On Feb 11, 2008 8:44 PM, David O'Brien <obrien_at_freebsd.org> wrote: > On Thu, Apr 19, 2007 at 02:13:46PM +0200, Gelsema, P (Patrick) wrote: > > I do have an Adaptec SCSI Controller, and yes I use it. I boot from it. > > > > ahd0: <Adaptec 39320D Ultra320 SCSI adapter> port > > 0xe800-0xe8ff,0xe400-0xe4ff mem 0xdd7fe000-0xdd7fffff irq 16 at devuce > > 10.0 on pci1 > > > > da0 at ahd0 bus 0 target 4 lun 0 > > da0: <SEAGATE ST336753LW HPS2> Fixed Direct Access SCSI-3 device > > da0: 160.000MB/s transfers (80.000MHz DT, offset 63, 16 bit) > > da0: Command Queueing Enabled > > da0: 34732MB (71132960 512 byte sectors: 255H 63S/T 4427C) > > > > Please note that the transferspeed is 160.00MB/s. In Freebsd 6.2 it's > > recognised as 320MB. > > Gelsema & Joćo, > > Do you still have your U320 disks running as U160 disks with an Adaptec > U320 controller in 7.0 or 8-CURRENT? I also have this problem and I've > traced it down to the CAM "NEW TRAN" code. > ---------------------------- > revision 1.166 > date: 2006/11/02 00:54:33; author: mjacob; state: Exp; lines: +0 -333 > 2nd and final commit that moves us to CAM_NEW_TRAN_CODE as the default. > ---------------------------- > > Given that we're not seeing tons of reports of this issue, I wonder if > its related to either revision of the ASIC or firmware. For comparison > here is my information from a verbose boot. > > ahd0: <Adaptec 39320 Ultra320 SCSI adapter> port 0xb000-0xb0ff,0xa800-0xa8ff mem 0xfa8f8000-0xfa8f9fff irq 29 at device 6.0 on pci4 > ahd0: Defaulting to MEMIO on > ahd0: Reserved 0x2000 bytes for rid 0x14 type 3 at 0xfa8f8000 > ahd0: Reading VPD from SEEPROM...ahd0: VPD parsing successful > ahd0: Reading SEEPROM...done. > ahd0: STPWLEVEL is on > ahd0: Manual Secondary Termination > ahd0: Primary High byte termination Enabled > ahd0: Primary Low byte termination Enabled > ahd0: Secondary High byte termination Disabled > ahd0: Secondary Low byte termination Disabled > ahd0: Downloading Sequencer Program... 752 instructions downloaded > ahd0: Features 0x101, Bugs 0x8ffe3f, Flags 0x43f1 > ahd0: [MPSAFE] > ahd0: [ITHREAD] > aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs > > -- > -- David (obrien_at_FreeBSD.org) > Q: Because it reverses the logical flow of conversation. > A: Why is top-posting (putting a reply at the top of the message) frowned upon? > Let's not play "Jeopardy-style quoting" I experience the same issue: ahd0: <Adaptec 29320 Ultra320 SCSI adapter> port 0xc000-0xc0ff,0xb800-0xb8ff mem 0xfeafc000-0xfeafdfff irq 23 at device 2.0 on pci5 ahd0: Defaulting to MEMIO on ahd0: Reserved 0x2000 bytes for rid 0x14 type 3 at 0xfeafc000 ahd0: Enabling 39Bit Addressing ahd0: Reading VPD from SEEPROM...ahd0: VPD parsing successful ahd0: Reading SEEPROM...done. ahd0: STPWLEVEL is on ahd0: Manual Secondary Termination ahd0: Primary High byte termination Enabled ahd0: Primary Low byte termination Enabled ahd0: Secondary High byte termination Disabled ahd0: Secondary Low byte termination Disabled ahd0: Downloading Sequencer Program... 753 instructions downloaded ahd0: Features 0x101, Bugs 0x8ffe3f, Flags 0x143f1 ahd0: [MPSAFE] ahd0: [ITHREAD] aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs da0 at ahd0 bus 0 target 0 lun 0 da0: <SEAGATE ST336807LW 0C01> Fixed Direct Access SCSI-3 device da0: Serial Number 3KT1F6PR00007546A9R2 da0: 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit) da0: Command Queueing Enabled da0: 35003MB (71687372 512 byte sectors: 255H 63S/T 4462C) --NikiReceived on Mon Feb 11 2008 - 20:31:01 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:27 UTC