# uname -a FreeBSD dv6000.tddhome 7.0-CURRENT FreeBSD 7.0-CURRENT #4: \ Sat Sep 8 00:21:44 PDT 2007 \ root_at_dv6000.tddhome:/usr/src/sys/GENERIC i386 I have an HP Pavillion dv6446 notebook with -current. The notebook does not have a serial port. Dmesg shows sio. Dmesg from boot -v is below. With a typo, I used tip to connect to cuad0 as a normal user in the dialer group. The system locked up, no response to the keyboard, no response to ping. etc/remote has hw38400:dv=/dev/cuad0:br#38400:pa=none hu38400:dv=/dev/cuaU0:br#38400:pa=none # tip hw38400 connected and, lockup. What additional information may I provide? tomdean # dmesg Copyright (c) 1992-2007 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.0-CURRENT #4: Sat Sep 8 00:21:44 PDT 2007 root_at_dv6000.tddhome:/usr/src/sys/GENERIC WARNING: WITNESS option enabled, expect reduced performance. Preloaded elf kernel "/boot/kernel/kernel" at 0xc0d8c000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc0d8c248. Calibrating clock(s) ... i8254 clock: 1193193 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz quality 0 Calibrating TSC clock ... TSC clock: 1995613575 Hz CPU: Intel(R) Core(TM) Duo CPU T2450 _at_ 2.00GHz (1995.61-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6ec Stepping = 12 Features=0xbfe9fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0xc189<SSE3,MON,EST,TM2,xTPR,PDCM> AMD Features=0x100000<NX> Cores per package: 2 Instruction TLB: 4 KB Pages, 4-way set associative, 128 entries Data TLB: 4 KB Pages, 4-way set associative, 128 entries Instruction TLB: 4 MB pages, fully associative, 2 entries 2nd-level cache: 2-MB, 8-way set associative, 64-byte line size 1st-level instruction cache: 32 KB, 8-way set associative, 64 byte line size Data TLB: 4 MB Pages, 4-way set associative, 8 entries 1st-level data cache: 32 KB, 8-way set associative, 64 byte line size L2 cache: 2048 kbytes, 8-way associative, 64 bytes/line real memory = 2137456640 (2038 MB) Physical memory chunk(s): 0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages) 0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages) 0x0000000001028000 - 0x000000007d24afff, 2082615296 bytes (508451 pages) avail memory = 2082082816 (1985 MB) MP Configuration Table version 1.4 found at 0xc009fd71 Table 'FACP' at 0x7f683bf8 Table 'APIC' at 0x7f683cec MADT: Found table at 0x7f683cec APIC: Using the MADT enumerator. MADT: Found CPU APIC ID 0 ACPI ID 0: enabled SMP: Added CPU 0 (AP) MADT: Found CPU APIC ID 1 ACPI ID 1: enabled SMP: Added CPU 1 (AP) ACPI APIC Table: <HP 30BB > INTR: Adding local APIC 1 as a target FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP): APIC ID: 1 bios32: Found BIOS32 Service Directory header at 0xc00f7cc0 bios32: Entry = 0xfd610 (c00fd610) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xfd610+0x273 pnpbios: Found PnP BIOS data at 0xc00f7d30 pnpbios: Entry = f0000:bde5 Rev = 1.0 Other BIOS signatures found: APIC: CPU 0 has ACPI ID 0 APIC: CPU 1 has ACPI ID 1 ACPI: RSDP _at_ 0x0xf7c60/0x0024 (v 2 HP ) ACPI: XSDT _at_ 0x0x7f67b353/0x0084 (v 1 HPQOEM SLIC-MPC 0x06040000 LTP 0x00000000) ACPI: FACP _at_ 0x0x7f683bf8/0x00F4 (v 3 INTEL CALISTGA 0x06040000 ALAN 0x00000001) ACPI: DSDT _at_ 0x0x7f67c655/0x752F (v 1 HP 30BB 0x06040000 MSFT 0x0100000E) ACPI: FACS _at_ 0x0x7f684fc0/0x0040 ACPI: APIC _at_ 0x0x7f683cec/0x0068 (v 1 HP 30BB 0x06040000 LOHR 0x0000005A) ACPI: HPET _at_ 0x0x7f683d54/0x0038 (v 1 HP 30BB 0x06040000 LOHR 0x0000005A) ACPI: MCFG _at_ 0x0x7f683d8c/0x003C (v 1 HP 30BB 0x06040000 LOHR 0x0000005A) ACPI: TCPA _at_ 0x0x7f683dc8/0x0032 (v 1 HP 30BB 0x06040000 PTL 0x00000001) ACPI: APIC _at_ 0x0x7f683dfa/0x0068 (v 1 HP 30BB 0x06040000 LTP 0x00000000) ACPI: BOOT _at_ 0x0x7f683e62/0x0028 (v 1 HP 30BB 0x06040000 LTP 0x00000001) ACPI: SLIC _at_ 0x0x7f683e8a/0x0176 (v 1 HPQOEM SLIC-MPC 0x06040000 LTP 0x00000001) ACPI: SSDT _at_ 0x0x7f67c44b/0x020A (v 1 HP 30BB 0x00001000 INTL 0x20050624) ACPI: SSDT _at_ 0x0x7f67b963/0x025F (v 1 HP 30BB 0x00003000 INTL 0x20050624) ACPI: SSDT _at_ 0x0x7f67b8bd/0x00A6 (v 1 HP 30BB 0x00003000 INTL 0x20050624) ACPI: SSDT _at_ 0x0x7f67b3d7/0x04E6 (v 1 HP 30BB 0x00003000 INTL 0x20050624) MADT: Found IO APIC ID 1, Interrupt 0 at 0xfec00000 ioapic0: Changing APIC ID to 1 ioapic0: Routing external 8259A's -> intpin 0 MADT: Interrupt override: source 0, irq 2 ioapic0: Routing IRQ 0 -> intpin 2 MADT: Interrupt override: source 9, irq 9 ioapic0: intpin 9 trigger: level lapic0: Routing NMI -> LINT1 lapic0: LINT1 trigger: edge lapic0: LINT1 polarity: high lapic1: Routing NMI -> LINT1 lapic1: LINT1 trigger: edge lapic1: LINT1 polarity: high ioapic0 <Version 2.0> irqs 0-23 on motherboard cpu0 BSP: ID: 0x00000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000100ef therm: 0x00000200 err: 0x00010000 pcm: 0x00010000 wlan: <802.11 Link Layer> ath_rate: version 1.2 <SampleRate bit-rate selection algorithm> wlan_amrr: <AMRR Transmit Rate Control Algorithm> random: <entropy source, Software, Yarrow> nfslock: pseudo-device kbd: new array size 4 kbd1 at kbdmux0 mem: <memory> Pentium Pro MTRR support enabled io: <I/O> null: <null device, zero device> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) rr232x: RocketRAID 232x controller driver v1.02 (Sep 8 2007 00:21:27) npx0: INT 16 interface acpi0: <HPQOEM SLIC-MPC> on motherboard ioapic0: routing intpin 9 (ISA IRQ 9) to vector 48 acpi0: [MPSAFE] acpi0: [ITHREAD] acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 acpi_hpet0: vend: 0x8086 rev: 0x1 num: 1 hz: 14318180 opts: leg_route count_size Timecounter "HPET" frequency 14318180 Hz quality 900 acpi0: Power Button (fixed) acpi0: wakeup code va 0xd906f000 pa 0x1000 pci_open(1): mode 1 addr port (0x0cf8) is 0x8000fa20 pci_open(1a): mode1res=0x80000000 (0x80000000) pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=27a08086) pcibios: BIOS version 2.10 AcpiOsDerivePciId: \\_SB_.PCI0.HBUS -> bus 0 dev 0 func 0 AcpiOsDerivePciId: \\_SB_.PCI0.RP02.P2CS -> bus 0 dev 28 func 1 AcpiOsDerivePciId: \\_SB_.PCI0.RP03.P3CS -> bus 0 dev 28 func 2 AcpiOsDerivePciId: \\_SB_.PCI0.LPCB.LPC0 -> bus 0 dev 31 func 0 acpi0: reservation of fed00000, 400 (3) failed ACPI timer: 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 1/1 -> 10 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0 acpi_ec0: <Embedded Controller: GPE 0x17> port 0x62,0x66 on acpi0 pci_link0: Index IRQ Rtd Ref IRQs Initial Probe 0 11 N 0 11 Validation 0 11 N 0 11 After Disable 0 255 N 0 11 pci_link1: Index IRQ Rtd Ref IRQs Initial Probe 0 3 N 0 3 Validation 0 3 N 0 3 After Disable 0 255 N 0 3 pci_link2: Index IRQ Rtd Ref IRQs Initial Probe 0 3 N 0 3 Validation 0 3 N 0 3 After Disable 0 255 N 0 3 pci_link3: Index IRQ Rtd Ref IRQs Initial Probe 0 4 N 0 4 Validation 0 4 N 0 4 After Disable 0 255 N 0 4 pci_link4: Index IRQ Rtd Ref IRQs Initial Probe 0 10 N 0 10 Validation 0 10 N 0 10 After Disable 0 255 N 0 10 pci_link5: Index IRQ Rtd Ref IRQs Initial Probe 0 255 N 0 11 Validation 0 255 N 0 11 After Disable 0 255 N 0 11 pci_link6: Index IRQ Rtd Ref IRQs Initial Probe 0 5 N 0 5 Validation 0 5 N 0 5 After Disable 0 255 N 0 5 pci_link7: Index IRQ Rtd Ref IRQs Initial Probe 0 7 N 0 7 Validation 0 7 N 0 7 After Disable 0 255 N 0 7 cpu0: <ACPI CPU> on acpi0 ACPI: SSDT _at_ 0x0x7f67c109/0x027A (v 1 HP 30BB 0x00003000 INTL 0x20050624) ACPI: SSDT _at_ 0x0x7f67bbc2/0x04C2 (v 1 HP 30BB 0x00003001 INTL 0x20050624) est0: <Enhanced SpeedStep Frequency Control> on cpu0 p4tcc0: <CPU Frequency Thermal Control> on cpu0 cpu1: <ACPI CPU> on acpi0 ACPI: SSDT _at_ 0x0x7f67c383/0x00C8 (v 1 HP 30BB 0x00003000 INTL 0x20050624) ACPI: SSDT _at_ 0x0x7f67c084/0x0085 (v 1 HP 30BB 0x00003000 INTL 0x20050624) est1: <Enhanced SpeedStep Frequency Control> on cpu1 p4tcc1: <CPU Frequency Thermal Control> on cpu1 acpi_button0: <Power Button> on acpi0 acpi_button1: <Sleep Button> on acpi0 acpi_acad0: <AC Adapter> on acpi0 battery0: <ACPI Control Method Battery> on acpi0 acpi_lid0: <Control Method Lid Switch> on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pci0: physical bus=0 found-> vendor=0x8086, dev=0x27a0, revid=0x03 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0106, statreg=0x2090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x27a2, revid=0x03 bus=0, slot=2, func=0 class=03-00-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 1 message map[10]: type Memory, range 32, base 0xd8100000, size 19, enabled map[14]: type I/O Port, range 32, base 0x1800, size 3, enabled map[18]: type Prefetchable Memory, range 32, base 0xc0000000, size 28, enabled map[1c]: type Memory, range 32, base 0xd8200000, size 18, enabled pcib0: matched entry for 0.2.INTA pcib0: slot 2 INTA hardwired to IRQ 16 found-> vendor=0x8086, dev=0x27a6, revid=0x03 bus=0, slot=2, func=1 class=03-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) powerspec 2 supports D0 D3 current D0 map[10]: type Memory, range 32, base 0xd8180000, size 19, enabled found-> vendor=0x8086, dev=0x27d8, revid=0x02 bus=0, slot=27, func=0 class=04-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=5 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type Memory, range 64, base 0xd8240000, size 14, enabled pcib0: matched entry for 0.27.INTA pcib0: slot 27 INTA hardwired to IRQ 22 found-> vendor=0x8086, dev=0x27d0, revid=0x02 bus=0, slot=28, func=0 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) intpin=a, irq=3 powerspec 2 supports D0 D3 current D0 MSI supports 1 message pcib0: matched entry for 0.28.INTA pcib0: slot 28 INTA hardwired to IRQ 17 found-> vendor=0x8086, dev=0x27d2, revid=0x02 bus=0, slot=28, func=1 class=06-04-00, hdrtype=0x01, mfdev=1 cmdreg=0x0007, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns) intpin=b, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 1 message pcib0: matched entry for 0.28.INTB pcib0: slot 28 INTB hardwired to IRQ 16 found-> vendor=0x8086, dev=0x27c8, revid=0x02 bus=0, slot=29, func=0 class=0c-03-00, hdrtype=0x00, mfdev=1 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=7 map[20]: type I/O Port, range 32, base 0x1820, size 5, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 23 found-> vendor=0x8086, dev=0x27c9, revid=0x02 bus=0, slot=29, func=1 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=10 map[20]: type I/O Port, range 32, base 0x1840, size 5, enabled pcib0: matched entry for 0.29.INTB pcib0: slot 29 INTB hardwired to IRQ 19 found-> vendor=0x8086, dev=0x27ca, revid=0x02 bus=0, slot=29, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=c, irq=3 map[20]: type I/O Port, range 32, base 0x1860, size 5, enabled pcib0: matched entry for 0.29.INTC pcib0: slot 29 INTC hardwired to IRQ 18 found-> vendor=0x8086, dev=0x27cb, revid=0x02 bus=0, slot=29, func=3 class=0c-03-00, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=d, irq=11 map[20]: type I/O Port, range 32, base 0x1880, size 5, enabled pcib0: matched entry for 0.29.INTD pcib0: slot 29 INTD hardwired to IRQ 16 found-> vendor=0x8086, dev=0x27cc, revid=0x02 bus=0, slot=29, func=7 class=0c-03-20, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=7 powerspec 2 supports D0 D3 current D0 map[10]: type Memory, range 32, base 0xd8444000, size 10, enabled pcib0: matched entry for 0.29.INTA pcib0: slot 29 INTA hardwired to IRQ 23 found-> vendor=0x8086, dev=0x2448, revid=0xe2 bus=0, slot=30, func=0 class=06-04-01, hdrtype=0x01, mfdev=0 cmdreg=0x0004, statreg=0x0010, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x27b9, revid=0x02 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 cmdreg=0x0007, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) found-> vendor=0x8086, dev=0x27df, revid=0x02 bus=0, slot=31, func=1 class=01-01-8a, hdrtype=0x00, mfdev=0 cmdreg=0x0005, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=255 map[20]: type I/O Port, range 32, base 0x1810, size 4, enabled found-> vendor=0x8086, dev=0x27c5, revid=0x02 bus=0, slot=31, func=2 class=01-06-01, hdrtype=0x00, mfdev=0 cmdreg=0x0007, statreg=0x02b0, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=4 powerspec 2 supports D0 D3 current D0 MSI supports 1 message map[10]: type I/O Port, range 32, base 0x18d0, size 3, enabled map[14]: type I/O Port, range 32, base 0x18c4, size 2, enabled map[18]: type I/O Port, range 32, base 0x18c8, size 3, enabled map[1c]: type I/O Port, range 32, base 0x18c0, size 2, enabled map[20]: type I/O Port, range 32, base 0x18b0, size 4, enabled map[24]: type Memory, range 32, base 0xd8444400, size 10, enabled pcib0: matched entry for 0.31.INTB pcib0: slot 31 INTB hardwired to IRQ 19 found-> vendor=0x8086, dev=0x27da, revid=0x02 bus=0, slot=31, func=3 class=0c-05-00, hdrtype=0x00, mfdev=0 cmdreg=0x0001, statreg=0x0280, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=4 map[20]: type I/O Port, range 32, base 0x18e0, size 5, enabled pcib0: matched entry for 0.31.INTB pcib0: slot 31 INTB hardwired to IRQ 19 vgapci0: <VGA-compatible display> port 0x1800-0x1807 mem 0xd8100000-0xd817ffff,0xc0000000-0xcfffffff,0xd8200000-0xd823ffff irq 16 at device 2.0 on pci0 agp0: <Intel 82945GM (945GM GMCH) SVGA controller> on vgapci0 vgapci0: Reserved 0x10000000 bytes for rid 0x18 type 3 at 0xc0000000 vgapci0: Reserved 0x80000 bytes for rid 0x10 type 3 at 0xd8100000 vgapci0: Reserved 0x40000 bytes for rid 0x1c type 3 at 0xd8200000 agp0: detected 7932k stolen memory agp0: aperture size is 256M vgapci1: <VGA-compatible display> mem 0xd8180000-0xd81fffff at device 2.1 on pci0 pci0: <multimedia> at device 27.0 (no driver attached) pcib1: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0 pcib1: secondary bus 2 pcib1: subordinate bus 2 pcib1: I/O decode 0x2000-0x2fff pcib1: memory decode 0xd6000000-0xd7ffffff pcib1: prefetched decode 0xd2000000-0xd3ffffff pci2: <ACPI PCI bus> on pcib1 pci2: physical bus=2 found-> vendor=0x8086, dev=0x4222, revid=0x02 bus=2, slot=0, func=0 class=02-80-00, hdrtype=0x00, mfdev=0 cmdreg=0x0006, statreg=0x0010, cachelnsz=16 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=a, irq=11 powerspec 2 supports D0 D3 current D0 MSI supports 1 message, 64 bit map[10]: type Memory, range 32, base 0xd6000000, size 12, enabled pcib1: requested memory range 0xd6000000-0xd6000fff: good pcib1: matched entry for 2.0.INTA pcib1: slot 0 INTA hardwired to IRQ 16 pci2: <network> at device 0.0 (no driver attached) pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.1 on pci0 pcib2: secondary bus 3 pcib2: subordinate bus 4 pcib2: I/O decode 0x3000-0x3fff pcib2: memory decode 0xd4000000-0xd5ffffff pcib2: prefetched decode 0xd0000000-0xd1ffffff pci3: <ACPI PCI bus> on pcib2 pci3: physical bus=3 uhci0: <UHCI (generic) USB controller> port 0x1820-0x183f irq 23 at device 29.0 on pci0 uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1820 ioapic0: routing intpin 23 (PCI IRQ 23) to vector 49 uhci0: [GIANT-LOCKED] uhci0: [ITHREAD] usb0: <UHCI (generic) USB controller> on uhci0 usb0: USB revision 1.0 uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0 uhub0: 2 ports with 2 removable, self powered uhci1: <UHCI (generic) USB controller> port 0x1840-0x185f irq 19 at device 29.1 on pci0 uhci1: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1840 ioapic0: routing intpin 19 (PCI IRQ 19) to vector 50 uhci1: [GIANT-LOCKED] uhci1: [ITHREAD] usb1: <UHCI (generic) USB controller> on uhci1 usb1: USB revision 1.0 uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1 uhub1: 2 ports with 2 removable, self powered uhci2: <UHCI (generic) USB controller> port 0x1860-0x187f irq 18 at device 29.2 on pci0 uhci2: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1860 ioapic0: routing intpin 18 (PCI IRQ 18) to vector 51 uhci2: [GIANT-LOCKED] uhci2: [ITHREAD] usb2: <UHCI (generic) USB controller> on uhci2 usb2: USB revision 1.0 uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2 uhub2: 2 ports with 2 removable, self powered uhci3: <UHCI (generic) USB controller> port 0x1880-0x189f irq 16 at device 29.3 on pci0 uhci3: Reserved 0x20 bytes for rid 0x20 type 4 at 0x1880 ioapic0: routing intpin 16 (PCI IRQ 16) to vector 52 uhci3: [GIANT-LOCKED] uhci3: [ITHREAD] usb3: <UHCI (generic) USB controller> on uhci3 usb3: USB revision 1.0 uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3 uhub3: 2 ports with 2 removable, self powered ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xd8444000-0xd84443ff irq 23 at device 29.7 on pci0 ehci0: Reserved 0x400 bytes for rid 0x10 type 3 at 0xd8444000 ehci0: [GIANT-LOCKED] ehci0: [ITHREAD] usb4: EHCI version 1.0 usb4: companion controllers, 2 ports each: usb0 usb1 usb2 usb3 usb4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0 usb4: USB revision 2.0 uhub4: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4 uhub4: 8 ports with 8 removable, self powered ugen0: <Sonix Technology Co., Ltd. USB 2.0 Camera, class 239/2, rev 2.00/2.10, addr 2> on uhub4 pcib3: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pcib3: secondary bus 5 pcib3: subordinate bus 5 pcib3: I/O decode 0x0-0x0 pcib3: no prefetched decode pcib3: Subtractively decoded bridge. pci5: <ACPI PCI bus> on pcib3 pci5: physical bus=5 found-> vendor=0x1180, dev=0x0832, revid=0x00 bus=5, slot=5, func=0 class=0c-00-10, hdrtype=0x00, mfdev=1 cmdreg=0x0006, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x02 (500 ns), maxlat=0x04 (1000 ns) intpin=a, irq=11 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0xd8001000, size 11, enabled pcib3: requested memory range 0xd8001000-0xd80017ff: good pcib3: matched entry for 5.5.INTA pcib3: slot 5 INTA hardwired to IRQ 16 found-> vendor=0x1180, dev=0x0822, revid=0x19 bus=5, slot=5, func=1 class=08-05-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=3 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0xd8001800, size 8, memory disabled pcib3: requested memory range 0xd8001800-0xd80018ff: good pcib3: matched entry for 5.5.INTB pcib3: slot 5 INTB hardwired to IRQ 17 found-> vendor=0x1180, dev=0x0843, revid=0x01 bus=5, slot=5, func=2 class=08-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=3 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0xd8001c00, size 8, memory disabled pcib3: requested memory range 0xd8001c00-0xd8001cff: good pcib3: matched entry for 5.5.INTB pcib3: slot 5 INTB hardwired to IRQ 17 found-> vendor=0x1180, dev=0x0592, revid=0x0a bus=5, slot=5, func=3 class=08-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=3 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0xd8002000, size 8, memory disabled pcib3: requested memory range 0xd8002000-0xd80020ff: good pcib3: matched entry for 5.5.INTB pcib3: slot 5 INTB hardwired to IRQ 17 found-> vendor=0x1180, dev=0x0852, revid=0x05 bus=5, slot=5, func=4 class=08-80-00, hdrtype=0x00, mfdev=1 cmdreg=0x0000, statreg=0x0210, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns) intpin=b, irq=3 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0xd8002400, size 8, memory disabled pcib3: requested memory range 0xd8002400-0xd80024ff: good pcib3: matched entry for 5.5.INTB pcib3: slot 5 INTB hardwired to IRQ 17 found-> vendor=0x8086, dev=0x1092, revid=0x02 bus=5, slot=8, func=0 class=02-00-00, hdrtype=0x00, mfdev=0 cmdreg=0x0003, statreg=0x0290, cachelnsz=0 (dwords) lattimer=0x00 (0 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns) intpin=a, irq=10 powerspec 2 supports D0 D1 D2 D3 current D0 map[10]: type Memory, range 32, base 0xd8000000, size 12, enabled pcib3: requested memory range 0xd8000000-0xd8000fff: good map[14]: type I/O Port, range 32, base 0x4000, size 6, enabled pcib3: matched entry for 5.8.INTA pcib3: slot 8 INTA hardwired to IRQ 20 fwohci0: vendor=1180, dev=832 fwohci0: vendor=1180, dev=832 fwohci0: <1394 Open Host Controller Interface> mem 0xd8001000-0xd80017ff irq 16 at device 5.0 on pci5 fwohci0: Reserved 0x800 bytes for rid 0x10 type 3 at 0xd8001000 fwohci0: [MPSAFE] fwohci0: [FILTER] fwohci0: OHCI version 1.10 (ROM=0) fwohci0: No. of Isochronous channels is 4. fwohci0: EUI64 00:24:1b:00:bb:30:23:00 fwohci0: Phy 1394a available S400, 1 ports. fwohci0: Link S400, max_rec 2048 bytes. firewire0: <IEEE1394(FireWire) bus> on fwohci0 fwe0: <Ethernet over FireWire> on firewire0 if_fwe0: Fake Ethernet address: 02:24:1b:30:23:00 fwe0: bpf attached fwe0: Ethernet address: 02:24:1b:30:23:00 fwip0: <IP over FireWire> on firewire0 fwip0: bpf attached fwip0: Firewire address: 00:24:1b:00:bb:30:23:00 _at_ 0xfffe00000000, S400, maxrec 2048 sbp0: <SBP-2/SCSI over FireWire> on firewire0 dcons_crom0: <dcons configuration ROM> on firewire0 dcons_crom0: bus_addr 0x7d0c0000 fwohci0: Initiate bus reset fwohci0: BUS reset fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode pci5: <base peripheral> at device 5.1 (no driver attached) pci5: <base peripheral> at device 5.2 (no driver attached) pci5: <base peripheral> at device 5.3 (no driver attached) pci5: <base peripheral> at device 5.4 (no driver attached) fxp0: <Intel Pro/100 VE Network Connection> port 0x4000-0x403f mem 0xd8000000-0xd8000fff irq 20 at device 8.0 on pci5 fxp0: Reserved 0x1000 bytes for rid 0x10 type 3 at 0xd8000000 fxp0: using memory space register mapping fxp0: PCI IDs: 8086 1092 103c 30bb 0002 fxp0: Dynamic Standby mode is enabled miibus0: <MII bus> on fxp0 inphy0: <i82562ET 10/100 media interface> PHY 1 on miibus0 inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto fxp0: bpf attached fxp0: Ethernet address: 00:1b:24:49:da:97 ioapic0: routing intpin 20 (PCI IRQ 20) to vector 53 fxp0: [MPSAFE] fxp0: [ITHREAD] isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1810-0x181f at device 31.1 on pci0 atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0x1810 ata0: <ATA channel 0> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0 atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6 ata0: reset tp1 mask=03 ostat0=50 ostat1=00 ata0: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb ata0: stat1=0x00 err=0x00 lsb=0x00 msb=0x00 ata0: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER> ioapic0: routing intpin 14 (ISA IRQ 14) to vector 54 ata0: [MPSAFE] ata0: [ITHREAD] ata1: <ATA channel 1> on atapci0 atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170 atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376 ata1: reset tp1 mask=00 ostat0=ff ostat1=ff ioapic0: routing intpin 15 (ISA IRQ 15) to vector 55 ata1: [MPSAFE] ata1: [ITHREAD] atapci1: <Intel ICH7M SATA300 controller> port 0x18d0-0x18d7,0x18c4-0x18c7,0x18c8-0x18cf,0x18c0-0x18c3,0x18b0-0x18bf mem 0xd8444400-0xd84447ff irq 19 at device 31.2 on pci0 atapci1: Reserved 0x10 bytes for rid 0x20 type 4 at 0x18b0 atapci1: [MPSAFE] atapci1: [ITHREAD] atapci1: Reserved 0x400 bytes for rid 0x24 type 3 at 0xd8444400 atapci1: AHCI Version 01.10 controller with 4 ports detected ata2: <ATA channel 0> on atapci1 ata2: SATA connect time=0ms ata2: [MPSAFE] ata2: [ITHREAD] ata3: <ATA channel 1> on atapci1 ata3: port not implemented ata3: [MPSAFE] ata3: [ITHREAD] ata4: <ATA channel 2> on atapci1 ata4: SATA connect status=00000000 ata4: [MPSAFE] ata4: [ITHREAD] ata5: <ATA channel 3> on atapci1 ata5: port not implemented ata5: [MPSAFE] ata5: [ITHREAD] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) acpi_tz0: <Thermal Zone> on acpi0 atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 atkbd: the current kbd controller command byte 0047 atkbd: keyboard ID 0x41ab (2) kbd0 at atkbd0 kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000 ioapic0: routing intpin 1 (ISA IRQ 1) to vector 56 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] psm0: unable to allocate IRQ psmcpnp0: <PS/2 mouse port> irq 12 on acpi0 psm0: current command byte:0047 psm0: <PS/2 Mouse> irq 12 on atkbdc0 ioapic0: routing intpin 12 (ISA IRQ 12) to vector 57 psm0: [GIANT-LOCKED] psm0: [ITHREAD] psm0: model IntelliMouse, device ID 3-00, 3 buttons psm0: config:00000000, flags:00000008, packet size:4 psm0: syncmask:08, syncbits:00 unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff unknown: status reg test failed ff ex_isa_identify() ata: ata0 already exists; skipping it ata: ata1 already exists; skipping it atkbdc: atkbdc0 already exists; skipping it pnp_identify: Trying Read_Port at 203 pnp_identify: Trying Read_Port at 243 pnp_identify: Trying Read_Port at 283 pnp_identify: Trying Read_Port at 2c3 pnp_identify: Trying Read_Port at 303 pnp_identify: Trying Read_Port at 343 pnp_identify: Trying Read_Port at 383 pnp_identify: Trying Read_Port at 3c3 PNP Identify complete sc: sc0 already exists; skipping it vga: vga0 already exists; skipping it isa_probe_children: disabling PnP devices isa_probe_children: probing non-PnP devices pmtimer0 on isa0 orm0: <ISA Option ROMs> at iomem 0xce800-0xcffff,0xdf000-0xdf7ff,0xe0000-0xe17ff pnpid ORM0000 on isa0 adv0: not probed (disabled) aha0: not probed (disabled) aic0: not probed (disabled) bt0: not probed (disabled) cs0: not probed (disabled) ed0: not probed (disabled) fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0 fe0: not probed (disabled) ie0: not probed (disabled) le0: not probed (disabled) ppc0: parallel port not found. ppc0: <Parallel port> failed to probe at irq 7 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> sc0: fb0, kbd1, terminal emulator: sc (syscons terminal) sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0xeb9 0xeb9 0xeb9 0xeb9 sio0: probe failed test(s): 0 1 2 4 6 7 9 sio0: configured irq 4 not in bitmap of probed irqs 0 sio0: port may not be enabled sio0: irq maps: 0xeb9 0xeb9 0xeb9 0xeb9 sio0: probe failed test(s): 0 1 2 4 6 7 9 sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 sio0: type 8250 or not responding ioapic0: routing intpin 4 (ISA IRQ 4) to vector 58 sio0: [FILTER] sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled sio1: irq maps: 0xeb9 0xeb9 0xeb9 0xeb9 sio1: probe failed test(s): 0 1 2 4 6 7 9 sio1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0 sio2: not probed (disabled) sio3: not probed (disabled) sn0: not probed (disabled) vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 vt0: not probed (disabled) isa_probe_children: probing PnP devices Device configuration finished. Reducing kern.maxvnodes 133508 -> 100000 procfs registered lapic: Divisor 2, Frequency 66520468 hz Timecounter "TSC" frequency 1995613575 Hz quality -100 Timecounters tick every 1.000 msec lo0: bpf attached rr232x: no controller detected. firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me) firewire0: bus manager 0 (me) ata0-master: pio=PIO4 wdma=WDMA2 udma=UNSUPPORTED cable=40 wire acd0: setting PIO4 on ICH7 chip acpi_acad0: acline initialization start acpi_acad0: On Line acpi_acad0: acline initialization done, tried 1 times battery0: battery initialization start acd0: <MATSHITADVD-RAM UJ-851S/1.50> DVDR drive at ata0 as master acd0: read 4134KB/s (4134KB/s) write 4134KB/s (4134KB/s), 2048KB buffer, PIO4 acd0: Reads: CDR, CDRW, CDDA stream, DVDROM, DVDR, DVDRAM, packet acd0: Writes: CDR, CDRW, DVDR, DVDRAM, test write, burnproof acd0: Audio: play, 256 volume levels acd0: Mechanism: ejectable tray, unlocked acd0: Medium: no/blank disc ata2-master: pio=PIO4 wdma=WDMA2 udma=UDMA100 cable=40 wire ad4: 152627MB <TOSHIBA MK1637GSX DL032C> at ata2-master SATA150 ad4: 312581808 sectors [310101C/16H/63S] 16 sectors/interrupt 1 depth queue GEOM: new disk ad4 battery0: battery initialization done, tried 1 times ad4: Intel check1 failed ad4: Adaptec check1 failed ad4: LSI (v3) check1 failed ad4: LSI (v2) check1 failed ad4: FreeBSD check1 failed (probe0:sbp0:0:0:0): error 22 (probe0:sbp0:0:0:0): Unretryable Error (probe1:sbp0:0:1:0): error 22 (probe1:sbp0:0:1:0): Unretryable Error (probe2:sbp0:0:2:0): error 22 (probe2:sbp0:0:2:0): Unretryable Error (probe3:sbp0:0:3:0): error 22 (probe3:sbp0:0:3:0): Unretryable Error (probe4:sbp0:0:4:0): error 22 (probe4:sbp0:0:4:0): Unretryable Error (probe5:sbp0:0:5:0): error 22 (probe5:sbp0:0:5:0): Unretryable Error (probe6:sbp0:0:6:0): error 22 (probe6:sbp0:0:6:0): Unretryable Error ATA PseudoRAID loaded SMP: AP CPU #1 Launched! cpu1 AP: ID: 0x01000000 VER: 0x00050014 LDR: 0x00000000 DFR: 0xffffffff lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff timer: 0x000200ef therm: 0x00010200 err: 0x00010000 pcm: 0x00010000 ioapic0: Assigning ISA IRQ 1 to local APIC 0 ioapic0: Assigning ISA IRQ 4 to local APIC 1 ioapic0: Assigning ISA IRQ 9 to local APIC 0 ioapic0: Assigning ISA IRQ 12 to local APIC 1 ioapic0: Assigning ISA IRQ 14 to local APIC 0 ioapic0: Assigning ISA IRQ 15 to local APIC 1 ioapic0: Assigning PCI IRQ 16 to local APIC 0 ioapic0: Assigning PCI IRQ 18 to local APIC 1 ioapic0: Assigning PCI IRQ 19 to local APIC 0 ioapic0: Assigning PCI IRQ 20 to local APIC 1 ioapic0: Assigning PCI IRQ 23 to local APIC 0 WARNING: WITNESS option enabled, expect reduced performance. Trying to mount root from ufs:/dev/ad4s1a start_init: trying /sbin/init Linux ELF exec handler installedReceived on Sat Sep 08 2007 - 14:41:57 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:17 UTC