Re: lockup booting 8.0-CURRENT-200811 snap image

On Tuesday 18 November 2008 01:51:47 am Phil Oleson wrote:
> Hi, I've been trying to update my system to Current to try out the new 
> usb stack etc..
> and have had some problems.   Initially I attempted to just do a cvsup, 
> make buildworld,
> make kernel and had problems at the reboot.  Ended up having to use the 
> livecd to swap
> out the kernel (loader was strangely hanging before I could type unload; 
> boot kernel.old)
> 
> Anyways,  I picked up a new drive to split my system up to have a 
> working 7 & current.
> So, I downloaded the 200811 snap iso's for amd64 & i386 and tried to 
> boot to them.
> Same/similar lockup happens.. now since this board currently doesn't 
> have a serial port
> I've had to handtype what was left on the screen.. so hopefully it's 
> enough for now.
> 
> System: INTEL BLKDG35EC 775 G35  (flashed to the **ECG3510M.86A.0107** 
> Bios Image)
>               INTEL C2Q Q9300 2.5G 775
>               2 gigs memory (messed up on original order and havnt fixed 
> it yet)
>               using the built-in Intel video..
>            
> so the i386 and the amd64 dvd image I booted with had the same stopping 
> screen/output
> that I could see.. this is what I was able to get down from a verbose boot.
> 
> ------------------------------------------------------
>    Initial Probe      0   10    N     0  3 4 5 7 9 10 11 12
>    Validation         0   10    N     0  3 4 5 7 9 10 11 12
>    After Disable    0  255   N     0  3 4 5 7 9 10 11 12
> acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on 
> acpi0
> acpi_hpet0: vend: 0x8086 rev: 0x1 num: 2 hz: 14318180 opts: legacy_route 
> 64-bit Timecounter "HPET" frequency 143181800 Hz quality 900
> acpi_button0: <Sleep Button> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pci0: domain=0, physical bus=0
> found-> vendor=0x8086, dev=0x2980,  revid=0x03
>              domain=0, bus=0, slot=0, func=0
>              class=06-00-00, hdrtype=0x00, mfdev=0
>              cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords)
>              lattimer=0x00 (0 ns), mingnt=0x00 (0ns), maxlat=0x00 (0 ns)
> found-> vendor=0x8086, dev=0x2982,  revid=0x03
>              domain=0, bus=0, slot=2, func=0
>              class=03-00-00, hdrtype=0x00, mfdev=1
>              cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords)
>              lattimer=0x00 (0 ns), mingnt=0x00 (0ns), maxlat=0x00 (0 ns)
>              intpin=a,  irq=11
>              powerspec 2   supports D0 D3  current D0
>              MSI supports 1 message
>              map[10]: type Memory, range32, base 0x90200000, size 20, 
> enabled
> --------------------------------
> 
> 
> Any suggestions on how to proceed?
> 
> I'll see about installing the new install on the new drive starting at 
> RELENG_7
> and updating to HEAD from there.. so any source changes will have to wait on
> completing that.. but anything would help.

Try setting hw.pci.mcfg=0

-- 
John Baldwin