Re: Call for testers: re(4) and RTL8168C/RTL8168CP/RTL8111C/RTL8111CP

On Sat, Jun 07, 2008 at 03:52:15PM +0900, Norikatsu Shigemura wrote:
 > On Sat, 7 Jun 2008 12:59:11 +0900
 > Pyun YongHyeon <pyunyh_at_gmail.com> wrote:
 > > I don't have any of these hardwares so if you have one of these
 > > hardwares please give it try and let me know how it goes. Some
 > > users reported success but I'd like to get more feedback because
 > > re(4) supports too many variants and I don't like to break supports
 > > for old RealTek hardwares.
 > 
 > 	Wow!! Quite Good Works my RTL8169SBL (cardbus).  I confirmed
 > 	following operations:
 > 
 > 	(ok) probe&attach
 > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 > re0: <RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet> port 0x3100-0x31ff mem 0xb0103000-0xb01031ff irq 22 at device 0.0 on cardbus0
 > re0: Chip rev. 0x10000000
 > re0: MAC rev. 0x00000000
 > miibus1: <MII bus> on re0
 > rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1
 > rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
 > re0: Ethernet address: 00:e0:4c:77:ab:e8
 > re0: [FILTER]
 > re0: link state changed to DOWN
 > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 > 
 > 	(ok) ifconfig re0 (w/o cable disconnect)
 > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 > re0: flags=8843<BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
 >         options=399b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_UCAST,WOL_MCAST,WOL_MAGIC>
 >         ether 00:e0:4c:77:ab:e8
 >         media: Ethernet autoselect (none)
 >         status: no carrier
 > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 > 
 > 	(ok) cable connected
 > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 > re0: link state changed to UP
 > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 > 
 > 	(ok) dhclient re0
 > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 > re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
 >         options=399b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4,WOL_UCAST,WOL_MCAST,WOL_MAGIC>
 >         ether 00:e0:4c:77:ab:e8
 >         inet 192.168.XXX.XXX netmask 0xffffff00 broadcast 192.168.XXX.255
 >         media: Ethernet autoselect (100baseTX <full-duplex>)
 >         status: active
 > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 > 
 > 	(ok) plug&pray
 > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 > rgephy0: detached
 > miibus1: detached
 > re0: detached
 > cardbus0: Expecting link target, got 0x0
 > re0: <RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet> port 0x3100-0x31ff mem 0xb0103000-0xb01031ff irq 22 at device 0.0 on cardbus0
 > re0: Chip rev. 0x10000000
 > re0: MAC rev. 0x00000000
 > miibus1: <MII bus> on re0
 > rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1
 > rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
 > re0: Ethernet address: 00:e0:4c:77:ab:e8
 > re0: [FILTER]
 > re0: link state changed to DOWN
 > re0: link state changed to UP
 > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
 > 
 > 	Of course, no panic!!  Thank you!!

Thanks for reporting.

-- 
Regards,
Pyun YongHyeon