Pyun YongHyeon wrote: > Author: yongari > Date: Mon Dec 8 02:48:41 2008 > New Revision: 185756 > URL: http://svn.freebsd.org/changeset/base/185756 > > Log: > Reduce spin wait time consumed in GMII register access routines. > Waiting for 1ms for each GMII register access looks overkill and it > may also decrease overall performance of driver because re(4) > invokes mii_tick for every hz. > > Tested by: rpaulo > > Modified: > head/sys/dev/re/if_re.c > > Modified: head/sys/dev/re/if_re.c > ============================================================================== > --- head/sys/dev/re/if_re.c Mon Dec 8 02:38:13 2008 (r185755) > +++ head/sys/dev/re/if_re.c Mon Dec 8 02:48:41 2008 (r185756) > _at__at_ -417,13 +417,12 _at__at_ re_gmii_readreg(device_t dev, int phy, i > } > > CSR_WRITE_4(sc, RL_PHYAR, reg << 16); > - DELAY(1000); > > for (i = 0; i < RL_TIMEOUT; i++) { > + DELAY(30); > rval = CSR_READ_4(sc, RL_PHYAR); > if (rval & RL_PHYAR_BUSY) > break; > - DELAY(100); > } > > if (i == RL_TIMEOUT) { > _at__at_ -445,13 +444,12 _at__at_ re_gmii_writereg(device_t dev, int phy, > > CSR_WRITE_4(sc, RL_PHYAR, (reg << 16) | > (data & RL_PHYAR_PHYDATA) | RL_PHYAR_BUSY); > - DELAY(1000); > > for (i = 0; i < RL_TIMEOUT; i++) { > + DELAY(30); > rval = CSR_READ_4(sc, RL_PHYAR); > if (!(rval & RL_PHYAR_BUSY)) > break; > - DELAY(100); > } > > if (i == RL_TIMEOUT) { After this commit I see in logs errors: Dec 10 21:37:42 citrin kernel: re0: PHY read failed Dec 10 21:38:05 citrin last message repeated 3 times Dec 10 21:38:44 citrin last message repeated 3 times Dec 10 21:38:44 citrin kernel: re0: link state changed to DOWN Dec 10 21:38:45 citrin kernel: re0: link state changed to UP Dec 10 21:38:55 citrin kernel: re0: PHY read failed Dec 10 21:39:38 citrin last message repeated 3 times Dec 10 21:39:38 citrin kernel: re0: link state changed to DOWN Dec 10 21:39:39 citrin kernel: re0: link state changed to UP Dec 10 21:40:09 citrin kernel: re0: PHY read failed Dec 10 21:40:21 citrin kernel: re0: PHY read failed Dec 10 21:41:03 citrin kernel: re0: PHY read failed I tried to revert this patch - errors disappeared. HW: re0_at_pci0:2:5:0: class=0x020000 card=0xe0001458 chip=0x816710ec rev=0x10 hdr=0x00 vendor = 'Realtek Semiconductor' device = 'RTL8169/8110 Family Gigabit Ethernet NIC' class = network subclass = ethernet cap 01[dc] = powerspec 2 supports D0 D1 D2 D3 current D0 from dmesg: re0: <RealTek 8169SC/8110SC Single-chip Gigabit Ethernet> port 0xa000-0xa0ff mem 0xe1000000-0xe10000ff irq 21 at device 5.0 on pci2 re0: Chip rev. 0x18000000 re0: MAC rev. 0x00000000 -- Anton YuzhaninovReceived on Wed Dec 10 2008 - 17:58:42 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:38 UTC