > Thank you very much,

You're welcome!

 > Rainer
 > 

-- 
Regards,
Pyun YongHyeon