-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 > On Fri, 2007-10-26 at 22:34 +0200, Szymon Kozak wrote: >> / On 10/25/07, JoaoBR <joao at matik.com.br >> <http://lists.freebsd.org/mailman/listinfo/freebsd-current>> >> wrote: > />/ > > The main goal of the two technologies is the same, i.e., > out-of-band />/ > > server management. Both use Remote Management > and Control Protocol />/ > > (RMCP) for the network protocol but > ASF is implemented on NIC />/ > > firmware level while IPMI is > implemented on baseboard management />/ > > controller (BMC). Now > BCM57xx firmware has built-in ASF stack and />/ > > the interface > can be shared with BMC. If there is a BMC on-board and />/ > > > network controller is shared, obviously you cannot just reset the > />/ > > controller, etc. You have to 'tell' the firmware that you > are about />/ > > to do critical things, such as reset, start, > stop, link negotiation, />/ > > etc, so that it can communicate > with BMC beforehand. If you turn on />/ > > hw.bge.allow_asf, it > does just that. Unfortunately, it does not work />/ > > for all > systems in the real world because they are not created equal, />/ > > > e.g., different spec. revisions, hardware implementations, > firmware, />/ > > BIOS, etc. Basically some system fails *without* > it while some />/ > > system fails *with* it. Hence, the tunable > was necessary. At least, />/ > > that is how I understand it. />/ > > />/ > />/ > thank you, that was great />/ > />/ > but would > really not harm to put something about resumed into the man page > />/ > />/ />/ Hello, />/ I have the same problem, but change > value to hw.bge.allow_asf="0" />/ doesn't work for me. />/ I have > Broadcom NetLink (TM) Gigabit Ethernet in my ThinkPad R61. />/ > Dmesg from FreeBSD-STABLE shows: />/ />/ bge0: <Broadcom > BCM5754/5787 A2, ASIC rev. 0xb002> mem />/ 0xfe000000-0xfe00ffff > irq 18 at device 0.0 on pci4 />/ />/ Here is complete dmesg: > http://slane.pl/tmp/dmesg.txt />/ />/ Anybody know what's wrong? / > Hello, > > I've tried again the latest version of if_bge.c on my HP 6710b > laptop with no results, even after setting hw.bge.allow_asf="0". > I've also tried with the debugger and it seems to panic when > calling free() in device_probe_child.c (IIRC). Then I #define'd > BUS_PROBE and the freeze occurs after displaying something like > "devclass_alloc_unit: now: unit 0 in devclass bge". > > The 7 Beta 1.5 install CD hangs also when loading the driver. > > I have a coredump made from whithin the debugger with the exact > place where the faulty free() occurs, so I can provide more exact > info if someone is interested. I just hope this is not a > heisen-bug. > > Best regards, Cristi I have a 6715b that is experiencing the same exact problem. I made a release from 8-CURRENT as of last night and I still see it. Just by chance, I installed my normal kernel (for my other amd64 machine) onto the ISO and re-burned and it worked (since I don't have if_bge on that kernel). After selectively loading/unloading modules I tracked it down to this. Has any more traction been made on the BGE issue here? - -- Coleman Kane -----BEGIN PGP SIGNATURE----- Version: GnuPG v2.0.4 (FreeBSD) Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org iD8DBQFHMdn+cMSxQcXat5cRAufMAJ9R/xRmsY1/XIdq+Vgx9AjO18yiywCfSoY8 Yv+tq/NrUP6Vfd/ihYcCyJ4= =wKt6 -----END PGP SIGNATURE-----Received on Wed Nov 07 2007 - 14:49:55 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:21 UTC