Re: PERC6/i/e cli

Greetings,

Danny Braniss wrote:
> hi, mfi is ok,
>
> mfi0_at_pci0:1:0:0:        class=0x010400 card=0x1f0c1028 chip=0x00601000 
> rev=0x04 hdr=0x00
>     vendor     = 'LSI Logic (Was: Symbios Logic, NCR)'
>     device     = 'SAS1078 PCI-X Fusion-MPT SAS'
>     class      = mass storage
>     subclass   = RAID
>   

mfi0_at_pci0:1:0:0:        class=0x010400 card=0x1f0c1028 chip=0x00601000 
rev=0x04 hdr=0x00
    vendor     = 'LSI Logic (Was: Symbios Logic, NCR)'
    device     = 'SAS1078 PCI-X Fusion-MPT SAS'
    class      = mass storage
    subclass   = RAID
(exactly the same model)
and linux-megacli-1.01.40_1 works well with it. (freebsd 7 - amd64)

If you search the mailing lists you will find that similar problems can 
happen if
modules are not loaded in the proper way.

I have in /boot/loader.conf:
linux_load="YES"
mfi_linux_load="YES"

which loads:
linux.ko
mfi_linux.ko
and also: (because of fstab)
linprocfs.ko
linsysfs.ko

Then you can put in your periodic.conf - daily_status_mfi_raid_enable="YES"
and you will receive in your daily mails something like:

Virtual Drive Information:
VD  DRV RLP RLS RLQ STS    SIZE        STATE         NAME
0   2   1   0   0   64kB   139392MB    Optimal       

Ah and btw I think it was mandatory to have compat.linux.osrelease=2.6.12
(2.6.16 works too but you have to fix the script to not complain - i 
think the port is still not fixed?)

> mfi1_at_pci0:10:0:0:       class=0x010400 card=0x1f0a1028 chip=0x00601000 
> rev=0x04 hdr=0x00
>     vendor     = 'LSI Logic (Was: Symbios Logic, NCR)'
>     device     = 'SAS1078 PCI-X Fusion-MPT SAS'
>     class      = mass storage
>     subclass   = RAID
>
> ...
> mfi0: <Dell PERC 6> port 0xec00-0xecff mem 0xfc980000-0xfc9bffff,0xfc940000-0xf
> c97ffff irq 16 at device 0.0 on pci1
> mfi0: Megaraid SAS driver Ver 2.00 
> mfi0: [ITHREAD]
> pcib8: <ACPI PCI-PCI bridge> at device 4.0 on pci0
> pci10: <ACPI PCI bus> on pcib8
> mfi1: <Dell PERC 6> port 0xdc00-0xdcff mem 0xfc780000-0xfc7bffff,0xfc740000-0xf
> c77ffff irq 16 at device 0.0 on pci10
> mfi1: Megaraid SAS driver Ver 2.00 
> mfi1: [ITHREAD]
> ...
> mfid0: <MFI Logical Disk> on mfi0
> mfid0: 953344MB (1952448512 sectors) RAID volume '' is optimal
> mfid1: <MFI Logical Disk> on mfi1
> mfid1: 13346816MB (27334279168 sectors) RAID volume '' is optimal
>
> but megacli does not talk to it, am I missing something, or is there another
> cli that does work? 
>
> thanks,
> 	danny
>
>
> _______________________________________________
> freebsd-current_at_freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-current
> To unsubscribe, send any mail to "freebsd-current-unsubscribe_at_freebsd.org"
>   

-- 

Best Wishes,
Stefan Lambrev
ICQ# 24134177