A GENERIC kernel, full dmesg below. I was running fine from April 10th. Starting Network: lo0 em0. Additional routing options: IP gateway=YES. Fatal trap 12: page fault while in kernel mode cpuid = 0; apic id = 00 fault virtual address = 0x0 fault code = supervisor read, page not present instruction pointer = 0x20:0x0 stack pointer = 0x28:0xe6ae3ca8 frame pointer = 0x28:0xe6ae3cd4 code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = 0 (em0 taskq) [thread pid 0 tid 100037 ] Stopped at 0: *** error reading from address 0 *** db> bt Tracing pid 0 tid 100037 td 0xc683d000 taskqueue_run(c6894240,c689425c,c0c25dfe,0,c0c2db36,...) at taskqueue_run+0x10b taskqueue_thread_loop(c689b564,e6ae3d38,c0c2b242,32d,c0d795e0,...) at taskqueue_thread_loop+0x68 fork_exit(c088fdf0,c689b564,e6ae3d38) at fork_exit+0xb8 fork_trampoline() at fork_trampoline+0x8 --- trap 0, eip = 0, esp = 0xe6ae3d70, ebp = 0 --- db> GDB: no debug ports present KDB: debugger backends: ddb KDB: current backend: ddb Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 8.0-CURRENT #0: Thu Apr 23 10:31:18 EDT 2009 mdtancsa_at_i7.sentex.ca:/usr/obj/usr/src/sys/GENERIC WARNING: WITNESS option enabled, expect reduced performance. Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Core(TM) i7 CPU 920 _at_ 2.67GHz (2660.00-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x106a4 Stepping = 4 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x98e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT> AMD Features=0x28100000<NX,RDTSCP,LM> AMD Features2=0x1<LAHF> TSC: P-state invariant Cores per package: 8 Logical CPUs per core: 2 real memory = 3225419776 (3076 MB) avail memory = 3136049152 (2990 MB) ACPI APIC Table: <030609 APIC0930> FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs cpu0 (BSP): APIC ID: 0 cpu1 (AP/HT): APIC ID: 1 cpu2 (AP): APIC ID: 2 cpu3 (AP/HT): APIC ID: 3 cpu4 (AP): APIC ID: 4 cpu5 (AP/HT): APIC ID: 5 cpu6 (AP): APIC ID: 6 cpu7 (AP/HT): APIC ID: 7 WARNING: Non-uniform processors. WARNING: Using suboptimal topology. ioapic0 <Version 2.0> irqs 0-23 on motherboard kbd1 at kbdmux0 acpi0: <NEC > on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, bff00000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0 pci1: <ACPI PCI bus> on pcib1 em0: <Intel(R) PRO/1000 Network Connection 6.9.9> port 0xdc00-0xdc1f mem 0xfaee0000-0xfaefffff,0xfaedc000-0xfaedffff irq 16 at device 0.0 on pci1 em0: Using MSIX interrupts em0: [ITHREAD] em0: [ITHREAD] em0: [ITHREAD] em0: Ethernet address: 00:30:48:d7:c1:6e pcib2: <ACPI PCI-PCI bridge> at device 2.0 on pci0 pci2: <ACPI PCI bus> on pcib2 em1: <Intel(R) PRO/1000 Network Connection 6.9.9> port 0xec00-0xec1f mem 0xfafe0000-0xfaffffff,0xfafdc000-0xfafdffff irq 16 at device 0.0 on pci2 em1: Using MSIX interrupts em1: [ITHREAD] em1: [ITHREAD] em1: [ITHREAD] em1: Ethernet address: 00:30:48:d7:c1:6f pcib3: <ACPI PCI-PCI bridge> at device 3.0 on pci0 pci3: <ACPI PCI bus> on pcib3 pcib4: <ACPI PCI-PCI bridge> at device 7.0 on pci0 pci4: <ACPI PCI bus> on pcib4 pcib5: <ACPI PCI-PCI bridge> at device 9.0 on pci0 pci5: <ACPI PCI bus> on pcib5 pci0: <base peripheral, interrupt controller> at device 16.0 (no driver attached) pci0: <base peripheral, interrupt controller> at device 16.1 (no driver attached) pci0: <base peripheral, interrupt controller> at device 20.0 (no driver attached) pci0: <base peripheral, interrupt controller> at device 20.1 (no driver attached) pci0: <base peripheral, interrupt controller> at device 20.2 (no driver attached) pci0: <base peripheral, interrupt controller> at device 20.3 (no driver attached) pci0: <base peripheral> at device 22.0 (no driver attached) pci0: <base peripheral> at device 22.1 (no driver attached) pci0: <base peripheral> at device 22.2 (no driver attached) pci0: <base peripheral> at device 22.3 (no driver attached) pci0: <base peripheral> at device 22.4 (no driver attached) pci0: <base peripheral> at device 22.5 (no driver attached) pci0: <base peripheral> at device 22.6 (no driver attached) pci0: <base peripheral> at device 22.7 (no driver attached) uhci0: <UHCI (generic) USB controller> port 0xcc00-0xcc1f irq 16 at device 26.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x0f00 usbus0: <UHCI (generic) USB controller> on uhci0 uhci1: <UHCI (generic) USB controller> port 0xc880-0xc89f irq 21 at device 26.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x0f00 usbus1: <UHCI (generic) USB controller> on uhci1 uhci2: <UHCI (generic) USB controller> port 0xc800-0xc81f irq 19 at device 26.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x0f00 usbus2: <UHCI (generic) USB controller> on uhci2 ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfadde000-0xfadde3ff irq 18 at device 26.7 on pci0 ehci0: [ITHREAD] usbus3: EHCI version 1.0 usbus3: <EHCI (generic) USB 2.0 controller> on ehci0 uhci3: <UHCI (generic) USB controller> port 0xc480-0xc49f irq 23 at device 29.0 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x0f00 usbus4: <UHCI (generic) USB controller> on uhci3 uhci4: <UHCI (generic) USB controller> port 0xc400-0xc41f irq 19 at device 29.1 on pci0 uhci4: [ITHREAD] uhci4: LegSup = 0x0f00 usbus5: <UHCI (generic) USB controller> on uhci4 uhci5: <UHCI (generic) USB controller> port 0xc080-0xc09f irq 18 at device 29.2 on pci0 uhci5: [ITHREAD] uhci5: LegSup = 0x0f00 usbus6: <UHCI (generic) USB controller> on uhci5 ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfaddc000-0xfaddc3ff irq 23 at device 29.7 on pci0 ehci1: [ITHREAD] usbus7: EHCI version 1.0 usbus7: <EHCI (generic) USB 2.0 controller> on ehci1 pcib6: <ACPI PCI-PCI bridge> at device 30.0 on pci0 pci6: <ACPI PCI bus> on pcib6 vgapci0: <VGA-compatible display> mem 0xf9800000-0xf9ffffff,0xfbefc000-0xfbefffff,0xfb000000-0xfb7fffff irq 17 at device 4.0 on pci6 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 atapci0: <Intel ICH10 SATA300 controller> port 0xc000-0xc007,0xbc00-0xbc03,0xb880-0xb887,0xb800-0xb803,0xb480-0xb48f,0xb400-0xb40f irq 19 at device 31.2 on pci0 atapci0: [ITHREAD] ata2: <ATA channel 0> on atapci0 ata2: [ITHREAD] ata3: <ATA channel 1> on atapci0 ata3: [ITHREAD] pci0: <serial bus, SMBus> at device 31.3 (no driver attached) atapci1: <Intel ICH10 SATA300 controller> port 0xb000-0xb007,0xac00-0xac03,0xa880-0xa887,0xa800-0xa803,0xa480-0xa48f,0xa400-0xa40f irq 19 at device 31.5 on pci0 atapci1: [ITHREAD] ata4: <ATA channel 0> on atapci1 ata4: [ITHREAD] ata5: <ATA channel 1> on atapci1 ata5: [ITHREAD] acpi_button0: <Power Button> on acpi0 atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] uart0: console (115200,n,8,1) uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0 uart1: [FILTER] uart2: <16550 or compatible> port 0x3e8-0x3ef irq 5 on acpi0 uart2: [FILTER] atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 atkbd0: <AT Keyboard> irq 1 on atkbdc0 kbd0 at atkbd0 atkbd0: [GIANT-LOCKED] atkbd0: [ITHREAD] cpu0: <ACPI CPU> on acpi0 ACPI Warning (tbutils-0243): Incorrect checksum in table [OEMB] - 8F, should be 8C [20070320] est0: <Enhanced SpeedStep Frequency Control> on cpu0 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 14 device_attach: est0 attach returned 6 p4tcc0: <CPU Frequency Thermal Control> on cpu0 cpu1: <ACPI CPU> on acpi0 est1: <Enhanced SpeedStep Frequency Control> on cpu1 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 14 device_attach: est1 attach returned 6 p4tcc1: <CPU Frequency Thermal Control> on cpu1 cpu2: <ACPI CPU> on acpi0 est2: <Enhanced SpeedStep Frequency Control> on cpu2 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 14 device_attach: est2 attach returned 6 p4tcc2: <CPU Frequency Thermal Control> on cpu2 cpu3: <ACPI CPU> on acpi0 est3: <Enhanced SpeedStep Frequency Control> on cpu3 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 14 device_attach: est3 attach returned 6 p4tcc3: <CPU Frequency Thermal Control> on cpu3 cpu4: <ACPI CPU> on acpi0 est4: <Enhanced SpeedStep Frequency Control> on cpu4 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 14 device_attach: est4 attach returned 6 p4tcc4: <CPU Frequency Thermal Control> on cpu4 cpu5: <ACPI CPU> on acpi0 est5: <Enhanced SpeedStep Frequency Control> on cpu5 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 14 device_attach: est5 attach returned 6 p4tcc5: <CPU Frequency Thermal Control> on cpu5 cpu6: <ACPI CPU> on acpi0 est6: <Enhanced SpeedStep Frequency Control> on cpu6 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 14 device_attach: est6 attach returned 6 p4tcc6: <CPU Frequency Thermal Control> on cpu6 cpu7: <ACPI CPU> on acpi0 est7: <Enhanced SpeedStep Frequency Control> on cpu7 est: CPU supports Enhanced Speedstep, but is not recognized. est: cpu_vendor GenuineIntel, msr 14 device_attach: est7 attach returned 6 p4tcc7: <CPU Frequency Thermal Control> on cpu7 pmtimer0 on isa0 orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff pnpid ORM0000 on isa0 sc0: <System console> at flags 0x100 on isa0 sc0: VGA <16 virtual consoles, flags=0x300> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0 ata0: [ITHREAD] ata1 at port 0x170-0x177,0x376 irq 15 on isa0 ata1: [ITHREAD] ppc0: parallel port not found. Timecounters tick every 1.000 msec usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 ugen0.1: <Intel> at usbus0 uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0 ugen1.1: <Intel> at usbus1 uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1 ugen2.1: <Intel> at usbus2 uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2 ugen3.1: <Intel> at usbus3 uhub3: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 usbus6: 12Mbps Full Speed USB v1.0 usbus7: 480Mbps High Speed USB v2.0 ugen4.1: <Intel> at usbus4 uhub4: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 ugen5.1: <Intel> at usbus5 uhub5: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus5 ugen6.1: <Intel> at usbus6 uhub6: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6 ugen7.1: <Intel> at usbus7 uhub7: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus7 ad4: 76319MB <Seagate ST380811AS 3.AAE> at ata2-master SATA300 acd0: DVDROM <DVD-ROM UJDA780/1.50> at ata2-slave UDMA33 SMP: AP CPU #3 Launched! SMP: AP CPU #1 Launched! SMP: AP CPU #2 Launched! SMP: AP CPU #6 Launched! SMP: AP CPU #7 Launched! SMP: AP CPU #4 Launched! SMP: AP CPU #5 Launched! WARNING: WITNESS option enabled, expect reduced performance. GEOM_LABEL: Label for provider ad4s1a is ufsid/49d5f97eae95c933. GEOM_LABEL: Label for provider ad4s1d is ufsid/49d5f97edfe5e187. :EOM_LABEL: Label for provider ad4s1e is ufsid/49d5f97e2c96fuch0ubb.0 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered GEOM_LABEL: Label for provider ad4s1f is ufsid/49d5f9822bc88fc6. Root mount waiting for: usbus7 usbus6 usbus5 usbus4 usbus3 uhub5: 2 ports with 2 removable, self powered uhub6: 2 ports with 2 removable, self powered uhub4: 2 ports with 2 removable, self powered Root mount waiting for: usbus7 usbus3 Root mount waiting for: usbus7 usbus3 uhub3: 6 ports with 6 removable, self powered uhub7: 6 ports with 6 removable, self powered Trying to mount root from ufs:/dev/ad4s1a WARNING: / was not properly dismounted Entropy harvesting: interrupts ethernet point_to_point kickstart. GEOM_LABEL: Label ufsid/49d5f97eae95c933 removed. /dev/ad4s1a: 4182 files, 206573 used, 299914 free (850 frags, 37383 blocks, 0.2% fragmentation) GEOM_LABEL: Label for provider ad4s1a is ufsid/49d5f97eae95c933. GEOM_LABEL: Label ufsid/49d5f97edfe5e187 removed. /dev/ad4s1d: 100 files, 730 used, 2028301 free (149 frags, 253519 blocks, 0.0% fragmentation) GEOM_LABEL: Label for provider ad4s1d is ufsid/49d5f97edfe5e187. GEOM_LABEL: Label ufsid/49d5f97e2c96fc0b removed. /dev/ad4s1e: 317627 files, 2023068 used, 18288330 free (102938 frags, 2273174 blocks, 0.5% fragmentation) GEOM_LABEL: Label for provider ad4s1e is ufsid/49d5f97e2c96fc0b. GEOM_LABEL: Label ufsid/49d5f9822bc88fc6 removed. /dev/ad4s1f: FREE BLK COUNT(S) WRONG IN SUPERBLK (SALVAGED) /dev/ad4s1f: SUMMARY INFORMATION BAD (SALVAGED) /dev/ad4s1f: BLK(S) MISSING IN BIT MAPS (SALVAGED) /dev/ad4s1f: 1374 files, 31882 used, 10900969 free (425 frags, 1362568 blocks, 0.0% fragmentation) GEOM_LABEL: Label for provider ad4s1f is ufsid/49d5f9822bc88fc6. GEOM_LABEL: Label ufsid/49d5f97eae95c933 removed. GEOM_LABEL: Label ufsid/49d5f97edfe5e187 removed. GEOM_LABEL: Label ufsid/49d5f97e2c96fc0b removed. GEOM_LABEL: Label ufsid/49d5f9822bc88fc6 removed. Starting Network: lo0 em0. Additional routing options: IP gateway=YES. Fatal trap 12: page fault while in kernel mode cpuid = 1; apic id = 01 fault virtual address = 0x0 fault code = supervisor read, page not present instruction pointer = 0x20:0x0 stack pointer = 0x28:0xe6ae3ca8 frame pointer = 0x28:0xe6ae3cd4 code segmsavecore: rebooten after panic: frtom debugger Apr 23 11:15:14 i7 =savecore: reboot b after panic: frasom debugger e 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = 0 (em0 taskq) [thread pid 0 tid 100037 ] Stopped at 0: *** error reading from address 0 *** db> -------------------------------------------------------------------- Mike Tancsa, tel +1 519 651 3400 Sentex Communications, mike_at_sentex.net Providing Internet since 1994 www.sentex.net Cambridge, Ontario Canada www.sentex.net/mikeReceived on Thu Apr 23 2009 - 13:20:44 UTC
This archive was generated by hypermail 2.4.0 : Wed May 19 2021 - 11:39:46 UTC